scritto:
Daniel Ponticello wrote:
On FreeBSD7, i'm succesfully using Qlogic 4gb fibre channel HBAs (ISP
driver)
attached to Fibre Brocade Switch and IBM DS4700 (14 disks array)
using 4 way multipath
with gmultipath.
So far the support in gmultipath is active/passive only? I think in
RH5 yo
have more informations to open a PR.
Thanks,
Daniel
Jeremy Chadwick ha scritto:
On Sun, Jun 08, 2008 at 03:07:08PM +0200, Daniel Ponticello wrote:
Sorry, I did not read well you suggestion ;)
Anyway, the system reboots correctly if I issue the reboot command from
command line.
Should i
Sorry, I did not read well you suggestion ;)
Anyway, the system reboots correctly if I issue the reboot command from
command line.
Should i adjust those values anyway?
Thanks,
Daniel
Daniel Ponticello ha scritto:
Hello,
disabling acpi is not an option, since i'm running SMP.
I
Hello,
disabling acpi is not an option, since i'm running SMP.
I have several other systems running 7.0 Release without problems,
so it might be something on 7-Stable.
Thanks,
Daniel
Jeremy Chadwick ha scritto:
On Sat, Jun 07, 2008 at 11:34:41PM +0200, Daniel Ponticello wrote:
ideas of why i wasn't able to collect dump and the
system did not
reboot automatically?
Thanks,
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our website at
ault
cpuid = 0
It just stays there, unresponsive (no automatic reboot).
Any ideas?
Thanks,
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our websi
d SAN hardware in FreeBSD?
I'm especially interested in support for HP EVA/XP disk arrays, Qlogic
HBAs, multipathing.
How FreeBSD compares in this environment to RHEL 5?
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further i
: no carrier even on lagg0 interface, while bce0 shows no
carrier (correct) and
bce1 is active.
Any ideas?
Thanks!
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit
frame to the correct interface. Therefore, if the frame destination is
the mac address of the bridge,
it will not forward it, since it simply already arrived at destination.
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For
0:0 -W 16 -O 127 -R 40.000'.
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our website at http://www.Skyt
40.000'.
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information about our services:
- Please visit our website at http://www.Skytek.it
---
___
freebsd-s
camcontrol?
`camcontrol negotiate 0:0 -W 16' might improve that transfer settings.
camcontrol needs passthrough device support in a kernel.
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre of Skytek
---
- For further information abou
onsole) becomes very unresponsive when I/O
is writing at maximum bandwidth.
Anyway, system becomes more responsive when using ULE scheduler instead
of 4BSD during I/O.
Is there a way to limit the maximum I/O bandwidth used by the controller?
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticell
et 0 lun 0
da0: Fixed Direct Access SCSI-2 device
da0: 3.300MB/s transfers
da0: Command Queueing Enabled
da0: 34816MB (71303168 512 byte sectors: 255H 63S/T 4438C)
Any suggestions?
Thanks,
Daniel
--
WBR,
Cordiali Saluti,
Daniel Ponticello, VP of Engineering
Network Coordination Centre
14 matches
Mail list logo
