Jim Pirzyk wrote:
>
> So I tried to use the one2many netgraph module, but I get errors
> right away. Here is what I get:
>
> Jim.Pirzyk@snoopy:~
> 47>sudo ngctl -d mkpeer trnk0: one2many upper one
> ngctl: sendto(trnk0:): No such file or directory
> ngctl: send msg: No such file or directory
>
Sjaak Jobses wrote:
>
> Stacey Roberts wrote:
> >
> > Hi Guys,
> >I've just ordered FreeBSD V4.3, hoping to install it on a VP6 Dual proc
> > system running two P111 933's.
> >
> > I've tried searching for known issues with this particular motherboard via
> > all the search facilities at the
>> we had a local discussion within KAME. we do not really like to
>> support PF_LOCAL, unless there's clear standard behavior for AF_LOCAL
>> case.
>I think this is the wrong approach. If we're always going to wait for
>a clear and standarized behaviour of something before imple
Stacey Roberts wrote:
>
> Hi Guys,
>I've just ordered FreeBSD V4.3, hoping to install it on a VP6 Dual proc
> system running two P111 933's.
>
> I've tried searching for known issues with this particular motherboard via
> all the search facilities at the FreeBSD sites, but cannot find any ac
Hi,
I found that some of the commands read the virtual memory of the kernel. Is there a
way for me to know which address of the memory is currently being accessed?
regards
ravi prasad
__
Your favorite stores, helpful shopping tool
[EMAIL PROTECTED] writes:
> we can probably try it out (if it seems really necessary for us)
> on KAME tree, but not on *BSD-current nor *BSD official releases.
I believe one of the intended uses of this would be for
telnet/rpcbind, so I think it would really have to go into
*BSD-curr
>@@ -964,7 +957,7 @@ sendorfree:
> /* clean ipsec history once it goes out of the node */
> ipsec_delaux(m);
> #endif
>- if (error == 0) {
>+ if (error == 0 && ia) {
> /* Record statistics for this interface address. */
>
[Bcc'ed to -net]
On http://people.freebsd.org/~dcs/ip_output.c there is a port to stable
of the revisions 1.127 through 1.130 of /sys/netinet/ip_output.c. These
patches do the following:
1) Enable one to send multicast packets without a default route or
routes to the multicast addresses.
2)
dear all
i have 2 freebsd-20010710-stable box "A" & "B", all same hardware
compaq-1600 + 3c905c-TX connect to switch, switch connect to router
so the seting is easy all defaultroute is the router.
it works great.
But suddenly box "A" frequentl lost default route
it happen less in 2 minute, and to
So I have an SMC 8040TX pccard in an IBM Thinkpad 701CS. It is
currently using the ed driver to talk on the network and this
driver works ok (I can get 5+ Mb/sec outbound), but the performance
problem is that I only get < 1Mb/sec inbound. So I have two
questions, 1) is the ed driver the correc
Bill Fenner wrote:
> It looks like the patch causes packets not to be sent if
> ia == 0. The inner part of the sendorfree: loop went from
>
> if (error == 0) {
> update if stats
> call if_output
> }
>
> to
>
> if (error == 0 && ia) {
>
Bill Fenner wrote:
>>@@ -964,7 +957,7 @@ sendorfree:
>> /* clean ipsec history once it goes out of the node */
>> ipsec_delaux(m);
>>#endif
>>- if (error == 0) {
>>+ if (error == 0 && ia) {
>> /* Record statistics for this int
Hi,
I'm using VLANs (IEEE 802.1q taggig) with the fxp driver. In the past (up
to 4.3 RELEASE and STABLE) the was a patch nessesary to get the MTU up to
1500 Bytes on the vlan-interfaces. I was using the patch found on
http://www.euitt.upm.es/~pjlobo/fbsdvlan.html. This patch looks outdated, I
On Thu, Aug 02, 2001 at 12:57:09PM -0500, [EMAIL PROTECTED] wrote:
>
>
> I have been combing the freebsd.org site for the last two days
> attempting to find some documentation on how to configure and use a
> FreeBSD server as a router. I have found some information on
> configuring the server a
14 matches
Mail list logo
