[U-Boot] FSBBP: uboot Programming on to the flash for MPC8548 for bootup

ICH LOCATION I SHOULD FLASH THE UBOOT.BIN(SIZE IS NOT EQUAL TO 512) FOR Eg. If my uboot.bin size is >512K ? Please help me out in this. Regards, AJEESH KUMAR The information contained in this electronic message and any attachments to this message are intended for the exclusive use of

Re: [U-Boot] FSBBP: uboot Programming on to the flash for MPC8548 for bootup

Hi Andy, Thank you for your Info, so if my compiled output is <200k, my .bin file will easily fit into the boundary? Regards, AJEESH KUMAR -Original Message- From: Andy Fleming [mailto:[EMAIL PROTECTED] Sent: Tuesday, September 09, 2008 3:16 AM To: [EMAIL PROTECTED] Cc: u-b

[U-Boot] MPC8548: U-boot "Got error 4" while receiving packets

e earliest. Thanks & Regards Ajeesh Kumar ___ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot

[U-Boot] MPC8548 not able to detect Marvell 88E1145 PHY

cted in Configuration, and also in Four Independented Serial Management Mode. Please help me in this regard. Thanks, Ajeesh Kumar The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain

Re: [U-Boot] MPC8548 not able to detect Marvell 88E1145 PHY

interface will be fine. Actually, We are configuring the PHY chip have an address 0,1,2 and 3 but I dunno why I could read only the address 0x12?? Could you help me in giving the MUST required hardware configuration that should be done so as to make the PHY chip come up. Thanks, Ajeesh Kumar -Orig

Re: [U-Boot] MPC8548 not able to detect Marvell 88E1145 PHY

1.2 is several years old, so I wouldn't know where to >start, there. What do you mean by "the POR strappings for the 8548 are not set up to enable MDIO." I dint understand... Also, I've a similar hard ware as EP8548A board, with marvel 88E1145 E1 version.. Please let

Re: [U-Boot] Trouble moving custom MPC8548 board to U-boot 1.3

monitor code from the Flast to the ram. If this fails then it might be some problem in accessing ram. This happens when the LAW is not properly initialized and the memory is not mapped properly. Make sure you map ur DDR. Thanks, Ajeesh Kumar -Original Message- From: u-boot-boun...@lists.den

[U-Boot] scanf in u-boot.1.2.0

Hi All, I'm using a u-boot.1.2.0 code base, do we have a "scanf()" type of function call where i can use. Please help me in this regard. Thanks, Ajeesh Kumar The information contained in this electronic message and any attachments to this message are intended for the exclu

[U-Boot] Reset command on u-boot command line not working

* Figure out memory size in Megabytes. */ memsize = 512; /* * Establish Local Access Window and TLB mappings for DDR memory. */ memsize = setup_laws_and_tlbs(memsize); if (memsize == 0) { return 0; } return memsize * 1024 * 1024; } /**

Re: [U-Boot] Reset command on u-boot command line not working

of now, I have issues only in the reset. Please help me in this regard Thanks, Ajeesh Kumar -Original Message- From: Roman Mashak [mailto:romez...@gmail.com] Sent: Tuesday, January 27, 2009 6:46 PM To: aje...@tataelxsi.co.in Cc: Wolfgang Denk; u-boot@lists.denx.de; u-b...@avr32linux.org

Re: [U-Boot] Reset command on u-boot command line not working

Hello, I too got this info, but due to stipulated time, I cant shift to newer version now. I assumed that as development used the same u-boot thought of going with the same. Please help me. Thanks, Ajeesh Kumar -Original Message- From: Wolfgang Denk [mailto:w...@denx.de] Sent

Re: [U-Boot] Reset command on u-boot command line not working

Hi All, Reset problem got fixed, actually the reset command isn't doing a full board reset and just the core was regging resetted. Now its solved. Thanks a lot. Thanks, Ajeesh Kumar -Original Message- From: Jayakrishnan M [mailto:jay.krishn...@gmail.com] Sent: Tuesday, Janua

[U-Boot] MPC8548_eTSEC to Marvell 88E1145 E0 version Phy Initialization

phy_cmd[]){ /* shutdown */ {miim_end,} }, }; Thanks, Ajeesh Kumar The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidentia

[U-Boot] U-boot level MPC8548 Ethernet internal/External Loop back testing

Hi Wolfgang, We have a custom board with MPC8548E processor, please help me in suggesting/sharing Ethernet Internal/External Loopback testing code piece. Also any Phy level loop back too. Please do help me in this regard. Thanks, Ajeesh Kumar The information contained in this electronic