HEADS UP!!!
The rr232x driver has been removed at the request of Highpoint. The
reason is that is has been superseded by the hptrr driver and is no
longer supported by Highpoint. If you use this driver, you must
update your kernel config and/or module loading config to point to the
hptrr driver
On Sun, Feb 03, 2008 at 03:04:52AM +0300, Dmitry Morozovsky wrote:
> Dear colleagues,
>
> during rsycn from eSATA drive connected to Promise TX4 (ad12) to ZFS pool
> eSATA disk got disconnected. With the next access, system crashed:
>
> Unread portion of the kernel message buffer:
>
>
> Fatal
DAPATKAN PINJAMAN TANPA AGUNAN DENGAN PERSYARATAN YANG MUDAH,PROSES
YANG CEPAT,
DAN FASILTAS BERUPA BEBAS PROVISI/ADM 3% UNTUK PINJAMAN 15.000.000 -
19.000.000
DENGAN TENOR/MASA PELUNASAN 24 BULAN DAN PINJAMAN >=20.000.000,-
DENGAN TENOR
36 BULAN. PROSES VERIFIKASI HINGGA PENCAIRAN 5-7 HARI KERJ
DAPATKAN PINJAMAN TANPA AGUNAN DENGAN PERSYARATAN YANG MUDAH,PROSES
YANG CEPAT,
DAN FASILTAS BERUPA BEBAS PROVISI/ADM 3% UNTUK PINJAMAN 15.000.000 -
19.000.000
DENGAN TENOR/MASA PELUNASAN 24 BULAN DAN PINJAMAN >=20.000.000,-
DENGAN TENOR
36 BULAN. PROSES VERIFIKASI HINGGA PENCAIRAN 5-7 HARI KERJ
Hi, the subject tells it all, I cannot start x11 with intel drivers
FreeBSD 7.0-RC1 (nothing changed, just installed from CD)
then I just added x11 by pkg_add -r xorg removed video-i810 driver
package and added video-intel driver also by pkg_add -r ...
all other configuration is below, along wit
On Fri, 2008-02-01 at 15:26 +0100, Danny Pansters wrote:
> On Thursday 31 January 2008 16:05:57 Andriy Gapon wrote:
> > on 31/01/2008 14:39 Andriy Gapon said the following:
> > > on 31/01/2008 13:07 John Baldwin said the following:
> > >> On Wednesday 30 January 2008 12:39:14 pm Andriy Gapon wrote
Dear colleagues,
during rsycn from eSATA drive connected to Promise TX4 (ad12) to ZFS pool
eSATA disk got disconnected. With the next access, system crashed:
Unread portion of the kernel message buffer:
Fatal trap 12: page fault while in kernel mode
cpuid = 1; apic id = 01
fault virtual addres
Hi all!.
Today i brought a usb wifi dongle (Linksys WUSB54GC) and test it with
yesterdays releng_7 with a plain generic kernel.
It is configured with wpa_supplicant [0].
When i generate some traffic on it, i get panics [1].
Does anyboady else has problems with it?
How can i go further and coll
On Sat, Feb 02, 2008 at 07:42:46PM +, Matthew Herzog wrote:
> What is the proper way to turn on the checksum offloading for an Intel
> fxp card?
>
> Yes, it's obvious I can do it by hand with ifconfig. That works fine.
> How do enable it in rc.conf so that
> it happens upon each reboot? I sear
What is the proper way to turn on the checksum offloading for an Intel
fxp card?
Yes, it's obvious I can do it by hand with ifconfig. That works fine.
How do enable it in rc.conf so that
it happens upon each reboot? I searched the www for an hour and found no
examples.
My guess would be -flags li
Dominic Fandrey wrote:
> The sources were csupped ~3 hours ago. My CC is defined as follows:
> env CCACHE_PREFIX=/usr/local/bin/distcc /usr/local/bin/ccache cc
>
> I have done many buildworld, buildkernel and port builds with this setting and
> it never caused any problems. However today buildworl
Gerrit Kühn wrote:
> Hi folks,
>
> I have just noticed that the NO-knobs were renamed into WITHOUT-knobs and
> moved from make.conf into src.conf.
> Can anyone tell me if (and how) this interacts with nanobsd, which uses
> the following variables:
>
> ---
> # Options to put in make.conf during bu
The sources were csupped ~3 hours ago. My CC is defined as follows:
env CCACHE_PREFIX=/usr/local/bin/distcc /usr/local/bin/ccache cc
I have done many buildworld, buildkernel and port builds with this setting and
it never caused any problems. However today buildworld fails the following way:
env C
13 matches
Mail list logo
