Move kernel and dtb name variable from headers to defconfig or
use default value from KConfig.
Signed-off-by: Fabien Lahoudere
---
configs/xilinx_zynqmp_zc1232_revA_defconfig | 2 ++
configs/xilinx_zynqmp_zc1254_revA_defconfig | 2 ++
configs/xilinx_zynqmp_zc1275_revA_defconfig
binaries in different places.
The two previous problem let me think that it can be easier to add
this information in the config file and have an entry in menuconfig
to define them, instead of patching source code.
This patch propose a solution.
Signed-off-by: Fabien Lahoudere
---
common/spl
In order to boot faster with falcon mode, we need to add SPL
support to riotboard.
Signed-off-by: Fabien Lahoudere
---
arch/arm/mach-imx/mx6/Kconfig | 1 +
board/embest/mx6boards/mx6boards.c | 48 ++
configs/riotboard_spl_defconfig| 48
From: Denis Zalevskiy
If there is an I2C mux, current bus should be switched before
manipulating with I2C.
Signed-off-by: Denis Zalevskiy
Signed-off-by: Fabien Lahoudere
---
drivers/bootcount/Kconfig | 15 -
drivers/bootcount/bootcount_i2c.c | 71
EPROM
where VPD is stored.
Signed-off-by: Denis Zalevskiy
Signed-off-by: Fabien Lahoudere
---
board/ge/common/vpd_reader.c | 20
configs/ge_bx50v3_defconfig | 18 ++
configs/mx53ppd_defconfig| 19 +++
include/configs/ge_bx50v3.h
From: Denis Zalevskiy
Use standard configuration logic to define EEPROM constants.
Names are based on VPD_EEPROM_ prefix because EEPROM_ is already
used by i2c_eeprom driver.
Signed-off-by: Denis Zalevskiy
Signed-off-by: Fabien Lahoudere
---
board/ge/bx50v3/Kconfig | 2 ++
board/ge
From: Denis Zalevskiy
Bootcount driver should verify size against the maximum available space.
New configuration parameter adds this capability and keeps backward
compatibility by providing default value.
Signed-off-by: Denis Zalevskiy
Signed-off-by: Fabien Lahoudere
---
drivers/bootcount
igned-off-by: Fabien Lahoudere
---
board/ge/bx50v3/bx50v3.c | 48 ++--
board/ge/common/vpd_reader.c | 37 +++---
board/ge/common/vpd_reader.h | 16 ++-
board/ge/mx53ppd/mx53ppd.c
GE boards need bootcount set in EEPROM instead of file to avoid some issues.
This series replace v2 sent by Sebastian Reichel on 2018-07-20.
Changes since v2:
- Patches have been rebased to apply correctly on master.
- Remove a build time warning
- Remove checkpatch.pl warning
Denis Zalevs
From: Denis Zalevskiy
The bus is statically defined, so remove redundant parameters
from read_vpd() for PPD and Bx50v3.
Signed-off-by: Denis Zalevskiy
Signed-off-by: Fabien Lahoudere
---
board/ge/bx50v3/bx50v3.c | 6 +++---
board/ge/mx53ppd/mx53ppd.c | 6 +++---
2 files changed, 6
) courtesy of incorrect initialization.
Signed-off-by: Dan Cimpoca
Signed-off-by: Fabien Lahoudere
---
board/ge/bx50v3/bx50v3.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
index 2eb1b65..2458525 100644
--- a/board/ge
From: Ian Ray
The b{4,6}50v3 kernel framebuffer console requires a modeline otherwise
the LVDS panel shows garbage.
Signed-off-by: Ian Ray
Signed-off-by: Fabien Lahoudere
---
board/ge/bx50v3/bx50v3.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge
From: Ian Ray
Use Video PLL to provide 65MHz for all displays.
Signed-off-by: Ian Ray
Signed-off-by: Fabien Lahoudere
---
board/ge/bx50v3/bx50v3.c | 30 +-
1 file changed, 17 insertions(+), 13 deletions(-)
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3
This patchset solves screen flickering observed at bootup on b650v3.
Steps to reproduce:
1) Connect B650 to power.
2) Switch On the Monitor.
3) Observe the display.
Ian Ray (2):
board: ge: bx50v3: correct LDB clock
board: ge: bx50v3: b{4,6}50v3 modeline
board/ge/bx50v3/bx50v3.c | 32 +++
While using ./scripts/get_maintainer.pl I detect that the Maintainer name
and address for bx50v3 boards are not valid.
The new maintainer for GE bx50v3 products must be Ian Ray.
Signed-off-by: Fabien Lahoudere
---
board/ge/bx50v3/MAINTAINERS | 2 +-
1 file changed, 1 insertion(+), 1 deletion
If the kernel is on an ext partition, we cannot load it because
spl_boot_mode() return MMCSD_MODE_RAW instead of MMCSD_MODE_FS.
Signed-off-by: Fabien Lahoudere
---
arch/arm/mach-imx/spl.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/mach-imx/spl.c b/arch/arm/mach
/extlinux.conf with for
example:
default Buildroot
label Buildroot
kernel /boot/zImage
append console=ttymxc1,115200 root=/dev/mmcblk0p1 rootwait rw
fdtdir /boot
Signed-off-by: Fabien Lahoudere
---
Changes for V2:
- reintegration of deleted env
- changes are applied only if
Hi Stefano,
Thank you for your comments.
On 13/07/2016 16:28, Stefano Babic wrote:
Hi Fabien,
On 29/06/2016 09:05, Fabien Lahoudere wrote:
In order to simplify the use of various images on various media
for nitrogen6x, the configuration of the board must follow the
generic distro
/extlinux.conf with for
example:
default Buildroot
label Buildroot
kernel /boot/zImage
append console=ttymxc1,115200 root=/dev/mmcblk0p1 rootwait rw
fdtdir /boot
Signed-off-by: Fabien Lahoudere
---
Changes for V2:
- reintegration of deleted env
- changes are applied
On 28/06/16 12:58, Sjoerd Simons wrote:
On Fri, 2016-06-24 at 17:59 +0200, Fabien Lahoudere wrote:
In order to simplify the use of various images on various media
for nitrogen6x, the configuration of the board must follow the
generic distro configuration (doc/README.distro).
In order to boot
/extlinux.conf with for
example:
default Buildroot
label Buildroot
kernel /boot/zImage
append console=ttymxc1,115200 root=/dev/mmcblk0p1 rootwait rw
fdtdir /boot
Signed-off-by: Fabien Lahoudere
---
Changes for V2:
- reintegration of deleted env
- changes are applied
On 27/06/16 20:51, Troy Kisky wrote:
On 6/24/2016 8:59 AM, Fabien Lahoudere wrote:
In order to simplify the use of various images on various media
for nitrogen6x, the configuration of the board must follow the
generic distro configuration (doc/README.distro).
In order to boot your old rootfs
/extlinux.conf with for
example:
default Buildroot
label Buildroot
kernel /boot/zImage
append console=ttymxc1,115200 root=/dev/mmcblk0p1 rootwait rw
fdtdir /boot
Signed-off-by: Fabien Lahoudere
---
configs/mx6qsabrelite_defconfig | 1 +
configs/nitrogen6dl2g_defconfig | 1
23 matches
Mail list logo
