On Wed, 19 Jan 2022 02:08:38 +0530, Rajeev Nandan wrote:
> In most cases, the default values of DSI PHY tuning registers should be
> sufficient as they are fully optimized. However, in some cases where
> extreme board parasitics cause the eye shape to degrade, the override
> bits can be used to imp
On 11/25/2021 6:35 PM, Dmitry Baryshkov wrote:
DPU driver contains code to parse clock items from device tree into
special data struct and then enable/disable/set rate for the clocks
using that data struct. However the DPU driver itself uses only parsing
and enabling/disabling part (the rate sett
one>
On 2021-08-17 20:30, abhin...@codeaurora.org wrote:
On 2021-06-17 15:20, Dmitry Baryshkov wrote:
DPU interrupts code allows multiple callbacks per interrut. In reality
/interrupt
none of the interrupts is shared between blocks (and will probably
never
be). Drop support for registering m
Quoting Kuogee Hsieh (2022-01-18 10:47:25)
> Current DP drivers have regulators, clocks, irq and phy are grouped
> together within a function and executed not in a symmetric manner.
> This increase difficulty of code maintenance and limited code scalability.
> This patch divides the driver life cyc
On 1/18/2022 12:01 PM, Dmitry Baryshkov wrote:
On Tue, 18 Jan 2022 at 22:41, Abhinav Kumar wrote:
On 12/7/2021 2:29 PM, Dmitry Baryshkov wrote:
Currently the DSI driver has two separate paths: one if the next device
in a chain is a bridge and another one if the panel is connected
directl
Add support for MSM DSI PHY tuning configuration. Current design is
to support drive strength and drive level/amplitude tuning for
10nm PHY version, but this can be extended to other PHY versions.
Signed-off-by: Rajeev Nandan
---
Changes in v2:
- New.
- Split into generic code and 10nm-specifi
The clock and data lanes of the DSI PHY have a calibration circuitry
feature. As per the MSM DSI PHY tuning guidelines, the drive strength
tuning can be done by adjusting rescode offset for hstop/hsbot, and
the drive level tuning can be done by adjusting the LDO output level
for the HSTX drive.
Si
In most cases, the default values of DSI PHY tuning registers should be
sufficient as they are fully optimized. However, in some cases where
extreme board parasitics cause the eye shape to degrade, the override
bits can be used to improve the signal quality.
The general guidelines for DSI PHY tuni
This series is to add DSI PHY tuning support in Qualcomm Snapdragon
SoCs with 10nm DSI PHY e.g. SC7180
In most cases the default values of DSI PHY tuning registers
should be sufficient as they are fully optimized. However, in
some cases (for example, where extreme board parasitics cause
the eye sh
On Tue, 18 Jan 2022 at 22:29, Abhinav Kumar wrote:
>
>
>
> On 12/7/2021 2:29 PM, Dmitry Baryshkov wrote:
> > The DSI subsystem does not fully fall into the pre-enable/enable system
> > of callbacks, since typically DSI device bridge drivers expect to be
> > able to communicate with DSI devices at
On Tue, 18 Jan 2022 at 22:41, Abhinav Kumar wrote:
>
>
>
> On 12/7/2021 2:29 PM, Dmitry Baryshkov wrote:
> > Currently the DSI driver has two separate paths: one if the next device
> > in a chain is a bridge and another one if the panel is connected
> > directly to the DSI host. Simplify the code
On 1/5/2022 11:06 PM, Dmitry Baryshkov wrote:
The round_pixclk() callback returns different rate only on MDP4 in HDMI
(DTV) case. Stop using this callback in other cases to simplify
mode_valid callbacks.
Signed-off-by: Dmitry Baryshkov
Reviewed-by: Abhinav Kumar
---
Changes since v1:
-
On 12/7/2021 2:29 PM, Dmitry Baryshkov wrote:
Currently the DSI driver has two separate paths: one if the next device
in a chain is a bridge and another one if the panel is connected
directly to the DSI host. Simplify the code path by using panel-bridge
driver (already selected in Kconfig) and
On 12/7/2021 2:29 PM, Dmitry Baryshkov wrote:
The DSI subsystem does not fully fall into the pre-enable/enable system
of callbacks, since typically DSI device bridge drivers expect to be
able to communicate with DSI devices at the pre-enable() callback. The
reason is that for some DSI hosts en
Each DP link training contains link training 1 followed by link
training 2. There is maximum of 5 retries of DP link training
before declared link training failed. It is required to stop link
training at end of link training 2 if it is failed so that next
link training 1 can start freshly. This pa
From: Kuogee Hsieh
Some DP sinkers prefer to use tps4 instead of tps3 during training #2.
This patch will use tps4 to perform link training #2 if sinker's DPCD
supports it.
Changes in V2:
-- replace dp_catalog_ctrl_set_pattern() with
dp_catalog_ctrl_set_pattern_state_bit()
Changes in V3:
--
DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose
and expect DP source return correct checksum. During drm edid read,
correct edid checksum is calculated and stored at
connector::real_edid_checksum.
The problem is struct dp_panel::connector never be assigned, instead the
connect
Current DP drivers have regulators, clocks, irq and phy are grouped
together within a function and executed not in a symmetric manner.
This increase difficulty of code maintenance and limited code scalability.
This patch divides the driver life cycle of operation into four states,
resume (including
Group below 4 dp driver related patches into one series.
Kuogee Hsieh (4):
drm/msm/dp: do not initialize phy until plugin interrupt received
drm/msm/dp: populate connector of struct dp_panel
drm/msm/dp: add support of tps4 (training pattern 4) for HBR3
drm/msm/dp: stop link training after
19 matches
Mail list logo
