Hi all,
I just recently purchased a brand new HP Pavilion
G3035L Desktop PC (spec:
http://www.anugrahpratama.com/product/21/1092/HP-Pavilion-G3035L-Desktop-PC).
It's using Intel Core Duo processor. I tried to
install OpenBSD's latest snapshot to this machine last
night. The thing is it freezes
anyone knows about IBM xSeries 3550? I checked on
http://www.openbsd.org/i386.html and I saw that IBM xSeries 3550 were listed a
few times.
I am also looking to buy a U1 server, and I'm looking at either IBM xSeries
3550 or a Dell PowerEdge 1950. Anyone has any experience with these machines?
Hi all,
I'm looking to buy a server that supports OpenBSD and I'm looking at either
Dell PowerEdge 1950 III
or Dell PowerEdge R200. I noticed Marco (marco@)'s message about Dell PERC 6i
that exists on
PowerEdge 1950 III and R2000. But, if I'm not going to use RAID and only use
Serial ATA hard
Great, thanks for the info. This is my first time to get a rackmount server,
and I just wanna make sure
it is supported by OpenBSD ;)
As "Juan Miscaro" described on Wed, Jan 30, 2008 at 02:48:19PM -0500:
>
> --- Reza Muhammad <[EMAIL PROTECTED]> wrote:
>
> >
Hey guys,
Im having a problem with my bridge at home (running 4.0-current). I noticed
that after the RTSP update on cvs, the bridge connection that transferring data
in local network can only go up to 60 KB/s. I didn't change any of my settings
though. Is this an expected behaviour? Btw, he
--- Greg Thomas <[EMAIL PROTECTED]> wrote:
> On 1/23/07, sonjaya <[EMAIL PROTECTED]> wrote:
> > Dear All
> >
> > Any posible way to using 2 gateway in n out
> without using routed
> > protcol such as bgp/osf
> > Because i have two connection to Internet
> > basic diagram
> > |-gw01
Dear Lists.
I have one bridge PF machine for packet queue and
prio,
and few new install Mandriva2007 (linux kernel) that
couldn not browse the web (the other protocol work OK)
if the rules keep state in PF machine is activated.
but the others hosts (WinXP, BSD, Mac, Others Linux)
work fine.
Why P
--- Stuart Henderson <[EMAIL PROTECTED]> wrote:
> On 2007/01/28 19:56, Reza Muhammad wrote:
> > and few new install Mandriva2007 (linux kernel)
> that
> > couldn not browse the web (the other protocol work
> OK)
> > if the rules keep state in PF machine is
>
Hi all,
I was just trying to setup an ntpd server for my home network so it could sync
with each other. So here's what I have in my /etc/ntpd.conf:
# $OpenBSD: ntpd.conf,v 1.7 2004/07/20 17:38:35 henning Exp $
# sample ntpd configuration file, see ntpd.conf(5)
# Addresses to listen on (ntpd do
d to connect to the Internet directly from my laptop, the connection
is fine. Would a tcpdump log be
any helpful at this point?
Thanks for replying though.
On Wed, 26 Sep 2007 15:55:21 +0200, knitti <[EMAIL PROTECTED]> wrote:
> On 9/22/07, Reza Muhammad <[EMAIL PROTECTED]> wrote:
&
and there's still more. I noticed that the traffic coming in from 192.168.*.*
aren't from my local network.
On Wed, 26 Sep 2007 17:19:05 +0100, Stuart Henderson <[EMAIL PROTECTED]> wrote:
> On 2007/09/26 22:32, Reza Muhammad wrote:
>> Would a tcpdump log be any he
> On Wed, 26 Sep 2007 11:37:28 -0700, "Can E. Acar" <[EMAIL PROTECTED]>
> wrote:
>> Reza Muhammad wrote:
...
> also
>
> There is a lot of external broadcast traffic they are probably the cause
> of
> the large number of state insertions/deletions. They ar
thanks alot. I've created a new rulesets for my pf.conf, and it improves so
much. :)
On Thu, 27 Sep 2007 06:04:49 +0100, Stuart Henderson <[EMAIL PROTECTED]> wrote:
> On 2007/09/27 11:51, Reza Muhammad wrote:
>> > On Wed, 26 Sep 2007 11:37:28 -0700, "Can
Dear list.
My pf.conf not working.
I have pf in bridge machine with xl2 to internet
firewall and xl1 to
internal switch. Bridging is ok.
This my simple pf.conf
me="172.16.0.228"
altq on xl1 bandwidth 100% cbq queue {me,dflt}
queue mebandwidth 8Kb
queue dflt bandwidth 16Kb cbq (d
Dear All.
I start with the simple rule set in my pf bridge
machine to limit
bandwidth 3Mbps from my server on lan to internet and
from internet to
my server on lan
my_server_on_lan="172.16.0.228"
internet="202.x.x.x"
lan = "172.16.0.0/16"
altq on xl1 bandwidth 100% cbq queue \
{int_out,dflt_out
Hi list..
My rule set still not working, as i'm expected to
limit outgoing and incoming traffic pass to my pf
machine act as an bridge .
altq on xl1 bandwidth 100% cbq queue
{int_out,dflt_out}
queue int_out bandwidth 3Mb
queue dflt_out bandwidth 16Kb cbq (default)
altq on xl2 bandwi
Hi guys,
I have an OpenBSD router at home and the clients are connected
through a wired interface (fxp0) as well as wireless interface (ral0
running in HostAP mode). Previously, wired network has a different
network then the wireless network, wired network has the address of
192.168.1.0/
Actually I do. Clients are able to connect to the router, as well as
the Internet (I use NAT). However, clients cannot communicate to
other clients. For example, ip 192.168.1.2 (connected through wired
interface) and ip 192.168.1.3 (connected through wireless interface)
are the clients.
Dear All,
Is there any trick to optimize squid in OpenBSD ?
please give me hint.
regards
reza
Sell on Yahoo! Auctions no fees. Bid on great items.
http://auctions.yahoo.com/
dear All,
In which file should i put my static route entry ?
regards
reza
Start your day with Yahoo! - make it your home page
http://www.yahoo.com/r/hs
I problem with squid diskd in 3.7 GENERIC.
diskd process seem hang, when i restart squid. with
this error:
assertion failed:
/usr/ports/www/squid/w-squid-2.5.STABLE9/squid-2.5.STABLE9/src/fs/diskd/store_io_diskd.c:494:
"++send_errors < 100"
should i recompile new kernel to tunning message
queue.
Hi misc,
Please mind my stupidity for asking this. I'm trying to replace my
802.11b wireless card with the 802.11g card on my openbsd box. I think
im going to go with either the ath driver or ral since I want it to
run on hostap mode. However, I just bought a D-Link G520 (Hardware
rev: b3) and i
Thanks for the help. I guess I'll have to check the store myself.
It'll be too risky buying online. If I still can't get it right, I
might as well order from kd85.
Thanks again :)
> When I bought mine the version was on the box. It's not obvious, but
> it's located on a small sticker along wit
Dear All
"C Compiler cannot create executable" ?
what does it mean ?
My system is OpenBSD-3.8 Generic Kernel at Intel
Pentium M Proc 1600 Mhz (IBM Think Pad T41)
Please help ...
regards
reza
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
--- Stuart Henderson <[EMAIL PROTECTED]> wrote:
> > "C Compiler cannot create executable" ?
> > what does it mean ?
> > My system is OpenBSD-3.8 Generic Kernel at Intel
> > Pentium M Proc 1600 Mhz (IBM Think Pad T41)
>
> You should repost, including this information:
>
> what you were trying to
--- Jens Teglhus Mxller <[EMAIL PROTECTED]> wrote:
> On Wed, December 21, 2005 12:06, Reza Muhammad said:
> > Dear All
> >
> > "C Compiler cannot create executable" ?
> > what does it mean ?
> > My system is OpenBSD-3.8 Generic Kernel at Int
AFAIK, Squid (or other sevice) in your firewall which
need access to internet will looking for default
routing table, that in this case (pf load balance), u
dont have to specify it.
regards
reza
--- "MegadetH (crazyJM)" <[EMAIL PROTECTED]>
wrote:
> Hi all, I have a problem (very simple) with the
Hey guys, I'm having problem with ral0 running in hostap mode on my
openbsd box (i386, running 3.8-stable).
At the moment, the ral0 device acts as an access point and only using
mac address filtering to be able to go on the internet. So I don't
use the WEP, or IPSec, or anything like that.
Hi guys,
I was just updating my source tree through cvsup, and I've been
following -current for a while. There hadn't been any problems
before. But today, make build returned errors. The last time I
cvsup'd was today around 10pm (GMT +7), and here's some of the log:
Edit src/sys/arch/
29 matches
Mail list logo
