I'm interested in using a E320 via POE+ to deliver 12v power. Does anyone have
suggestions for injectors/adapters to use in combination with the E320? POE+ is
supposed to be able to deliver up to 30W, which is conveniently how the E320 is
12V rated. I found one an Amazon that will do 24W (SMAKN®
Hi Austin,
>Is there a way to do it directly via the jtag and using the screen command
to speak with the N310?
You could connect to the ARM via JTAG as detailed in the link below, but
you're better off just SSH'ing into it.
https://kb.ettus.com/USRP_N300/N310/N320/N321_Getting_Started_Guide#Conn
Let’s do some quick math, shall we?
5msps with 16-bit complex == 160Mbit/second
1.25msps with 16-bit complex samples == an additional 40mbit-second
Unless you have super reliable 1Gig wireless infrastructure, this just isn’t
going to work.
Sent from my iPhone
> On Jan 28, 2020, at 6:23 PM, A
Hey Nate,
Thanks for the quick response as always! I tried editing those files in the
past, but I remember having issues because they were locked or I wasn’t able to
actually save any changes that I made. Is there a way to do it directly via the
jtag and using the screen command to speak with th
Hi Austin,
The MTUs on your host and N310 must match. You should modify the systemd
configuration on the N310 are restart the whole device or restart
systemd-networkd
https://kb.ettus.com/USRP_N300/N310/N320/N321_Getting_Started_Guide#Updating_the_Network_Configurations
It is not recommended to
Hi everyone,
I have a very basic GNU script with just a USRP block and a time sink that
when I run, there are tons of streaming errors with the tx and rx. In GNU,
the console is being filled with 'D's and the console for the N210 is
getting filled with 'U's and 'S's.
My setup is just a USRP N210 c
Hello,
I have an application that schedules transmissions/receives on a short time
scale (order of tens of microseconds). I'm attempting to gauge the feasibility
of using a x310 with UBX-160 daughterboards and 10Gb ethernet for the
application.
I wrote a quick test to see approximately how l
Hi Sammy,
>Can I turn it off and come back the next day and still have the same phase
offset between the channels that I had the day before?
Yes. This assumes that you are running with the same frequency, gain,
sample rate and system temperature that your calibrations were made with.
Also unless
Hi Jean Marie - Have you tried the instructions here <
https://kb.ettus.com/Writing_the_USRP_File_System_Disk_Image_to_a_SD_Card
>? Guessing those will do the trick for you. Hope this is useful! - MLD
On Mon, Jan 27, 2020 at 9:13 AM Jean Marie Brieussel via USRP-users <
usrp-users@lists.ettus.com>
On 01/28/2020 05:53 AM, Sourin Mondal (Vehere) wrote:
Hi Marcus,
I think my previous email is not sent properly so sending again.
Thanks for the information you provided. This 5 degrees is for what
frequency? Are you sure its 5 degrees or less? What is the precision?
Regards,
Sourin
The comp
Hi Marcus,
I think my previous email is not sent properly so sending again. Thanks for the
information you provided. This 5 degrees is for what frequency? Are you sure
its 5 degrees or less? What is the precision?
Regards,
Sourin
From: Marcus D. Leech
Sent: Mon
From: Marcus D. Leech
Sent: Monday, January 27, 2020 11:54 AM
To: Sourin Mondal (Vehere)
Cc: usrp-users@lists.ettus.com
Subject: Re: [USRP-users] phase-aligning two USRPs without Octoclock
On 01/27/2020 01:00 AM, Sourin Mondal (Vehere) wrote:
Hi Marcus,
Thanks
12 matches
Mail list logo
