l
for general understanding of life universe and everything.
2012/7/19 Nolan <4030...@gmail.com>:
> -BEGIN PGP SIGNED MESSAGE-
> Hash: SHA1
>
> On 07/19/2012 08:49 AM, Эмиль Кранц wrote:
>> rtfm
>>
>> 2012/7/19 gmspro mailto:gms...@yahoo.com>>
>>
&g
rtfm
2012/7/19 gmspro
> Hi,
>
> In chapter to make the toolchain, binutils and gcc are compiled twice. Why?
> If i don't follow that, or if i don't compiled twice, would there be any
> problem?
>
> Any answer will be highly appreciated?
> Thanks in advance.
>
> --
> http://linuxfromscratch.org/m
post your grub.cfg, for a time only the part concerning the available kernels
Also, state, if you have separate /boot partition
2012/7/14 gmspro
>
> Failure message during booting:
>
> "
> /proc/sys /devmount: Can'f find /dev in /etc/fstab or /etc/mtab
> In: failed to create symbolic link '/d
This is what you have posted:
root:/etc# passwd root
Changing password for root
Enter the new password (minimum of 5 characters)
Please use a combination of upper and lower case letters and numbers.
Bad password: too short.
Warning: weak password (enter it again to use it anyway).
passwd: passwor
you are doing df -h from chroot.
at this stage you cannot read the partition table.
df (and everything else) will work once you logged into lfs as your
primary system.
EK
2012/7/14 gmspro
>
> Hi,
>
> I have a problem running df command.
>
> df -h
> df: cannot read table of mounted file systems
>
the line "passwd: password changed" says otherwise
you have changed your password.
there will be no visible indications of changing password.
try to log in
2012/7/14 gmspro
> Hi,
>
> I completed chapter 6.
> During installation of chapter 6 i didn't set root password.
> After completing and doi
b and mplayer were built with -j2, no problem
EK
On 16 May 2012 13:29, Simon Geard wrote:
> On Tue, 2012-05-15 at 19:43 +0300, Эмиль Кранц wrote:
> > By trial and error I have found that any action that takes more than
> > one SBU in LFS is better off with -j1.
> >
By trial and error I have found that any action that takes more than one
SBU in LFS is better off with -j1.
BLFS packages are more agreeable with -j2 switch.
On my dual core machine only kernel compiles flawlessly with -j2 switch.
Binutils and compiled against them gcc and glibc were all faulty w
oot/grub/grub.cfg
depending on your hard drive type.
EK
On 14 May 2012 16:20, Lázaro Morales wrote:
> En 14/05/2012 08:54:50, Эмиль Кранц escribió:
>
> > Have a closer look: /dev/sdaX in fstab and /dev/hdaX in error message
> > IDE and SCSI? Typo?
> > Cheerio.
>
Have a closer look: /dev/sdaX in fstab and /dev/hdaX in error message
IDE and SCSI? Typo?
Cheerio.
On 14 May 2012 15:37, Lázaro Morales wrote:
> En 11/05/2012 15:58:14, Bruce Dubbs escribió:
>
> > Lázaro Morales wrote:
> >> Hello,
> >>
> >> After complete the LFS book, when I restart the compu
On 9 April 2012 17:11, Sean Hinchee wrote:
> This is my first time going through LFS, everything went fine (I think)
> up until I tried "sudo make" on glibc. I followed the directions
> verbatim and I have run through the steps from "gcc-4.6.2 - Pass 1" all
> the way back up to glibc. Everytime I
igure script allows to continue.
Again, if trying to replicate the condition after the full
installation - only harmless warning will be issued.
Emile Krantz
On 8 April 2012 21:10, Эмиль Кранц wrote:
> Тhere is a difference between warning and error.
> Configure script for ncurses in c
k there is a need to go to lfs-dev since it is just a
matter of adding a switch to configure script, nothing fancy.
Emile Krantz
On 7 April 2012 21:49, Eleanore Boyd wrote:
> On 4/7/2012 12:11 PM, Эмиль Кранц wrote:
>> Hello all.
>> Ncurses configure script during the Temp
Hello all.
Ncurses configure script during the Temp tools stage (chapter 5.15)
gives an error, requesting to be complied against gpm. As gpm is
installed in BLFS, the key "--without-gpm" should be passed to the
configure script, in addition. All works well from there.
Cheers.
Emile Krantz
--
http:
14 matches
Mail list logo
