--
NEU: FreePhone - 0ct/min Handyspartarif mit Geld-zurück-Garantie!
Jetzt informieren: http://www.gmx.net/de/go/freephone
smartctl 5.42 2011-10-11 r3440 [x86_64-linux-2.6.39.4-1000hz] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST3250823ACE
Serial Number: 5ND13Q5X
Firmware Version: 3.03
User Capacity: 250.059.350.016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Oct 14 18:13:38 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15556) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 055 048 006 Pre-fail Always
- 18317422
3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always
- 2348
5 Reallocated_Sector_Ct 0x0033 096 096 036 Pre-fail Always
- 184
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always
- 20531143
9 Power_On_Hours 0x0032 096 096 000 Old_age Always
- 4250
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always
- 2212
194 Temperature_Celsius 0x0022 036 050 000 Old_age Always
- 36 (0 13 0 0 0)
195 Hardware_ECC_Recovered 0x001a 055 048 000 Old_age Always
- 18317422
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline
- 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 21 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 21 occurred at disk power-on lifetime: 3804 hours (158 days + 12 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 55 e2 0a 40 Error: UNC at LBA = 0x000ae255 = 713301
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 04 54 e2 0a 40 00 00:00:55.845 READ DMA
ca 00 04 60 e2 0a 40 00 00:00:53.821 WRITE DMA
ca 00 04 60 e2 0a 40 00 00:00:52.869 WRITE DMA
ca 00 40 0c 12 0b 40 00 00:00:52.838 WRITE DMA
c8 00 40 0c 12 0b 40 00 00:00:52.768 READ DMA
Error 20 occurred at disk power-on lifetime: 3736 hours (155 days + 16 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 5c e2 0a 40 Error: UNC 4 sectors at LBA = 0x000ae25c = 713308
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 04 5c e2 0a 40 00 00:00:11.568 READ DMA
c8 00 04 cc 06 0b 40 00 00:00:11.887 READ DMA
c8 00 04 58 e2 0a 40 00 00:00:11.730 READ DMA
c8 00 04 20 0b 00 40 00 00:00:11.657 READ DMA
c8 00 04 20 00 00 40 00 00:00:11.654 READ DMA
Error 19 occurred at disk power-on lifetime: 3720 hours (155 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 66 08 0b 40 Error: UNC at LBA = 0x000b0866 = 723046
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 4c 08 0b 40 00 00:00:13.609 READ DMA
c8 00 04 6c e2 0a 40 00 00:00:12.607 READ DMA
ca 00 04 60 e2 0a 40 00 00:00:12.545 WRITE DMA
c8 00 40 0c 12 0b 40 00 00:00:12.368 READ DMA
c8 00 04 60 e2 0a 40 00 00:00:12.361 READ DMA
Error 18 occurred at disk power-on lifetime: 3717 hours (154 days + 21 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 cd 06 0b 40 Error: UNC at LBA = 0x000b06cd = 722637
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 04 cc 06 0b 40 00 00:00:12.370 READ DMA
c8 00 04 58 e2 0a 40 00 00:00:12.363 READ DMA
c8 00 04 20 0b 00 40 00 00:00:12.361 READ DMA
c8 00 04 20 00 00 40 00 00:00:12.352 READ DMA
ca 00 04 0c 00 00 40 00 00:00:12.531 WRITE DMA
Error 17 occurred at disk power-on lifetime: 3672 hours (153 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 50 13 0b 40 Error: UNC at LBA = 0x000b1350 = 725840
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 e0 40 13 0b 40 00 00:00:55.873 READ DMA
c8 00 f4 4c 12 0b 40 00 00:00:55.870 READ DMA
c8 00 04 58 16 01 40 00 00:00:55.867 READ DMA
c8 00 04 08 11 09 40 00 00:00:55.830 READ DMA
c8 00 04 04 11 09 40 00 00:00:55.827 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 4249 -
# 2 Short offline Completed without error 00% 4247 -
# 3 Short offline Aborted by host 10% 4208 -
# 4 Extended offline Completed without error 00% 4129 -
# 5 Short offline Completed without error 00% 4128 -
# 6 Short offline Interrupted (host reset) 10% 4127 -
# 7 Short offline Interrupted (host reset) 10% 4119 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
------------------------------------------------------------------------------
All the data continuously generated in your IT infrastructure contains a
definitive record of customers, application performance, security
threats, fraudulent activity and more. Splunk takes this data and makes
sense of it. Business sense. IT sense. Common sense.
http://p.sf.net/sfu/splunk-d2d-oct
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
