et 0 lun 0
da0: Fixed Direct Access SCSI-2 device
da0: 3.300MB/s transfers
da0: Command Queueing Enabled
da0: 34816MB (71303168 512 byte sectors: 255H 63S/T 4438C)
Any suggestions?
Thanks,
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre
onsole) becomes very unresponsive when I/O
is writing at maximum bandwidth.
Anyway, system becomes more responsive when using ULE scheduler instead
of 4BSD during I/O.
Is there a way to limit the maximum I/O bandwidth used by the controller?
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticell
camcontrol?
`camcontrol negotiate 0:0 -W 16' might improve that transfer settings.
camcontrol needs passthrough device support in a kernel.
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information abou
0:0 -W 16 -O 127 -R 40.000'.
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our website at http://www.Skyt
40.000'.
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our website at http://www.Skytek.it
---
___
freebsd-s
frame to the correct interface. Therefore, if the frame destination is
the mac address of the bridge,
it will not forward it, since it simply already arrived at destination.
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For
: no carrier even on lagg0 interface, while bce0 shows no
carrier (correct) and
bce1 is active.
Any ideas?
Thanks!
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit
d SAN hardware in FreeBSD?
I'm especially interested in support for HP EVA/XP disk arrays, Qlogic
HBAs, multipathing.
How FreeBSD compares in this environment to RHEL 5?
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further i
ault
cpuid = 0
It just stays there, unresponsive (no automatic reboot).
Any ideas?
Thanks,
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our websi
ideas of why i wasn't able to collect dump and the
system did not
reboot automatically?
Thanks,
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our website at
Hello,
disabling acpi is not an option, since i'm running SMP.
I have several other systems running 7.0 Release without problems,
so it might be something on 7-Stable.
Thanks,
Daniel
Jeremy Chadwick ha scritto:
On Sat, Jun 07, 2008 at 11:34:41PM +0200, Daniel Ponticello wrote:
Sorry, I did not read well you suggestion ;)
Anyway, the system reboots correctly if I issue the reboot command from
command line.
Should i adjust those values anyway?
Thanks,
Daniel
Daniel Ponticello ha scritto:
Hello,
disabling acpi is not an option, since i'm running SMP.
I
have more informations to open a PR.
Thanks,
Daniel
Jeremy Chadwick ha scritto:
On Sun, Jun 08, 2008 at 03:07:08PM +0200, Daniel Ponticello wrote:
Sorry, I did not read well you suggestion ;)
Anyway, the system reboots correctly if I issue the reboot command from
command line.
Should i
scritto:
Daniel Ponticello wrote:
On FreeBSD7, i'm succesfully using Qlogic 4gb fibre channel HBAs (ISP
driver)
attached to Fibre Brocade Switch and IBM DS4700 (14 disks array)
using 4 way multipath
with gmultipath.
So far the support in gmultipath is active/passive only? I think in
RH5 yo
14 matches
Mail list logo
