On Mon, Aug 14, 2017 at 12:37 PM, Florian Fainelli wrote:
>>
>> Please ignore above mib counters. I noticed that I see lot of RxFCSErrors
>> and RxSymbolErrors for extswitch. The count for both counters always
>> remain same.
>
> Yes that is not exactly good, it means that the RGMII interface betw
On 08/13/2017 09:44 PM, Vivek Unune wrote:
> Florian,
>
> On Thu, Jun 29, 2017 at 5:04 PM, Vivek Unune wrote:
>> Florian,
>>
I have managed to use DSA driver and was able detect both internal and
external switches. However, I only get packets flowing only through the
internal swi
Florian,
On Thu, Jun 29, 2017 at 5:04 PM, Vivek Unune wrote:
> Florian,
>
>>> I have managed to use DSA driver and was able detect both internal and
>>> external switches. However, I only get packets flowing only through the
>>> internal switch. I have used the ip & bridge commands to setup the v
Florian,
>> I have managed to use DSA driver and was able detect both internal and
>> external switches. However, I only get packets flowing only through the
>> internal switch. I have used the ip & bridge commands to setup the vlan
>> 101 & 102 for lan and wan respectively.
>>
>> VLAN101 = lan1 l
Hi Vivek,
On 06/27/2017 10:03 AM, Vivek Unune wrote:
> On Wed, Mar 15, 2017 at 5:19 PM, Florian Fainelli
> wrote:
>> On 03/15/2017 01:18 PM, Vivek Unune wrote:
>>> Thanks Florian.
>>>
>>> Let me try this out. First I'll try to figure out how to add a mdio node.
>>>
>>> Over the weekend I was tryi
On Wed, Mar 15, 2017 at 5:19 PM, Florian Fainelli
wrote:
> On 03/15/2017 01:18 PM, Vivek Unune wrote:
>> Thanks Florian.
>>
>> Let me try this out. First I'll try to figure out how to add a mdio node.
>>
>> Over the weekend I was trying enable DSA driver, but did not see DSA
>> under network. I'm
On 03/15/2017 01:18 PM, Vivek Unune wrote:
> Thanks Florian.
>
> Let me try this out. First I'll try to figure out how to add a mdio node.
>
> Over the weekend I was trying enable DSA driver, but did not see DSA
> under network. I'm using LEDE source with kernel 4.9. Nor did I see it
> when I tri
Thanks Florian.
Let me try this out. First I'll try to figure out how to add a mdio node.
Over the weekend I was trying enable DSA driver, but did not see DSA
under network. I'm using LEDE source with kernel 4.9. Nor did I see it
when I tried 'make kernel_menuconfig'
Thanks again.
On Wed, Mar 1
On 03/15/2017 12:34 PM, Vivek Unune wrote:
> Andrew,
>
> I'm not entirely sure. But here is what I observed.
>
> Boot loader sets up both the switches. And I can use all 8 ports of the
> router when I boot Lede. Only the internal swich is detected and
> configurable via swconfig tool
> Internal s
Andrew,
I'm not entirely sure. But here is what I observed.
Bootloader sets up both the switches. And I can use all 8 ports of the
router when I boot Lede. Only the internal switch is detected and
configurable via swconfig tool
Internal switch is connected to CPU via port 5 same as Netgear R8000.
Hi Vivek
> - It has two switches in order to support 8 lan ports. Internal switch is
> BCM53012. The external switch BCM53125 currently works as "dumb switch"
Do you know how the second switch is connected? Is it cascaded off the
internal switch? Or does it have a dedicated Ethernet interface?
Hardware Info
-
Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
DDR3 RAM- 256 MB
Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
Power
12 matches
Mail list logo
