I have a ~1 year old Western Digital Caviar Blue WD10EZEX that is not in
the drive database (just updated).
Here is the output of smartctl -x -q noserial ...
Let me know If I can be of any use.
Thanks.
François
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.8.0-26-generic] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD10EZEX-00RKKA0
Firmware Version: 80.00A80
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Jul 16 09:29:28 2013 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10260) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 118) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x30b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 175 175 021 - 2225
4 Start_Stop_Count -O--CK 100 100 000 - 118
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 090 090 000 - 7833
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 114
192 Power-Off_Retract_Count -O--CK 200 200 000 - 43
193 Load_Cycle_Count -O--CK 200 200 000 - 74
194 Temperature_Celsius -O---K 102 101 000 - 41
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error log]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaa has 1 sectors [Device vendor specific log]
GP/S Log at address 0xab has 1 sectors [Device vendor specific log]
GP/S Log at address 0xac has 1 sectors [Device vendor specific log]
GP/S Log at address 0xad has 1 sectors [Device vendor specific log]
GP/S Log at address 0xae has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaf has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log]
GP Log at address 0xb6 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xbd has 1 sectors [Device vendor specific log]
GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log]
GP Log at address 0xc1 has 93 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 21
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 21 [20] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:32.210 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:32.024 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:31.567 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:30.577 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:21.423 SMART WRITE LOG
Error 20 [19] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:32.024 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:31.567 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:30.577 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:21.423 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:08.634 SMART WRITE LOG
Error 19 [18] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:31.567 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:30.577 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:21.423 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:08.634 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:07.472 SMART WRITE LOG
Error 18 [17] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:06:30.577 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:21.423 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:08.634 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:07.472 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:01.799 SMART WRITE LOG
Error 17 [16] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:21.423 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:08.634 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:07.472 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:01.799 SMART WRITE LOG
b0 00 da 00 00 00 00 00 c2 4f 00 00 08 00:00:45.121 SMART RETURN STATUS
Error 16 [15] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:08.634 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:07.472 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:01.799 SMART WRITE LOG
b0 00 da 00 00 00 00 00 c2 4f 00 00 08 00:00:45.121 SMART RETURN STATUS
b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 00:00:45.119 SMART READ DATA
Error 15 [14] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:07.472 SMART WRITE LOG
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:01.799 SMART WRITE LOG
b0 00 da 00 00 00 00 00 c2 4f 00 00 08 00:00:45.121 SMART RETURN STATUS
b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 00:00:45.119 SMART READ DATA
b0 00 d1 00 01 00 00 00 c2 4f 00 00 08 00:00:45.114 SMART READ ATTRIBUTE
THRESHOLDS [OBS-4]
Error 14 [13] occurred at disk power-on lifetime: 6031 hours (251 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
b0 00 d6 00 01 00 00 00 c2 4f e0 00 08 00:05:01.799 SMART WRITE LOG
b0 00 da 00 00 00 00 00 c2 4f 00 00 08 00:00:45.121 SMART RETURN STATUS
b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 00:00:45.119 SMART READ DATA
b0 00 d1 00 01 00 00 00 c2 4f 00 00 08 00:00:45.114 SMART READ ATTRIBUTE
THRESHOLDS [OBS-4]
e5 00 00 00 00 00 00 00 00 00 00 00 08 00:00:45.114 CHECK POWER MODE
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 5642 -
# 2 Extended offline Completed without error 00% 2697 -
# 3 Short offline Completed without error 00% 2695 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 41 Celsius
Power Cycle Min/Max Temperature: 22/42 Celsius
Lifetime Min/Max Temperature: 22/42 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (333)
Index Estimated Time Temperature Celsius
334 2013-07-16 01:32 41 **********************
... ..(476 skipped). .. **********************
333 2013-07-16 09:29 41 **********************
Warning: device does not support SCT Error Recovery Control command
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 8 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 8 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 3630156 Vendor specific
------------------------------------------------------------------------------
See everything from the browser to the database with AppDynamics
Get end-to-end visibility with application monitoring from AppDynamics
Isolate bottlenecks and diagnose root cause in seconds.
Start your free trial of AppDynamics Pro today!
http://pubads.g.doubleclick.net/gampad/clk?id=48808831&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
