output of smartctl -a (after running smartctl --test=long) is attached.
(40GB 2.5" PATA disk)
smartctl 5.40 2010-04-20 r3084 [i686-suse-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG MP0402H
Serial Number: S03WJ10X622985
Firmware Version: UC100-11
User Capacity: 40.060.403.712 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Sun Apr 25 22:10:20 2010 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (2400) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 40) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0007 090 088 011 Pre-fail Always
- 2496
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 838
5 Reallocated_Sector_Ct 0x0033 100 100 011 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always
- 0
8 Seek_Time_Performance 0x0025 100 100 011 Pre-fail Offline
- 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 53726
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 548
191 G-Sense_Error_Rate 0x0012 100 100 000 Old_age Always
- 4882
194 Temperature_Celsius 0x0022 121 097 000 Old_age Always
- 39
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always
- 26975082
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x000a 100 100 051 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x0012 100 100 000 Old_age Always
- 0
223 Load_Retry_Count 0x0012 100 100 000 Old_age Always
- 0
225 Load_Cycle_Count 0x0012 092 092 000 Old_age Always
- 90776
255 Unknown_Attribute 0x000a 100 100 051 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 214 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 214 occurred at disk power-on lifetime: 443 hours (18 days + 11 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 fe 00 00 00 40 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 05 fe 00 00 00 40 00 00:37:45.250 SET FEATURES [Enable APM]
c8 00 20 5f 5f 5b e0 00 00:37:45.250 READ DMA
c8 00 88 7f 5f 5b e0 00 00:37:45.250 READ DMA
c8 00 20 3f 5f 5b e0 00 00:37:45.250 READ DMA
c8 00 68 5f 7e 68 e0 00 00:37:45.188 READ DMA
Error 213 occurred at disk power-on lifetime: 443 hours (18 days + 11 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 fe 00 00 00 40 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 05 fe 00 00 00 40 00 00:23:32.750 SET FEATURES [Enable APM]
c8 00 20 5f 5f 5b e0 00 00:23:32.750 READ DMA
c8 00 88 7f 5f 5b e0 00 00:23:32.750 READ DMA
c8 00 20 3f 5f 5b e0 00 00:23:32.688 READ DMA
c8 00 80 5f 61 56 e0 00 00:23:32.688 READ DMA
Error 212 occurred at disk power-on lifetime: 442 hours (18 days + 10 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 fe 00 00 00 40 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 05 fe 00 00 00 40 00 00:01:07.813 SET FEATURES [Enable APM]
c8 00 18 07 d9 52 e0 00 00:01:07.813 READ DMA
c8 00 20 57 bd 51 e0 00 00:01:07.813 READ DMA
c8 00 08 97 71 04 e0 00 00:01:07.813 READ DMA
c8 00 00 e7 d2 6e e0 00 00:01:07.813 READ DMA
Error 211 occurred at disk power-on lifetime: 442 hours (18 days + 10 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 fe 00 00 00 40 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 05 fe 00 00 00 40 00 00:28:02.563 SET FEATURES [Enable APM]
c8 00 20 5f 5f 5b e0 00 00:28:02.563 READ DMA
c8 00 88 7f 5f 5b e0 00 00:28:02.500 READ DMA
c8 00 20 3f 5f 5b e0 00 00:28:02.500 READ DMA
c8 00 80 5f 61 56 e0 00 00:28:02.500 READ DMA
Error 210 occurred at disk power-on lifetime: 442 hours (18 days + 10 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 fe 00 00 00 40 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 05 fe 00 00 00 40 00 00:21:31.188 SET FEATURES [Enable APM]
c8 00 08 ff 69 41 e0 00 00:21:31.125 READ DMA
c8 00 08 af 61 c9 e0 00 00:21:30.875 READ DMA
c8 00 08 77 c5 bf e0 00 00:21:30.875 READ DMA
c8 00 08 df 69 41 e0 00 00:21:30.875 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Extended offline Completed without error 00% 447 -
# 2 Short offline Completed without error 00% 1 -
Device does not support Selective Self Tests/Logging
------------------------------------------------------------------------------
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
