It dosn't report th amount of video RAM. It doesn't
say anything except "clocked fail". I do not know the
amout of video RAM I have.
--- [EMAIL PROTECTED] wrote:
>
> Did it at least report the amount of video RAM?
> If so use generic video card, no clockchip, the
> right amount of RAM.
>
> Miguel Dilaj
>
>
>
>
>
> Yu Ye Zhou <[EMAIL PROTECTED]>@redhat.com on
> 25/07/2001 13:49:45
>
> Please respond to [EMAIL PROTECTED]
>
> Sent by: [EMAIL PROTECTED]
>
>
> To: [EMAIL PROTECTED]
> cc:
> Subject: RE: failed to connect to section manager
>
>
> I also use superProbe. After I used it, it says
> clock
> failed and use default setting.
>
> Thanks.
> Yu Ye Zhou
>
> --- [EMAIL PROTECTED] wrote:
> >
> > Some time ago, when my videocard was not
> > autodetected, I used SuperProbe to
> > check its settings. I don't know if it's still
> > shipping with XFree.
> > Be careful with SuperProbe (hint: turn off your
> > Monitor before SuperProbe
> > starts, leave it off 30 seconds, then turn it on
> > again).
> > Best regards
> >
> > Miguel Dilaj
> >
> >
> >
> >
> >
> > Yu Ye Zhou <[EMAIL PROTECTED]>@redhat.com on
> > 25/07/2001 11:56:48
> >
> > Please respond to [EMAIL PROTECTED]
> >
> > Sent by: [EMAIL PROTECTED]
> >
> >
> > To: [EMAIL PROTECTED]
> > cc:
> > Subject: RE: failed to connect to section manager
> >
> >
> > I'm using the generic video card. I'm not sure how
> > many memory I have for the card. I only randomly
> > picked some values. Would I destroy my hardware if
> > the
> > amout of memory I choose is too high?
> >
> > --- "Taylor, ForrestX" <[EMAIL PROTECTED]>
> > wrote:
> > > What kind of video card do you have?
> > >
> > > Forrest
> > >
> > > > -----Original Message-----
> > > > From: Yu Ye Zhou [mailto:[EMAIL PROTECTED]]
> > > > Sent: Monday, July 23, 2001 3:33 PM
> > > > To: [EMAIL PROTECTED]
> > > > Subject: RE: failed to connect to section
> > manager
> > > >
> > > >
> > > > Yes, I tried it too. It is still the same.
> when
> > I
> > > use
> > > > promb. It says clocked promb failed, use
> default
> > > > value. At the end, still some configuration
> > error
> > > that
> > > > I either have to exit or go back.
> > > >
> > > >
> > > > --- "Taylor, ForrestX"
> > <[EMAIL PROTECTED]>
> > > > wrote:
> > > > > Try just using Xconfigurator. It will use
> X3
> > > > > instead of X4.
> > > > >
> > > > > Forrest
> > > > >
> > > > > > -----Original Message-----
> > > > > > From: Yu Ye Zhou
> [mailto:[EMAIL PROTECTED]]
> > > > > > Sent: Monday, July 23, 2001 3:03 PM
> > > > > > To: [EMAIL PROTECTED]
> > > > > > Subject: RE: faile to connect to section
> > > manager
> > > > > >
> > > > > >
> > > > > > I successfully install the two files and
> run
> > > the
> > > > > the
> > > > > > mouseconfig to reconfi the mouse. However,
> > > I've
> > > > > tried
> > > > > > many times Xconfigurator --preferxf4. I'm
> > very
> > > > > sure
> > > > > > that my vedio card is generic vedio card
> and
> > > my
> > > > > > monitor is Princeton E070. However, every
> > time
> > > I
> > > > > > configure, to the end after it says the
> > "start
> > > the
> > > > > X
> > > > > > server", it always says that
> configratition
> > > > > > configuration error and ask me either go
> > back
> > > or
> > > > > exit.
> > > > > > I'm not sure of how many ram my vedio card
> > > has. I
> > > > > only
> > > > > > randomly pick 32mb, 16mb, 2mb etc.
> > > > > >
> > > > > >
> > > > > > --- "Taylor, ForrestX"
> > > <[EMAIL PROTECTED]>
> > > > > > wrote:
> > > > > > >
> > > > > >
> > > > >
> > > >
> > >
> >
>
http://www.redhat.com/support/errata/RHBA-2001-062.html
> > > > > > >
> > > > > > > Get the two under i386.
> > > > > > >
> > > > > > > Then install them with
> > > > > > >
> > > > > > > rpm -Uvh Xconfigurator-4.9.29-1.i386.rpm
> > > > > > > mouseconfig-4.22-1.i386.rpm
> > > > > > >
> > > > > > > Forrest
> > > > > > >
> > > > > > > > -----Original Message-----
> > > > > > > > From: Yu Ye Zhou
> > > [mailto:[EMAIL PROTECTED]]
> > > > > > > > Sent: Monday, July 23, 2001 1:23 PM
> > > > > > > > To: [EMAIL PROTECTED]
> > > > > > > > Subject: RE: faile to connect to
> section
> > > > > manager
> > > > > > > >
> > > > > > > >
> > > > > > > > Where can I dowload those the
> > mouseconfig
> > > and
> > > > > the
> > > > > > > > Xconfigurator?
> > > > > > > >
> > > > > > > > --- Chris Kloiber
> <[EMAIL PROTECTED]>
> > > wrote:
> > > > > > > > > On Mon, 23 Jul 2001, Yu Ye Zhou
> wrote:
> > > > > > > > >
> > > > > > > > > > I'm using the one come with 7.1.
> > Even
> > > I
> > > > > try
> > > > > > > > > > mouseconfig, there is still the
> same
> > > error
> > > > > > > reading
> > > > > > > > > the
> > > > > > > > > > sysconfig/mouse file.
> > > > > > > > >
> > > > > > > > > The stock mouseconfig is busted, get
> > the
> > > new
> > > > > > > version
>
=== message truncated ===
__________________________________________________
Do You Yahoo!?
Make international calls for as low as $.04/minute with Yahoo! Messenger
http://phonecard.yahoo.com/
_______________________________________________
Seawolf-list mailing list
[EMAIL PROTECTED]
https://listman.redhat.com/mailman/listinfo/seawolf-list
