Hi Simon,
> Da: Simon Glass
> Inviato: mercoledì 23 novembre 2022 03:09
>
> Hi Pegorer,
>
> On Sat, 19 Nov 2022 at 11:01, Pegorer Massimo
> wrote:
> >
> > Commit 87b0af9317cb4105f3f29cb0a4c28c7cd87ea65f added support for
> > signing auto-generated (mkimage -f auto) FIT. Unfortunately, this s
Hi,
On 23/11/22 14:34, Ashok Reddy Soma wrote:
From: T Karthik Reddy
The driver was using an incorrect value for GQSPI_LPBK_DLY_ADJ_DLY_1
tapdelay for Versal for frequencies above 100MHz. Change it from 2 to 1
based on the recommended value in IP spec.
Thanks, this looks much clearer ;)
Si
On 11/21/22 04:15, Jim Liu wrote:
Fix bug for npcm7xx bmc calculate pll clock.
PLLCON1 need to divide by 2.
Signed-off-by: Jim Liu
---
drivers/clk/nuvoton/clk_npcm7xx.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/clk/nuvoton/clk_npcm7xx.c
b/drivers/clk/nuvoto
On 11/22/22 03:05, Gabriel Fernandez wrote:
Add support of stm32mp13 DT bindings of clock and reset.
Signed-off-by: Gabriel Fernandez
Reviewed-by: Patrick Delaunay
---
(no changes since v1)
MAINTAINERS | 2 +
include/dt-bindings/clock/stm32mp13-clks.h
On 11/22/22 03:05, Gabriel Fernandez wrote:
STM32MP13 RCC driver uses Common Clock Framework and also a
'clk-stm32-core' API. Then STM32MPx RCC driver will contain only data
configuration (gates, mux, dividers and the way to check security)
or some specific clocks.
This API will be used by all ne
On 11/23/22 06:55, Marc Kleine-Budde wrote:
If the user select the image type "flat_dt" a FIT image will be build.
This breaks the legacy use case of putting a Flat Device Tree into a
legacy u-boot image.
Add a new image type "fdt_legacy" to build a legacy u-boot image
with a "flat_dt" type.
Li
From: Tien Fong Chee
Fixing debug log typo.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
drivers/ddr/altera/sdram_n5x.c | 12 ++--
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/ddr/altera/sdram_n5x.c b/drivers/ddr/altera/sdram_n5x.c
index 8a5f0
Hi Jerome,
On Wed, 23 Nov 2022 at 19:57, Jerome Forissier
wrote:
>
> Hi,
>
> On 11/23/22 08:17, Masahisa Kojima wrote:
> > eficonfig command reads the all possible UEFI boot options
> > from 0x to 0x to construct the menu. This takes too much
> > time in some environment, especially for t
Hi Heinrich,
On Wed, 23 Nov 2022 at 16:26, Heinrich Schuchardt wrote:
>
> On 11/23/22 08:17, Masahisa Kojima wrote:
> > eficonfig command reads the all possible UEFI boot options
> > from 0x to 0x to construct the menu. This takes too much
> > time in some environment, especially for the
> -Original Message-
> From: Dylan Hung
> Sent: Friday, November 11, 2022 3:30 PM
> To: Ryan Chen ; ChiaWei Wang
> ; j...@jms.id.au; Dylan Hung
> ; u-boot@lists.denx.de
> Cc: BMC-SW
> Subject: [PATCH 3/3] ram: ast2600: Align the RL and WL setting
>
> Use macro to represent the RL and WL
> -Original Message-
> From: Dylan Hung
> Sent: Friday, November 11, 2022 3:30 PM
> To: Ryan Chen ; ChiaWei Wang
> ; j...@jms.id.au; Dylan Hung
> ; u-boot@lists.denx.de
> Cc: BMC-SW
> Subject: [PATCH 2/3] ram: ast2600: Improve ddr4 timing and signal quality
>
> Adjust the following setti
> -Original Message-
> From: Dylan Hung
> Sent: Friday, November 11, 2022 3:30 PM
> To: Ryan Chen ; ChiaWei Wang
> ; j...@jms.id.au; Dylan Hung
> ; u-boot@lists.denx.de
> Cc: BMC-SW
> Subject: [PATCH 1/3] ram: ast2600: Fix incorrect statement of the register
> polling
>
> The condition "
ENTRY/ENDPROC macros from linux/linkage.h will make code more readable and
also will properly mark assembly symbol in ELF binary as function symbol.
Signed-off-by: Pali Rohár
---
board/nokia/rx51/lowlevel_init.S | 6 --
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/board/noki
On Wednesday 23 November 2022 18:15:17 Tom Rini wrote:
> On Wed, Nov 23, 2022 at 11:50:59PM +0100, Pali Rohár wrote:
> > On Tuesday 22 November 2022 12:31:56 Tom Rini wrote:
> > > It is a bad idea, and more modern toolchains will fail, if you declare
> > > an assembly function to be global and then
On Wed, Nov 23, 2022 at 11:50:59PM +0100, Pali Rohár wrote:
> On Tuesday 22 November 2022 12:31:56 Tom Rini wrote:
> > It is a bad idea, and more modern toolchains will fail, if you declare
> > an assembly function to be global and then weak, instead of declaring it
> > weak to start with. Update a
Commit 08574ed339fb ("Convert CONFIG_SYS_MONITOR_LEN to Kconfig") moved
the definition of said config variable from the common sunxi header to
*every board's* defconfig.
This is a platform choice, not board specific, so remove the variable
from there, instead set the one value for all Allwinner boa
On Tuesday 22 November 2022 12:31:56 Tom Rini wrote:
> It is a bad idea, and more modern toolchains will fail, if you declare
> an assembly function to be global and then weak, instead of declaring it
> weak to start with. Update assorted assembly files to use the WEAK macro
> directly.
>
> Signed
Hi Tom,
On Wed, Nov 23, 2022 at 5:45 AM Tom Rini wrote:
>
> On Tue, Nov 22, 2022 at 01:09:55PM -0800, Tony Dinh wrote:
> > Resend to include the mailing list!
> >
> > Tony
> >
> > On Tue, Nov 22, 2022 at 11:58 AM Tony Dinh wrote:
> > >
> > > Hi Tom,
> > >
> > > On Tue, Nov 22, 2022 at 9:32 AM To
Hi Michal,
On 23 Nov 2022, Michal Simek wrote:
>> On 11/23/22 04:14, Sean Anderson wrote:
>>> On 11/22/22 20:23, David Antliff wrote:
>>> Hi,
>>>
>>> I'm looking to extract the board's MAC address from serial I2C EEPROM at
>>> boot
>>> time, so
>>> I'm trying to work out how I can tell if U-Boot
Hi Sean, thank you for your reply.
On 23 Nov 2022, Sean Anderson wrote:
> On 11/22/22 20:23, David Antliff wrote:
> > My question is - is the 'i2c' command now the accepted and best way to
> > interact with an
> > I2C EEPROM? Or is there another command I can enable (other than "eeprom")
> > tha
On Tue, 22 Nov 2022 21:57:03 +0100
Giulio Benetti wrote:
Hi,
> On some board gpio to power LCD can be active low, so let's add
> CONFIG_VIDEO_LCD_POWER_ACTIVE_LOW to allow this.
This is all so very sadly outdated code, which could be all solved
very nicely by just looking at the DT.
Do you desc
On 11/23/22 18:16, John Keeping wrote:
It seems this symbol was missed when renaming DM_VIDEO -> VIDEO. Update
it.
Fixes: b86986c7b3 ("video: Rename CONFIG_DM_VIDEO to CONFIG_VIDEO")
Signed-off-by: John Keeping
Reviewed-by: Heinrich Schuchardt
---
cmd/Kconfig | 2 +-
1 file changed, 1
On Wed, Nov 23, 2022 at 07:22:52PM +0100, Pali Rohár wrote:
> On Wednesday 23 November 2022 13:18:40 Tom Rini wrote:
> > On Tue, Nov 08, 2022 at 09:52:22AM +0100, Max Krummenacher wrote:
> >
> > > From: Max Krummenacher
> > >
> > > With LTO enabled the U-Boot initial environment is no longer sto
On Wednesday 23 November 2022 13:18:40 Tom Rini wrote:
> On Tue, Nov 08, 2022 at 09:52:22AM +0100, Max Krummenacher wrote:
>
> > From: Max Krummenacher
> >
> > With LTO enabled the U-Boot initial environment is no longer stored
> > in an easy accessible section in env/common.o. I.e. the section
On Tue, Nov 08, 2022 at 09:52:22AM +0100, Max Krummenacher wrote:
> From: Max Krummenacher
>
> With LTO enabled the U-Boot initial environment is no longer stored
> in an easy accessible section in env/common.o. I.e. the section name
> changes from build to build, its content maybe compressed an
Add properties to the Authenta SPI flash device node to enable access by
a UEFI application using a fixed GUID.
Signed-off-by: Paul Barker
---
arch/arm/dts/am335x-sancloud-bbe-lite-u-boot.dtsi | 13 ++---
arch/arm/dts/am335x-sancloud-bbe-lite.dts | 2 +-
2 files changed, 11 inse
These tests ensure that the new UEFI SPI I/O protocol support works as
expected. They intended to execute on the sandbox target.
Signed-off-by: Paul Barker
---
MAINTAINERS | 1 +
arch/sandbox/dts/test.dts| 13 +
lib/efi_selftest/Makefile
This addition allows UEFI applications running under u-boot to access
peripherals on SPI busses. It is based on the UEFI Platform
Initialization (PI) Specification, Version 1.7 Errata A (April 2020).
Only the core functionality required to discover SPI peripherals and
communicate with them is curre
These patches add support for the UEFI SPI I/O protocol defined in the
UEFI Platform Initialization (PI) Specification, Version 1.7 Errata A
(April 2020). This allows a UEFI application to interact with devices
on the SPI bus.
This support is initially intended to be used to communicate with SPI
d
On Wed, Nov 23, 2022 at 03:08:23PM +0100, Neil Armstrong wrote:
>
> Hi Tom,
>
> Here's changes for next release:
> - Implement setbrg op to meson serial device
> - Re-add the old PHY reset binding for nanopi-k2
>
> The CI job is at
> https://source.denx.de/u-boot/custodians/u-boot-amlogic/pipe
It seems this symbol was missed when renaming DM_VIDEO -> VIDEO. Update
it.
Fixes: b86986c7b3 ("video: Rename CONFIG_DM_VIDEO to CONFIG_VIDEO")
Signed-off-by: John Keeping
---
cmd/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/cmd/Kconfig b/cmd/Kconfig
index 1092fb9
On Tue, Oct 11, 2022 at 19:57, neil.armstr...@linaro.org wrote:
> On 11/10/2022 18:36, Mattijs Korpershoek wrote:
>> On Tue, Oct 11, 2022 at 17:39, Marek Vasut wrote:
>>
>>> On 10/11/22 09:12, neil.armstr...@linaro.org wrote:
On 10/10/2022 19:16, Marek Vasut wrote:
> On 10/10/22 18:22,
With CONFIG_DM_USB_GADGET=y, we no longer need any board_usb_*() logic
because:
* the dwc2 driver is DM compatible, and handles its own clock enabling
* the dwc3-meson-g12a glue drivers handles "force mode switching"
Remove all mach-meson/g12a usb code and enable CONFIG_DM_USB_GADGET.
Note: Only
arch/mach-meson has some custom usb logic, in particular:
* on board_usb_init(), we force USB_DR_MODE_PERIPHERAL
* on board_usb_cleanup(), we force USB_DR_MODE_HOST
With DM_USB_GADGET=y, board_usb_init/cleanup() are no
longer used when we call usb_gadget_initialize().
Instead, the generic (from ud
While working on some USB bugs on the VIM3L board, we stumbled upon the fact
that mach-meson still uses legacy board_usb_*() functions instead of using DM
[1]
This series aim to switch the g12a based boards to use CONFIG_DM_USB_GADGET and
removes the board_usb_*() logic.
* The first patch adds m
Add support of generic IIO channels binding:
./devicetree/bindings/iio/adc/adc.yaml
Keep support of st,adc-channels for backward compatibility.
Signed-off-by: Olivier Moysan
---
drivers/adc/stm32-adc.c | 51 -
1 file changed, 45 insertions(+), 6 deletions
Split stm32_adc_chan_of_init channel initialization function into
several routines to increase readability and prepare channel
generic binding handling.
Signed-off-by: Olivier Moysan
---
drivers/adc/stm32-adc.c | 44 +++--
1 file changed, 34 insertions(+), 10
Add support of generic IIO channels binding:
./devicetree/bindings/iio/adc/adc.yaml
Keep support of legacy property st,adc-channels for backward compatibility.
However, the st,adc-channels property is deprecated, and generic channel
bindings should be used instead.
Mixing of generic and legacy p
Enable efuse support which allows reading of the cpuid#, serial#
and also generates a unique mac address from the board's serial.
Signed-off-by: Christopher Obbard
---
Changes in v2:
- added missing configuration symbol CONFIG_MISC_INIT_R=y
configs/roc-pc-mezzanine-rk3399_defconfig | 2 ++
conf
From: Yau Wai Gan
This enable the capability to automatically perform FPGA
configuration when booting Linux FIT image via bootm command.
The FPGA configuration bitstream shall be packed within the
FIT image.
Signed-off-by: Yau Wai Gan
Signed-off-by: Jit Loon Lim
---
drivers/fpga/altera.c | 41
On 11/23/22 10:11, Michal Simek wrote:
On 11/23/22 14:27, Michael Walle wrote:
ethernet {
nvmem-cells = <&mac_address>;
nvmem-cell-names = "mac-address";
};
You'll need 2022.07 for this I think. This is the same method which
Linux uses. I added this specificly to be able to load M
From: Tien Fong Chee
Klocwork reported the unvalidated integer value 'cal->header.data_len' is
used but this is not a issue because the proper value is calculated before
assigning 'cal->header.data_len' and CRC32 is generated before saving
this value into QSPI to ensure data integrity when readin
On 11/23/22 14:27, Michael Walle wrote:
ethernet {
nvmem-cells = <&mac_address>;
nvmem-cell-names = "mac-address";
};
You'll need 2022.07 for this I think. This is the same method which
Linux uses. I added this specificly to be able to load MAC addresses
from EEPROMs without needi
On Tue, Nov 22, 2022 at 07:13:03PM -0700, Simon Glass wrote:
> Hi Tom,
>
> The following changes since commit 521277ec15eb794229403ec24b8c00a4ff02b0b6:
>
> Merge tag 'xilinx-for-v2023.01-rc3' of
> https://source.denx.de/u-boot/custodians/u-boot-microblaze (2022-11-22
> 12:33:48 -0500)
>
> are
From: Tien Fong Chee
Klockwork reported there is potential value overflow with incorrect
typecast, but this is not valid in this arithmetic implementation because
result is never over 32-bit size. The code is improved to ensure correct
size of result returned with correct type casting for the sak
From: Tien Fong Chee
Ensure the PHY calibration data is copied to DDR only when DDR retention
is set.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
drivers/ddr/altera/sdram_n5x.c | 11 +++
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/drivers/ddr/altera
From: Tien Fong Chee
Return error immediately if invalid DDR type is detected in argument so
that uninitialized local variables such val and upd_val would not be used.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
drivers/ddr/altera/sdram_n5x.c | 3 +++
1 file changed, 3 inser
From: Tien Fong Chee
HSD #18016722456: Includes only required header for mdelay function.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
arch/arm/mach-socfpga/secure_vab.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/mach-socfpga/secure_vab.c
b/
From: Tien Fong Chee
DDR need to be initialized and running calibration if DDR init hang
before reset due to watchdog.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
drivers/ddr/altera/sdram_n5x.c | 30 ++
1 file changed, 22 insertions(+), 8 deletion
From: Tien Fong Chee
DDR need to be initialized and running calibration if DBE is triggered
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
drivers/ddr/altera/sdram_n5x.c | 33 -
1 file changed, 24 insertions(+), 9 deletions(-)
diff --git a/drive
From: Tien Fong Chee
The bit[30] of boot scratch cold 8 register is used as DDR init progress
tracking by SDM when watchdog is triggered due to ddr init hang, so that
SDM can run a clean reset to DDR subsystem.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
drivers/ddr/altera/s
From: Tien Fong Chee
The boot scratch cold reg 8 is shared between DBE, DDR init progress
update and Linux EDAC. This patch defines how the bits are used by
respective features above and their macro names used in U-Boot.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
.../includ
From: Tien Fong Chee
HSD #1308580006: Some compilers complaint implicit declaration of malloc
function, and some
compilers have no this issue. Adding malloc.h to resolve this issue.
Signed-off-by: Tien Fong Chee
Signed-off-by: Jit Loon Lim
---
arch/arm/mach-socfpga/secure_vab.c | 9 +
Hi Tom,
Here's changes for next release:
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
The CI job is at
https://source.denx.de/u-boot/custodians/u-boot-amlogic/pipelines/14199
Thanks,
Neil
The following changes since commit 536c642ffef545b4b5b
From: Ley Foon Tan
HSD #18016042797-2: Add mask support to INTEL_SIP_SMC_HPS_SET_BRIDGES SMC call.
Signed-off-by: Ley Foon Tan
Signed-off-by: Jit Loon Lim
---
arch/arm/mach-socfpga/reset_manager_s10.c | 10 +++---
include/linux/intel-smc.h | 14 ++
2 files chan
From: Ley Foon Tan
HSD #18016042797-1: The existing ignore the "mask" value when call to
socfpga_bridges_reset().
This patch add the mask support when bridge enable/disable.
Mask value:
BIT0: soc2fpga
BIT1: lwhps2fpga
BIT2: fpga2soc
These bridges available only in Stratix 10:
BIT3: f2sdram0
B
On Tue, Nov 22, 2022 at 01:09:55PM -0800, Tony Dinh wrote:
> Resend to include the mailing list!
>
> Tony
>
> On Tue, Nov 22, 2022 at 11:58 AM Tony Dinh wrote:
> >
> > Hi Tom,
> >
> > On Tue, Nov 22, 2022 at 9:32 AM Tom Rini wrote:
> > >
> > > With gcc-12.2 we now get:
> > > lib/zlib/inflate.c:
>> ethernet {
>> nvmem-cells = <&mac_address>;
>> nvmem-cell-names = "mac-address";
>> };
>>
>> You'll need 2022.07 for this I think. This is the same method which
>> Linux uses. I added this specificly to be able to load MAC addresses
>> from EEPROMs without needing to hard code stuff i
Hello,
the first patch cleans up the error message output if struct
image_type_params::set_header is set, the other adds support for
creating legacy images with type flat_dt.
regards,
Marc
Changes since v2:
- renamed new image type to "fdt_legacy" (suggested by Sean Anderson)
Changes since v1:
-
If the user select the image type "flat_dt" a FIT image will be build.
This breaks the legacy use case of putting a Flat Device Tree into a
legacy u-boot image.
Add a new image type "fdt_legacy" to build a legacy u-boot image
with a "flat_dt" type.
Link: https://lore.kernel.org/all/20221028155205
Hello,
the first patch cleans up the error message output if struct
image_type_params::set_header is set, the other adds support for
creating legacy images with type flat_dt.
regards,
Marc
Changes since v2:
- renamed new image type to "fdt_legacy" (suggested by Sean Anderson)
Changes since v1:
-
In case there's no struct image_type_params::set_header callback, no
"errno" will be set. Don't fail with an error message, followed by
"Success". Remove the printing of the human readable "errno" value.
Signed-off-by: Marc Kleine-Budde
---
tools/mkimage.c | 4 ++--
1 file changed, 2 insertions(
Reading MAC address from on board EEPROM requires different type for System
Controller (SC).
Signed-off-by: Michal Simek
---
board/xilinx/Kconfig | 9 +
board/xilinx/common/fru.h | 1 +
board/xilinx/common/fru_ops.c | 6 +-
3 files changed, 15 insertions(+), 1 deletion(
The handle "fd" was created in fdtgrep.c:708 by calling the
"open" function and is lost in fdtgrep.c:716 and fdtgrep.c:723.
Close file descriptor 'fd' before exiting with an error from function
utilfdt_read_err_len(const char *filename, char **buffp, off_t *len).
Fixes: 1043d0a0296a ("fdt: Add
The handle "fd" was created in imx8image.c:249 by calling the "fopen"
function and is lost in imx8image.c:282.
Should close the 'fd' file descriptor before exiting the
parse_cfg_file(image_t *param_stack, char *name) function.
Fixes: a2b96ece5be1 ("tools: add i.MX8/8X image support")
Signed-of
Hi,
On 11/23/22 08:17, Masahisa Kojima wrote:
> eficonfig command reads the all possible UEFI boot options
> from 0x to 0x to construct the menu. This takes too much
> time in some environment, especially for the platform using
> OP-TEE and RPMB based secure storage.
> For example, on Soci
The handle "fd" was created in imx8mimage.c:178 by calling
the "fopen" function and is lost in imx8mimage.c:210.
Should close the 'fd' file descriptor before exiting
the parse_cfg_file(char *name) function.
Fixes: 6609c2663c9c ("tools: add i.MX8M image support")
Signed-off-by: Mikhail Ilin
--
The copy_datafile(ifd, params.datafile) function has been
implemented to copy data by reducing the number of lines in the main
function.
Signed-off-by: Mikhail Ilin
---
tools/mkimage.c | 35 +++---
1 file changed, 20 insertions(+), 15 deletions(-)
diff --git a/too
From: T Karthik Reddy
The driver was using an incorrect value for GQSPI_LPBK_DLY_ADJ_DLY_1
tapdelay for Versal for frequencies above 100MHz. Change it from 2 to 1
based on the recommended value in IP spec.
Signed-off-by: T Karthik Reddy
Signed-off-by: Ashok Reddy Soma
---
Changes in v2:
- Up
Hi Dhruva,
> -Original Message-
> From: Dhruva Gole
> Sent: Wednesday, November 23, 2022 1:34 PM
> To: Soma, Ashok Reddy ; u-
> b...@lists.denx.de
> Cc: ja...@amarulasolutions.com; Simek, Michal ;
> g...@xilinx.com; git (AMD-Xilinx) ; T Karthik Reddy
>
> Subject: Re: [PATCH] spi: zynqmp_
On 23.11.22 09:06, Mikhail Ilin wrote:
If memory allocation fails on line 780, then 'fail' will be
jumped to and 'ptr' will be null, causing it to be dereferenced it on line
855. Thus, before using 'ptr[i]' one must make sure that the 'ptr' pointer
is not NULL.
Nitpicking. You seem to h
On 11/23/22 04:14, Sean Anderson wrote:
On 11/22/22 20:23, David Antliff wrote:
Hi,
I'm looking to extract the board's MAC address from serial I2C EEPROM at boot
time, so
I'm trying to work out how I can tell if U-Boot is actually able to
communicate with this
EEPROM, outside of manual i2
The commit ba74bcf3e07b ("xilinx: common: Remove
zynq_board_read_rom_ethaddr()") removed zynq_board_read_rom_ethaddr()
because xlnx,eeprom link via DT chosen node is no longer used. But forget
to remove Kconfig entries which are used by this code only.
Signed-off-by: Michal Simek
---
board/xili
If memory allocation fails on line 780, then 'fail' will be
jumped to and 'ptr' will be null, causing it to be dereferenced it on line
855. Thus, before using 'ptr[i]' one must make sure that the 'ptr' pointer
is not NULL.
Fixes: 934b14f2bb30 ("ext4: free allocations by parse_path()")
Signed-o
On 23/11/22 11:36, Ashok Reddy Soma wrote:
From: T Karthik Reddy
Update GQSPI_LPBK_DLY_ADJ_DLY_1 tapdelay value for Versal for
frequencies above 100MHz.
Please can you help me understand why this was needed to be updated?
If there was some bug/ anomally with 0x2 then can you describe why
75 matches
Mail list logo
