From: Ben Greear
Among other things, this will check for an htt-mgt variant of
ath10k-ct firmware before loading 'normal' firmware, and it disables
verbose printing of firmware DBGLOG messages by default.
Signed-off-by: Ben Greear
---
package/kernel/ath10k-ct/Makefile | 4 ++--
1 file changed,
From: Ben Greear
The HTT-MGT variants transport management frames over the
normal HTT tx path, just like data frames. This saves
limitted WMI buffers which can become depleted if lots of
management frames become stuck in TX queues due to peer
that went away.
In addition, at least for the wave-1
From: Ben Greear
This updates to latest ath10k-ct firmware. Hopefully we are
at the end of the development cycle for this firmware release,
so these should be stable.
wave-1 changes since last release:
Release 20
* Allow flushing peer when deleting. Hopefully this will allow the
peer
From: Ben Greear
Update DEPENDS and PROVIDES so that ath10k-ct firmware
and drivers can be used to replace stock firmware
and drivers. The -htt firmware variant, which requires
ath10k-ct driver now selects ath10k-ct driver when the
firmware is selected.
Signed-off-by: Ben Greear
---
NOTE: Th
New WRT3200ACM routers are unflashable due to a changed flash chip that is
unsupported.
There is a fix proposal from Kaloz, authored on 15th of February, in his
staging repo, but that is still uncommitted to the main sources for some
reason. Announcing the fix:
https://forum.openwrt.org/vie
20.03.2018 09:54, Kyson Lok:
Override the LAN MAC to use the same address as WAN.
The stock firmware uses the same MAC address for all
interfaces.
Signed-off-by: Kyson Lok
---
target/linux/ramips/base-files/etc/board.d/02_network | 1 +
1 file changed, 1 insertion(+)
diff --git a/target/lin
20.03.2018 10:22, Koen Vandeputte:
On 2018-03-20 09:54, Kyson Lok wrote:
Override the LAN MAC to use the same address as WAN.
The stock firmware uses the same MAC address for all
interfaces.
Besides blindly following the stock firmware behavior,
is there *any* advantage in doing this?
The g
Here is our customer's issue.
> Flash Openwrt snapshot from
> https://downloads.openwrt.org/snapshots/targets/ramips/mt76x8/openwrt-ramips-mt76x8-gl-mt300n-v2-squashfs-sysupgrade.bin
>
> Install luci, luci-sqm-app packages
>
> Configure SQM QoS by setting interface name to eth0.2 and entering dow
On 2018-03-20 09:54, Kyson Lok wrote:
Override the LAN MAC to use the same address as WAN.
The stock firmware uses the same MAC address for all
interfaces.
Besides blindly following the stock firmware behavior,
is there *any* advantage in doing this?
Signed-off-by: Kyson Lok
---
target/li
Bjørn Mork wrote:
Felix Fietkau writes:
On 2018-03-19 10:51, Bjørn Mork wrote:
A regression seriously affecting the Linksys WRT1900ACv1 (Mamba) was
introduced some time between the OpenWrti/LEDE v4.4 and v4.9 kernels.
The root cause has not yet been identified, despite many attempts f
Override the LAN MAC to use the same address as WAN.
The stock firmware uses the same MAC address for all
interfaces.
Signed-off-by: Kyson Lok
---
target/linux/ramips/base-files/etc/board.d/02_network | 1 +
1 file changed, 1 insertion(+)
diff --git a/target/linux/ramips/base-files/etc/board.d/
11 matches
Mail list logo
