m
>
> CA Lic. 773985
>
>
>
>
>
> *From:* Jason Szumlanski [mailto:ja...@floridasolardesigngroup.com]
> *Sent:* Wednesday, March 27, 2024 3:52 PM
> *To:* Kirk Herander
> *Cc:* William Miller; RE-wrenches
> *Subject:* Re: [RE-wrenches] Sol-Ark 15K AC Output
>
>
12:38 PM
*To:* RE-wrenches; will...@millersolar.com
*Cc:* Jason Szumlanski
*Subject:* Re: [RE-wrenches] Sol-Ark 15K AC Output
www.interlockkit.com - they stock and custom make interlock bypasses
including multiple breakers.
Square D also makes a 400 A panel which excepts either bolt on or snap
gt;
>> *Owner|Principal, VT Solar, LLC*
>>
>> *Celebrating our 33st Anniversary 1991-2024!!*
>>
>> dba Vermont Solar Engineering
>>
>> 802.559.1225
>>
>>
>>
>>
>>
>> On Wed, Mar 27, 2024 at 3:15 PM William Miller via RE-wrenches <
>
eone out there.
> That’s why we do it.
>
>
>
> Wm
>
>
>
> Miller Solar
>
> 17395 Oak Road, Atascadero, CA 93422
>
> 805-438-5600
>
> www.millersolar.com
>
> CA Lic. 773985
>
>
>
>
>
> *From:* Kirk Herander [mai
*Subject:* Re: [RE-wrenches] Sol-Ark 15K AC Output
www.interlockkit.com - they stock and custom make interlock bypasses
including multiple breakers.
Square D also makes a 400 A panel which excepts either bolt on or snap on
QO breakers.
*Kirk Herander / **kirkh@vermont.solar *
*Owner
, Atascadero, CA 93422
>
> 805-438-5600
>
> www.millersolar.com
>
> CA Lic. 773985
>
>
>
>
>
> *From:* Jason Szumlanski [mailto:ja...@floridasolardesigngroup.com]
> *Sent:* Wednesday, March 27, 2024 3:12 AM
> *To:* will...@millersolar.com
> *Cc:* RE-wrenches
> *Su
*Subject:* Re: [RE-wrenches] Sol-Ark 15K AC Output
William,
Thanks for the information on grid peak shaving. That is what I thought
could be done. The description is a misnomer of sorts (like a lot of things
in Sol-Ark lingo). It's a bit hard to follow and not nearly well
enough docum
> > >
> > > PS: Below is a diagram on how to provide bypass. I tried to depict the
> > > bypass interlock graphically. The point is you cannot turn on the bypass
> > > breaker without turning off the inverter output breakers. See photos of
> > > the actual hardware on the web page linked b
ware on the web page linked below. I find bypass
>> very handy because if there is an inverter or battery failure the client
>> can restore power immediately and I can respond at a more convenient time.
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> Wm
>>
&g
ass
>> very handy because if there is an inverter or battery failure the client
>> can restore power immediately and I can respond at a more convenient time.
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> Wm
>>
>>
>>
>> Mil
Wrenches, Jason
I have always either with outback and with solark have always connected
each unit with a distribution panel with breakers regardless of what's in
the inverter package. This same goes for the gen set connections with
proper breakers so not to have to over size the wires.
I have conne
#4 wire as the output of each inverter is definitely not adequate, as each
inverter can pass through 150A of generator power. In theory it would be
spit across all four, but that doesn't matter. It's an open spigot, so at a
minimum the output conductors would need to be 150A rated in my opinion.
Th
Hi Dave,
XW inverters do a decent job of explaining generator support mode where
small generators can be supplemented by inverter power to start up large
loads. I believe several other brands can do this, and I believe Sol-Ark is
one of them. But front line customer service wasn't really up to spe
Jason:
I am wondering on the advisability of hardwiring the outputs of all four
inverters together. If one inverter fails the other three can backfeed
into it without any means to disconnect the failed inverter and without
over-current protection. Have you considered landing the output of each
I may be wrong, but I was under the impression that most inverter/chargers
are either being an inverter or a charger at any given time, but not both.
So, once the inverter sees the AC voltage from the generator, then it will
switch to being a charger and use the generator AC power to charge the
bat
15 matches
Mail list logo
