Hi Daniel,
On Sat, Sep 27, 2014 at 5:54 AM, Daniel Drake wrote:
> Hi,
it's always good to keep the relevant mailing list also in CC (linux-usb).
Also added Alan here.
>
> Booting 3.17-rc6 on ODROID-U2, I see this message:
>
> ERROR: Bad of_node_put() on /ehci@1258/port@1
> CPU: 0 PID: 1 Co
> Subject: Re: [PATCH v6 07/12] usb: chipidea: add a usb2 driver for ci13xxx
>
> On Tuesday 30 September 2014 20:39:34 Peter Chen wrote:
> > Thanks, Arnd. I had not thought setting dma mask is so complicated,
> > yes, it should check the return value, two things to confirm:
> >
> > - dma_coerce_
The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang
---
drivers/net/usb/r8152.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index 18b9e0d..604ef21 100644
--- a/drivers/net/usb/r
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed b
The patches fix the issues when the firmware exists.
For the multiple OS, the firmware may be loaded by the
driver of the other OS. And the Linux driver has influences
on it.
Hayes Wang (2):
r8152: remove clearing bp
r8152: disable power cut for RTL8153
drivers/net/usb/r8152.c | 30 ++--
Hello.
On 09/30/2014 01:51 PM, Yoshihiro Shimoda wrote:
This driver supports other SoCs, but they need boards/Soc depend code.
So, this patch adds device tree support for R-Car H2 and M2 initially.
Signed-off-by: Yoshihiro Shimoda
Acked-by: Kuninori Morimoto
---
drivers/usb/renesas_usbh
From: Hayes Wang
Date: Tue, 30 Sep 2014 16:48:01 +0800
> The flag of RTL8152_UNPLUG should only be set when the device is
> unplugged, not each time the rtl8152_disconnect() is called.
> Otherwise, the device wouldn't be stopped normally.
>
> Signed-off-by: Hayes Wang
Applied, thanks.
--
To un
Am Tue, 23 Sep 2014 23:09:25 +0200
schrieb Daniel van Gerpen :
> my RDF-8 card reader does not establish a super-speed connection when
> connected to an U3S6 USB3.0 port. It only manages high-speed:
[..]
Problem was not kernel related. Fixed by changing the BIOS Option
for PCI Express Frequency f
On Tue, 30 Sep 2014, Naveen Kumar Parna wrote:
> Hi Alan,
>
> > The device replied with a STALL.
> > The device runs at low speed or full speed and is connected through a USB-2
> > hub
>
> Yes, my device is full speed (12Mbps) device and connected to 2.0 root
> hub. So how to avoid getting the
On Mon, Sep 29, 2014 at 11:48:41PM -0500, Felipe Balbi wrote:
> Hi,
>
> On Tue, Sep 30, 2014 at 11:12:55AM +0800, Huang Rui wrote:
> > > > > > > > > On Thu, Sep 25, 2014 at 03:21:46PM +0800, Huang Rui wrote:
> > > > > > > > > > diff --git a/drivers/usb/dwc3/core.c
> > > > > > > > > > b/drivers/us
On Tuesday 30 September 2014 20:39:34 Peter Chen wrote:
> Thanks, Arnd. I had not thought setting dma mask is so complicated, yes, it
> should check the return value, two things to confirm:
>
> - dma_coerce_mask_and_coherent or dma_set_mask_and_coherent, the only
> difference
> of these two API i
On Tue, Sep 30, 2014 at 12:03:42PM +0200, Arnd Bergmann wrote:
> On Tuesday 30 September 2014 08:12:07 Peter Chen wrote:
> > > +
> > > + if (dev->of_node) {
> > > + ret = ci_hdrc_usb2_dt_probe(dev, ci_pdata);
> > > + if (ret)
> > > + goto clk_err;
> >
t;
> Signed-off-by: Arnd Bergmann
> Fixes: d115837259ada ("usb: host: ohci-st: Add OHCI driver support for ST STB
> devices")
> Cc: Greg Kroah-Hartman
> Cc: Peter Griffin
> Cc: Alan Stern
> Cc: linux-usb@vger.kernel.org
This became commit 905e300e1043 ("USB: host:
On Thu, Sep 25, 2014 at 05:47:11AM +, Muthu Mani wrote:
> > -Original Message-
> > From: Johan Hovold [mailto:jhov...@gmail.com] On Behalf Of Johan Hovold
> > > +static int cy_gpio_direction_input(struct gpio_chip *chip,
> > > + unsigned offset) {
>
On Tue, Sep 30, 2014 at 01:08:29PM +0200, Johan Hovold wrote:
> On Thu, Sep 25, 2014 at 11:21:58AM +0530, Muthu Mani wrote:
> > +static int cy_gpio_direction_input(struct gpio_chip *chip,
> > + unsigned offset)
> > +{
> > + return 0;
> > +}
> > +
> > +static int
On Thu, Sep 25, 2014 at 11:21:58AM +0530, Muthu Mani wrote:
> Adds support for USB-GPIO interface of Cypress Semiconductor
> CYUSBS234 USB-Serial Bridge controller.
>
> The GPIO get/set can be done through vendor command on control endpoint.
>
> Details about the device can be found at:
> http://
On Thu, Sep 25, 2014 at 11:21:15AM +0530, Muthu Mani wrote:
> Adds support for USB-I2C interface of Cypress Semiconductor
> CYUSBS234 USB-Serial Bridge controller.
>
> The read/write operation is setup using vendor command through control
> endpoint
> and actual data transfer happens through bulk
On Thu, Sep 25, 2014 at 05:46:16AM +, Muthu Mani wrote:
> > > +static int cy_i2c_xfer(struct i2c_adapter *adapter,
> > > +struct i2c_msg *msgs, int num) {
> > > + int ret = 0;
> > > + struct cyusbs_i2c *cy_i2c;
> > > + struct cyusbs23x *cyusbs = (struct cyusbs23
On Monday 29 September 2014 22:21:59 Sergei Shtylyov wrote:
> +
> + usb@0,1 {
> + reg = <0x800 0 0 0 0>;
> + device_type = "pci";
> + phys = <&usb0 0>;
> + phy-names = "usb";
> + };
>
On Tuesday 30 September 2014 08:12:07 Peter Chen wrote:
> > +
> > + if (dev->of_node) {
> > + ret = ci_hdrc_usb2_dt_probe(dev, ci_pdata);
> > + if (ret)
> > + goto clk_err;
> > + } else {
> > + ret = dma_set_mask_and_coherent(&pdev->de
Hello.
(2014/09/30 1:35), Sergei Shtylyov wrote:
> Hello.
>
> On 09/03/2014 09:25 AM, Yoshihiro Shimoda wrote:
>
>> This driver supports other SoCs, but they need boards/Soc depend code.
>> So, this patch adds device tree support for R-Car H2 and M2 initially.
>
>> Signed-off-by: Yoshihiro Shim
On Tue, 30 Sep 2014 14:10:28 +0800
"Lu, Baolu" wrote:
> On 9/30/2014 5:03 AM, Mark Knibbs wrote:
> > Great. I hope someone else is motivated to reproduce the issue. It will
> > take a long time for me to bisect due to my slow computer.
> Hi Mark,
>
> I tried to reproduce this issue. I connected
The device tree is here:
root@naveen-OptiPlex-745:/home/naveen# lsusb -t
1-1.5.2:1.2: No such file or directory
1-1.5.3:1.2: No such file or directory
1-1.5.4:1.2: No such file or directory
1-1.5.5:1.2: No such file or directory
1-1.5.6:1.2: No such file or directory
1-1.5.7.1:1.2: No such f
On Thu, Sep 25, 2014 at 11:20:12AM +0530, Muthu Mani wrote:
> Adds support for USB-I2C/GPIO interfaces of Cypress Semiconductor
> CYUSBS234 USB-Serial Bridge controller.
>
> Details about the device can be found at:
> http://www.cypress.com/?rID=84126
>
> Signed-off-by: Muthu Mani
> Signed-off-b
On Tue, 30 Sep 2014 14:10:28 +0800
"Lu, Baolu" wrote:
> I tried to reproduce this issue. I connected a USB key under a
> full-speed hub.
>
> sg_rbuf returns error which I am not familiar with.
>
> allen@allen-ivb:~$ lsusb -t
> [...snip...]
> /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehc
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang
---
drivers/net/usb/r8152.c | 6 +-
1 file changed, 5 insertions(+), 1 deletion(-)
diff
26 matches
Mail list logo
