-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/25/07 9:08 PM, Ted Mittelstaedt wrote:
> There are two physical disks in the server. bus 1 target 0 and
> bus 1 target 1. Those ARE the physical disks. If one of them
> has failed instead of:
>
> Sync, Ultra2, Wide - Configured in a logical
ssage-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Behalf Of David Newman
> Sent: Sunday, November 25, 2007 2:58 PM
> To: Ted Mittelstaedt
> Cc: freebsd-questions@freebsd.org
> Subject: Re: dealing with a failing drive
>
>
> -BEGIN PGP SIGNED MESSAGE-
On Sun, 25 Nov 2007 08:45:46 +
Matthew Seaman <[EMAIL PROTECTED]> wrote:
> sysutils/aaccli aaccli-1.0 Adaptec SCSI RAID administration
>
As I said in my previous post, this is EXACTLY what was wanted.
Installation of aaccli was a snap. My only problem was the total lack
of documen
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/24/07 12:39 PM, Ted Mittelstaedt wrote:
> The output of idacontrol show will show if one of the
> hard disks in the SmartArray has failed. Your choice with
> a hardware array is to either run it with redundancy or not.
> (ie: raid5 or mirroring
On Sun, 25 Nov 2007 08:45:46 +
Matthew Seaman <[EMAIL PROTECTED]> wrote:
>... it's a rebadged Adaptec RAID controller using
> the aac
Wonderful; I can now look into and play with the RAID system without
taking the OS off-line and going to the bios.
Thanks!
Bob
--
_
/o\
// \\ The ASC
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA256
Bob Richards wrote:
> I have a similar issue, only it is with a Dell server which has 6 SCSI
> drives in a hardware raid array. The controller is a Dell PERC 2/Si.
>
> Is there an equivalent monitor utility for this as well? I am currently
> runnin
> Compaq uses several RAID cards most are under the so-called
> "SmartArray" using the ida driver. If this is yours, you can
> use a utility called "idacontrol" that can monitor the array,
Interesting discussion!
I have a similar issue, only it is with a Dell server which has 6 SCSI
drives in a
Of David Newman
> Sent: Monday, November 19, 2007 8:44 AM
> To: freebsd-questions@freebsd.org
> Subject: Re: dealing with a failing drive
>
>
> -BEGIN PGP SIGNED MESSAGE-
> Hash: SHA1
>
> On 11/18/07 11:30 PM, Ted Mittelstaedt wrote:
> > Hi David, apologie
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/18/07 11:30 PM, Ted Mittelstaedt wrote:
> idacontrol show | grep "Status"
>
> IF status is fully up it will say:
>
> Status: Logical drive ok
And that's what it does say. So far so good...
...but then each time I run idacontrol I get this in
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/18/07 11:30 PM, Ted Mittelstaedt wrote:
> Hi David, apologies to Jerry for jumping in.
>
> Compaq uses several RAID cards most are under the so-called
> "SmartArray" using the ida driver. If this is yours, you can
> use a utility called "idaco
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Behalf Of Jerry
> McAllister
> Sent: Monday, November 12, 2007 8:04 AM
> To: David Newman
> Cc: freebsd-questions@freebsd.org
> Subject: Re: dealing with a failing drive
>
>
> O
From: "Jerry McAllister" <[EMAIL PROTECTED]>
Sent: Monday, November 12, 2007 12:53
On Mon, Nov 12, 2007 at 09:26:38AM -0800, David Newman wrote:
On 11/12/07 8:14 AM, Jerry McAllister wrote:
> An update: After doing what you suggest (leaving in the "good" disk,
> adding a new disk, RAID rebui
From: "David Newman" <[EMAIL PROTECTED]>
-BEGIN PGP SIGNED MESSAGE-
On 11/12/07 8:14 AM, Jerry McAllister wrote:
An update: After doing what you suggest (leaving in the "good" disk,
adding a new disk, RAID rebuilding) I still got soft write errors --
with *either one* of the disks I
On Mon, Nov 12, 2007 at 09:26:38AM -0800, David Newman wrote:
> -BEGIN PGP SIGNED MESSAGE-
> Hash: SHA1
>
> On 11/12/07 8:14 AM, Jerry McAllister wrote:
>
> > An update: After doing what you suggest (leaving in the "good" disk,
> > adding a new disk, RAID rebuilding) I still got soft wri
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/12/07 8:14 AM, Jerry McAllister wrote:
> An update: After doing what you suggest (leaving in the "good" disk,
> adding a new disk, RAID rebuilding) I still got soft write errors --
> with *either one* of the disks I tried.
>
> Then I tried putt
On Sun, Nov 11, 2007 at 07:56:52AM -0800, David Newman wrote:
> -BEGIN PGP SIGNED MESSAGE-
> Hash: SHA1
>
> On 11/10/07 9:09 PM, Modulok wrote:
> >>> I'd welcome suggestions on how (or whether) to try to revive a SCSI
> > drive that's failing.
> >
> > It depends on how valuable the data
On Sat, Nov 10, 2007 at 05:22:06PM -0800, David Newman wrote:
> -BEGIN PGP SIGNED MESSAGE-
> Hash: SHA1
>
> I'd welcome suggestions on how (or whether) to try to revive a SCSI
> drive that's failing.
to answer 'whether': don't. Get your stuff off from it as
soon as possible and nuke i
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 11/10/07 9:09 PM, Modulok wrote:
>>> I'd welcome suggestions on how (or whether) to try to revive a SCSI
> drive that's failing.
>
> It depends on how valuable the data on the array is, and more
> importantly, how much funding you have at your disp
>> I'd welcome suggestions on how (or whether) to try to revive a SCSI
drive that's failing.
It depends on how valuable the data on the array is, and more
importantly, how much funding you have at your disposal to fix the
problem. If it were me, I would set aside the bad disk, connect a new
disk t
19 matches
Mail list logo
