Hi all,
Is there a way to reset the root passwd without reinstalling FreeBSD 4.7.
Thanks in advance
Aman
___
freebsd-hackers@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
To unsubscribe, send any mail to "[EMAIL P
al Message ----- From: "Amandeep" <[EMAIL PROTECTED]>
I am instalaling FreeBSD 5.3 AMD 64 bit with 6- 200GB drives. Using
Higpoint 1820A controller and doing RAID 10. I am using drivers for
the card from Highpoint Web.
The problem is when I make the partitions and the machine tries to
al Message ----- From: "Amandeep" <[EMAIL PROTECTED]>
I am instalaling FreeBSD 5.3 AMD 64 bit with 6- 200GB drives. Using
Higpoint 1820A controller and doing RAID 10. I am using drivers for
the card from Highpoint Web.
The problem is when I make the partitions and the machine tries to
Hi guys,
Anyone???
Amandeep wrote:
Hi all,
I am instalaling FreeBSD 5.3 AMD 64 bit with 6- 200GB drives. Using
Higpoint 1820A controller and doing RAID 10. I am using drivers for
the card from Highpoint Web.
The problem is when I make the partitions and the machine tries to
format the
Hi guys,
Anyone???
Amandeep wrote:
Hi all,
I am instalaling FreeBSD 5.3 AMD 64 bit with 6- 200GB drives. Using
Higpoint 1820A controller and doing RAID 10. I am using drivers for
the card from Highpoint Web.
The problem is when I make the partitions and the machine tries to
format the
Hi all,
I am instalaling FreeBSD 5.3 AMD 64 bit with 6- 200GB drives. Using
Higpoint 1820A controller and doing RAID 10. I am using drivers for the
card from Highpoint Web.
The problem is when I make the partitions and the machine tries to
format the partitions it says:
unable to find dev
28.00 124 15.47 0 0 6 0 94
Thanks for your help and replies.
A
Eric Anderson wrote:
Amandeep wrote:
Hi all,
I am using Tyan S2098 MB with 160GB Maxtor ATA Drive and the
transfer rate is very low. FreeBSD 5.3-Release.
Any ideas what is going on here.
The transfer rate is about 15MB/s
when I
Hi all,
I am using Tyan S2098 MB with 160GB Maxtor ATA Drive and the transfer
rate is very low. FreeBSD 5.3-Release.
Any ideas what is going on here.
The transfer rate is about 15MB/s
when I run
#dd if=/dev/zero of=/usr/junk bs=8192
then do
#iostat 1
___
Amandeep wrote:
Hi again,
I have two Seagate SCSI drives 36GB and 8GB RAM and installed 5.3-REL
with
PAE and SMP support.
Now the problem arises that the system hangs under heavy load and there
are no error messages nothing. I have to hard boot it everytime it hangs.
Then I tried with only SMP
Hi all,
What Compaq SCSI Raid controllers run solid on FreeBSD 5.X..
Thanks in advance
A
___
freebsd-hackers@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
still hangs. I tried using
New memory and a Maxtor 36Gb SCSI drive , still hangs but was up for
longer perios 13hrs..
Any one know about this problem.
Alos tried with 5.4-Prerelease same results.
Any help would be great,
Scott any help.
Thanks
Aman
Rojer wrote:
Amandeep Pannu wrote:
Hi all,
I have
Hi daniel,
Josseph in this mailing list responded that I can do
ifconfig em1 alias inet 205.229.165.8 netmask 255.255.255.255
Can I?
I need the other NIC for some internal operations.
> On Fri, 18 Mar 2005 06:47, Amandeep Pannu wrote:
>> Now the em0 nic is up with 205.229.165.
Hi Guys,
Anything on this.
Any help would be great.
Thanks
A
> Hi
>
> I have a machine running FreeBSD 5.0 , it is actually my Primary DNS
> server.
> it has two Nics.
> em0 and em1
> Now the em0 nic is up with 205.229.165.4 netmask 255.255.255.0
>
> When I try to do
> ifconfig em1 inet 205.229.1
Hi
I have a machine running FreeBSD 5.0 , it is actually my Primary DNS server.
it has two Nics.
em0 and em1
Now the em0 nic is up with 205.229.165.4 netmask 255.255.255.0
When I try to do
ifconfig em1 inet 205.229.165.8 netmask 255.255.255.0 up
it say File exists.
then i read that the netmask sh
Hi Roger,
I installed the FreeBSd 5.3-Rel and also FreeBSd 5.2.1, no luck.
Now the kernel GENERic file shows bge # 570XX
I think these are different BCM5721.
Any clues.
Thanks
A
> Amandeep Pannu wrote:
>
>> 2) It doesnt detect the broadcom interfaces.
>>
>> They are
Hi all,
I am trying to install FreeBSD 5.3 on Tyan 5350 MB with 40GB ATA Maxtor
drive.
Two issues
1) It doesnt detect the ATA drive but When I boot under safe then it does
detect it and goes through installation.
2) It doesnt detect the broadcom interfaces.
They are
Broadcom BCM5721 PCI Express G
Hi all,
I have two Seagate SCSI drives 36GB and 8GB RAM and installed 5.3-REL with
PAE and SMP support.
Now the problem arises that the system hangs under heavy load and there
are no error messages nothing. I have to hard boot it everytime it hangs.
Any ideas what is going on.
It is a Supermicro
Hi Jason
> On 03/14/05 15:34:59, Amandeep Pannu wrote:
>> Hi Kris,
>>
>> I had this problem before and I changed the MB and the memory and
>> today it
>> did the same thing it did before.
>> memtest doesnt give any errors.
>>
>> Thanks
>> A
Hi Kris,
I had this problem before and I changed the MB and the memory and today it
did the same thing it did before.
memtest doesnt give any errors.
Thanks
A
> On Mon, Mar 14, 2005 at 12:23:59PM -0800, Amandeep Pannu wrote:
>>
>> HI all,
>>
>> I am running Fre
HI all,
I am running FreeBSd 5.3-REL
Today my system simply locked up. There was no error sent to console, to
any logs, nor the monitor screen. It was totally unresponsive to network,
serial console, or keyboard. After 4 power-cycles, we were unable to get
past the BIOS as it was reporting "R
Hi all,
I am encountering these SCSI errors with FreeBSD 5.3-REL-p5
Any ideas what is going on.
ahd0: port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc30-0xfc301fff irq 28
at device 2.0 on pci3
ahd0: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
ahd1: port
0
Hi Scott,
I am encountering these errors wiht FreeBSD 5.3-REL-p5
Any ideas what is going on.
ahd0: port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc30-0xfc301fff irq 28
at device 2.0 on pci3
ahd0: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
ahd1: port
0x48
Hi Scott,
Is there any SCSi RAID controller that works on FreeBSD 5.3 Release.
I have tried a couple.like
Adaptec 2120S
Adaptec 39320A
Megaraid LSI-320-1
None of them worked.
Any clues. They are under the HCl for FreeBSD 5.3.
My configuration is two drives wiht RAID-1. I am using X6DHP-8G SM MB
Hi all,
Seems like a dumb question but how do i upgrade FreeBSD 5.3-Release to
FreeBSD 5.3-Release-p5.
I am very new to this stuff. Not even know if I am posting in the right
mailing list.
Thanks in advance
A
___
freebsd-hackers@freebsd.org mailing li
Hi all,
I have this Supermicro MB P4SCI and I am using the onboard SATA
controllers and making a RAID of two Seagate 80Gb SATA drives but when I
try to install FreeBSD 4.11 it doesnt see the drives configured as RAID.
Any ideas as if this is supported or not.
If I try single drives wihout RAID i
Hi all,
Thanks all for your replies. I installed 5.3 which saw the whole 2.2TB in
sysinstall then I made two slices and mounted them.
Everything worked fine.
Thanks again.
Kudos to 5.3
Aman
>> I am new to this big arrays. FreeBSD 5.2.1 doesnt see all the 2.2TB.
> So am I, and I had the same probl
I am new to this big arrays. FreeBSD 5.2.1 doesnt see all the 2.2TB.
So when I do
# dmesg |grep da0
GEOM: create disk da0 dp=0xc832fc50
da0 at twa0 bus 0 target 0 lun 0
da0: <3ware Logical Disk 00 1.00> Fixed Direct Access SCSI-0 device
da0: 100.000MB/s transfers
da0: 2384080MB (4882595840 512 byt
Hi all,
I have 12WD 200GB SATA drives with RAID5 and glabal spare on 3ware 9000
series controller. Also one 80GB SATA drive for OS.
I had to manually compile the twa driver. kldload twa. The system started
recognizing the controller and the total capacity.
Although the dao show 2.2TB but when I t
28 matches
Mail list logo
