KR> aileron bell crank

The subject recently came up of the aileron bell crank not fitting within the structure of the new wing. I came across a photo showing why I suggested the bell crank assembly could be compressed and still not cause interference of the cable crossover. Check it out. http://myplace.frontie

KR> aileron Bell crank AS5048 airfoil

I apologize, I did leave a lot of the question out. My specific question should have been" With the pulley that you see in the video, do you believe that the bell crank will have enough travel to effectively move the aileron to full recommended deflection? Yes the other cable will be as recommen

KR> aileron Bell crank AS5048 airfoil

I was able to keep the everything the same on my installation except I swapped the pulleys. This allowed me to have the cable higher since the rear spar is raised up on the New airfoil. You can see how I did it at mykitlog.com/vr6chris. Chris Pryce Burlington, NJ

KR> aileron Bell crank AS5048 airfoil

At 11:12 AM 2/18/2016, you wrote: >Please check this video and tell me if you think it will work. +++ Can't really tell without seeing how you intend to close the "loop" on the system. What is the system from the stick to the bellcrank? Also, the

KR> aileron Bell crank AS5048 airfoil

Yes on the sarcasm. Lol. I prefer aluminum tube to side of bell crank next to spar. Or "pull-pull" cable. You will probably get several better ideas before long. I don't see how it would work as shown on video. Good luck. On Feb 18, 2016 12:54 PM, "Adam via KRnet" wrote: > Via Cable? Yes, or was

KR> aileron Bell crank AS5048 airfoil

Via Cable? Yes, or was I supposed to read the sarcasm in that statement? Adam Tippin A&P KR2S builder > On Feb 18, 2016, at 1:17 PM, Mike Arnold via KRnet > wrote: > > Adam can you reach the bell crank from the cockpit??? >

KR> aileron Bell crank AS5048 airfoil

Adam can you reach the bell crank from the cockpit??? On Feb 18, 2016 11:14 AM, "Adam Tippin via KRnet" wrote: > Please check this video and tell me if you think it will work. If not > think of some recommendations to make it work please and thank you.Youtube > Link

KR> aileron Bell crank AS5048 airfoil

Please check this video and tell me if you think it will work. If not think of some recommendations to make it work please and thank you.Youtube Link

KR> Aileron bell crank - Aluminum extruded tube

Netters, I am trying to help a French builder who needs an aluminium tube to make the aileron bell crank. The drawing calls for .125 wall, 1" x 2". We wanted to ordr it from Aircraft Spruce, but if I am not mistaken, they stock only square tubing. Any suggestions? Serge Vidal KR2 ZS-WEC Paris

KR> Aileron bell crank - Aluminum extruded tube

Serge Try www.mcmaster.com They have what you want in 6063 Al. Carroll Seibert Serge VIDAL wrote: >Netters, > >I am trying to help a French builder who needs an aluminium tube to make >the aileron bell crank. The drawing calls for .125 wall, 1" x 2". We >wanted to ordr it from Aircraft Spruce,

KR> Aileron bell crank - Aluminum extruded tube

Carroll Seibert wrote: > Try www.mcmaster.com They have what you want in 6063 Al. But 6063 is only a little better than half as strong as 6061. If your plans call for 6061, you either better stick to it or make it thicker (and heavier). Wicks Aircraft at www.wicksaircraft.com sells 1x2x.125 60

KR> Aileron bell crank - Aluminum extruded tube

see http://www.wicksaircraft.com/catalog/product_cat.php/subid=1856/index.html for source Mark Langford, Huntsville, Alabama see KR2S project N56ML at http://home.hiwaay.net/~langford email to N56ML "at" hiwaay.net --

Réf. : Re: KR> Aileron bell crank - Aluminum extruded tube

illez répondre à KRnet Remis le : 2005-01-15 17:04 Pour : KRnet cc :(ccc : Serge VIDAL/DNSA/SAGEM) Objet : Re: KR> Aileron bell crank - Aluminum extruded tube Serge Try www.mcmaster.com They have what you want in 6063 Al. Carroll Seibert Serge VIDAL wrote: >Nette

KR> Aileron bell crank - Aluminum extruded tube

Mt. Vernon - 2005 - KR Gathering ---Original Message--- From: KRnet List-Post: krnet@list.krnet.org Date: 01/15/05 10:54:32 To: kr...@mylist.net Subject: KR> Aileron bell crank - Aluminum extruded tube Netters, I am trying to help a French builder who needs an aluminium tube to make

KR> Aileron bell crank assembly

My aileron bell cranks have been built with a sort of large aluminum spacer between the bell crank brackets and the WAFs. I suspect these brackets are redundant, because I can find no trace of them in the drawings; but I would like to make sure. Does anybody have some info about that? Serge Vi