On Fri, 24 Jul 2009 16:34:35 +0200
"Leslie Jensen" wrote:
>
> I've followed every advice in /usr/ports/UPDATING
>
> The portmaster -r jpeg* returns "No match".
>
> portmaster -r jpeg-7 rebuilds only jpeg-7 no other ports!
>
> After this upgrad
I've followed every advice in /usr/ports/UPDATING
The portmaster -r jpeg* returns "No match".
portmaster -r jpeg-7 rebuilds only jpeg-7 no other ports!
After this upgrade my X won't start :-(
Any hints?
Thanks
Leslie
-- snip ---
(II) LoadMod
/Leslie
of course turn off hald, and run moused.
Unfortunately that did not fix the problem :-(
What do I test next?
/Leslie
do
X -configure
and look at xorg.conf then try fixing something there.
___
freebsd-questions@freebsd.org mailing list
h
Glen Barber skrev:
Leslie,
On Fri, May 29, 2009 at 3:06 PM, Leslie Jensen wrote:
of course turn off hald, and run moused.
Unfortunately that did not fix the problem :-(
What do I test next?
Could you paste the output of:
cd /usr/ports/x11/xorg; make missing
There's no output!
This
Leslie,
On Fri, May 29, 2009 at 3:06 PM, Leslie Jensen wrote:
>> of course turn off hald, and run moused.
>>
> Unfortunately that did not fix the problem :-(
> What do I test next?
Could you paste the output of:
cd /usr/ports/x11/xorg; make missing
--
Glen Barber
_
Wojciech Puchar skrev:
Produces the same result :-(
wouldn't it be better to pkg_delete xserver, make config, turn off
hal dependency and then install. Probably it will work fine then.
Sounds lika a good idea. I'll try it and repport back.
/Leslie
of course turn off hald, and run mouse
Produces the same result :-(
wouldn't it be better to pkg_delete xserver, make config, turn off hal
dependency and then install. Probably it will work fine then.
Sounds lika a good idea. I'll try it and repport back.
/Leslie
of course turn off hald, and run moused.
___
Wojciech Puchar skrev:
Errors from xkbcomp are not fatal to the X server
(EE) config/hal: NewInputDeviceRequest failed
(EE) config/hal: NewInputDeviceRequest failed
Protocol not supported by server
Do you have
dbus_enable="YES"
hald_enable="YES"
in your /etc/rc.conf ?
Yes I have
If
Errors from xkbcomp are not fatal to the X server
(EE) config/hal: NewInputDeviceRequest failed
(EE) config/hal: NewInputDeviceRequest failed
Protocol not supported by server
Do you have
dbus_enable="YES"
hald_enable="YES"
in your /etc/rc.conf ?
Yes I have
If not: add them, reboot and
Peter Ulrich Kruppa skrev:
On Fri, 29 May 2009, Leslie Jensen wrote:
When I try to startx my screen goes black for a while and then it
returns to the prompt.
At the screen I see this
The XKEYBOARD keymap compiler (xkbcomp) reports:
Warning: Type "ONE_LEVEL" has 1 levels, but ha
On Fri, 29 May 2009, Leslie Jensen wrote:
When I try to startx my screen goes black for a while and then it returns to
the prompt.
At the screen I see this
The XKEYBOARD keymap compiler (xkbcomp) reports:
Warning: Type "ONE_LEVEL" has 1 levels, but has 2 symbols
When I try to startx my screen goes black for a while and then it
returns to the prompt.
At the screen I see this
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning: Type "ONE_LEVEL" has 1 levels, but has 2 symbols
> Ignoring extra symbols
Errors from xkbco
On Saturday 02 August 2008 02:30:22 David Gurvich wrote:
> Have you loaded all the kernel modules you need and installed
> xf86-video-chips?
I am not aware of any kernel modules that i would have to load explicitely.
And, yes, as indicated by the Xorg.log snippet, the chips driver is present.
___
Have you loaded all the kernel modules you need and installed
xf86-video-chips?
___
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
Hello List,
I got an old TFT that uses a special connector to a CHIPS ct65554 graphics
card. However, although the ct65554 is listed as supported, it is not
recognized by the chips driver. System is FreeBSD 7-Release AMD64. I am
pretty sure that the same xorg.conf worked under i386.
pciconf -
[EMAIL PROTECTED] wrote:
I just upgraded from 5.3 to 5.4 RC3 via sysinstall from a cd.The
upgrade was successful however, when I try "startx" I get the
following error:
(EE) Failed to load module "speedo" (module does not exit,0)
(EE) Failed to load module "Keyboard" (module does not exit,0)
(EE) N
On 5/1/2005 19:49, [EMAIL PROTECTED] wrote:
I just upgraded from 5.3 to 5.4 RC3 via sysinstall from a cd.The
upgrade was successful however, when I try "startx" I get the
following error:
(EE) Failed to load module "speedo" (module does not exit,0)
(EE) Failed to load module "Keyboard" (module does
On Sun, May 01, 2005 at 10:19:17AM -0400, [EMAIL PROTECTED] wrote:
> (EE) Failed to load module "speedo" (module does not exit,0)
> (EE) Failed to load module "Keyboard" (module does not exit,0)
> (EE) No input driver matching 'Keyboard'
> No core keyboard
>
> Fatal server error:
> failed to initi
I just upgraded from 5.3 to 5.4 RC3 via sysinstall from a cd.The
upgrade was successful however, when I try "startx" I get the
following error:
(EE) Failed to load module "speedo" (module does not exit,0)
(EE) Failed to load module "Keyboard" (module does not exit,0)
(EE) No input driver matching
On Tuesday, 5 August 2003 at 14:21:38 +0200, mess-mate wrote:
> Hi,
> X no more start after a crash with root.
> Error Knotify, kdeinit, etc.. pid...
If you get that far, X is running. Those error messages are there for
a purpose. Read them.
> As user all goes well.
So you're saying that root
Hi,
X no more start after a crash with root.
Error Knotify, kdeinit, etc.. pid...
As user all goes well.
What can I do ??
Thanks for your help.
mess-mate
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To un
21 matches
Mail list logo
