From: Chris R Blake
This patch is to add support for qca955x_eth_rx_delay
to work with the qca955x SoC.
Signed-off-by: Chris R Blake
---
...42-MIPS-ath79-add-qca955x-mac-tx-rx-delay.patch | 58 ++
1 file changed, 58 insertions(+)
create mode 100644
target/linux/ar71xx
From: Chris R Blake
This patch is to add support for sgmii/serdes calibration from
within the OpenWRT environment. This is needed on boards that
do not use u-boot or do not have a pre-init process that runs
calibration.
Signed-off-by: Chris R Blake
---
...S-ath79-add-qca955x-mac-sgmii
From: Chris R Blake
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake
---
package/base-files/files/etc/init.d/led| 2 +-
.../linux/ar71xx/files/drivers/leds/leds-nu801.c | 396 +
.../linux/ar71xx
From: Chris R Blake
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake
---
package/base-files/files/lib/function
From: Chris R Blake
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake
---
package/base-files/files/etc/rc.b
From: Chris R Blake
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake
---
package/base-files/files/etc/init.d/led| 2 +-
.../linux/ar71xx/files/drivers/leds/leds-nu801.c | 396 +
.../linux/ar71xx
From: Chris R Blake
This patch is to add support for qca955x_eth_rx_delay
to work with the qca955x SoC.
Signed-off-by: Chris R Blake
---
...42-MIPS-ath79-add-qca955x-mac-tx-rx-delay.patch | 58 ++
1 file changed, 58 insertions(+)
create mode 100644
target/linux/ar71xx
From: Chris R Blake
This patch is to add support for sgmii/serdes calibration from
within the OpenWRT environment. This is needed on boards that
do not use u-boot or do not have a pre-init process that runs
calibration.
Signed-off-by: Chris R Blake
---
...S-ath79-add-qca955x-mac-sgmii
From: Chris R Blake
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1
Signed-off-by: Chris R Blake
---
target/linux/ar71xx/files/arch/mips/ath79/dev-m25p80.c | 8
From: Chris R Blake
This patch is to add support for the AirTight Networks C-55 Access Point
Signed-off-by: Chris R Blake
---
target/linux/ar71xx/base-files/etc/diag.sh | 3 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 8 ++
.../ar71xx/base-files/etc/uci-defaults/01_leds
From: Chris R Blake
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake
---
package/base-files/files/lib/function
From: Chris R Blake
This patch is to add support for qca955x_eth_rx_delay
to work with the qca955x SoC.
Signed-off-by: Chris R Blake
---
...42-MIPS-ath79-add-qca955x-mac-tx-rx-delay.patch | 58 ++
1 file changed, 58 insertions(+)
create mode 100644
target/linux/ar71xx
From: Chris R Blake
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake
---
package/base-files/files/etc/init.d/led| 2 +-
.../linux/ar71xx/files/drivers/leds/leds-nu801.c | 396 +
.../linux/ar71xx
From: Chris R Blake
This patch is to add support for sgmii/serdes calibration from
within the OpenWRT environment. This is needed on boards that
do not use u-boot or do not have a pre-init process that runs
calibration.
Signed-off-by: Chris R Blake
---
...S-ath79-add-qca955x-mac-sgmii
14 matches
Mail list logo
