xmp (disabled)
/sys/class/rc/rc0/protocols protocol imon (disabled)
/sys/class/rc/rc0/protocols protocol lirc (enabled)
Table for gpio_ir_recv, rc-rc6-mce not found. Keep as-is
like if rc-rc6-mce was not available anymore ?
Have a good day,
Frederic
Le 24/05/2019 à 06:12, Frédéric Deghetto a
Good day,
Information on the system:
- Raspberry 3b+
- Updated yesterday to 4.19.42-v7+
Before the update the remote control was working well with:
- gpio-rc-recv rc-rc6-mce kodi (into the file rc_maps.cfg)
- And the following data into /etc/rc_keymaps/kodi:
# table kodi, type: NEC
0
Dear Sakari et al.,
The acpi tables are apparently too big for the mailing lists.
So I put the file here:
https://mycore.core-cloud.net/index.php/s/DwTOb8TJJZYJtNe
Any information on what is going on with the webcams will be appreciated.
Thanks,
Frédéric
Or drivers. And a bit more than
for your help!
Frédéric
:~$ lspci
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v6/7th Gen Core
Processor Host Bridge/DRAM Registers (rev 02)
00:02.0 VGA compatible controller: Intel Corporation HD Graphics 620
(rev 02)
00:04.0 Signal processing controller: Intel Corporation Skylake
Hi Philipp,
Le 22/12/2014 17:00, Philipp Zabel a écrit :
The encoder needs to know the nominal framerate for the constant bitrate
control mechanism to work. Currently the only way to set the framerate is
by using VIDIOC_S_PARM on the output queue.
Signed-off-by: Philipp Zabel
---
drivers/medi
Hi Philipp,
Le 18/12/2014 17:52, Philipp Zabel a écrit :
Hi Frédéric,
Am Donnerstag, den 18.12.2014, 17:44 +0100 schrieb Frédéric Sureau:
Hi
I am trying to use the coda encoder through Gstreamer on an iMX6-based
board.
I use the (rebased and slightly modified) gstv4l2h264enc plugin from
Hi
I am trying to use the coda encoder through Gstreamer on an iMX6-based
board.
I use the (rebased and slightly modified) gstv4l2h264enc plugin from:
https://github.com/hizukiayaka/gst-plugins-good
This pipeline works fine:
gst-launch-1.0 -vvv v4l2src device=/dev/video4 !
"video/x-raw,width
/linuxtv.org/media_build.git
cd media_build
./build
And that's where the error occurs
I can't go farther.
Thanks for helping
Best regards
Frédéric Bernard
F92400 Courbevoie
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a me
Le mercredi 14 novembre 2012, Frédéric a écrit :
> I had a look at your patches. I don't see the '.fw_version' param anymore
> in the 'ngene_info' structure... Is it normal?
I also noticed some differences in the PLL presets:
In your patch:
.entries = {
add support for Thomson DTT7520X :
> 5fb67074c6657edc34867cba78255b6f5b505f12
I had a look at your patches. I don't see the '.fw_version' param anymore in
the 'ngene_info'
structure... Is it normal?
--
Frédéric
--
To unsubscribe from this list: send the line "un
y first driver contact), nor a DVB-T user (so far!), so a lot of
things are not clear
to me.
Thanks for reading.
¹ first time w_scan is launched, these lines take 2-3 seconds, and I guess this
is when the
drxd kernel messages are output.
--
Frédéric
--
To unsubscribe from this list: se
Not sure if it's the right place to report it.
At least here, v4l-utils doesn't compile if i2c-tools is installed,
because the latter installs a i2c-dev.h, like the kernel does with make
headers_install, but which is incompatible if used with i2c.h.
While rds-saa6588 isn't installed by defaul
12 matches
Mail list logo
