[Elecraft] K160RX K2 160 Meter and 2nd Ant Option SOLD

K160RX K2 160 Meter and 2nd Ant Option SOLD Sent from Mail for Windows 10 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This

[Elecraft] K160RX K2 160 Meter and 2nd Ant Option for sale

UNBUILT K160RX K2 160 Meter and 2nd Ant Option kit for sale. Parts inventoried this AM. Complete. You get to build it. Another closet find! $75 includes shipping US. Contact off list for payment options. 73 de Ben W4SC Sent from Mail for Windows 10 _

Re: [Elecraft] K160Rx protection

Hans, The K2 RX ANT is injected at the same point after the T/R switch and before the Low Pass Filter, so any energy from the transmit antenna will not harm the K2 during transmit, although it may add to the RF level going into the LPF and be amplified by the KPA100. 73, Don W3FPR On 4/1/20

[Elecraft] K160Rx protection

Hello My K2/K100 complain and wants to get on the air. I plan to use the build-in K160RX antenna switch for a separate rx antenna, which is about 10m /30 feet from my tx antenna. Plan to run 100 W. Tx antenna is a vertical. Rx antenna is a low (1 m above grd) horizontal dipole. Do I have to in

Re: [Elecraft] K160RX

g9hfr...@gmail.com Sent: Saturday, August 13, 2016 1:46 AM To: elecraft Subject: [Elecraft] K160RX Anyone have a K160RX <http://www.elecraft.com/k2_page.htm#K2 Options> they want to get rid of? KG9H __ Elecraft mailing list

Re: [Elecraft] K160RX

Frank, Don't forget that in addition to the K160RX board, you will need the capacitors for the 80/160m bandpass filter, the standoff, the header (it is taller than normal) and the BNC jack. There is more to the K160RX kit than just the board. The Elecraft kit has all the components required

[Elecraft] K160RX

Anyone have a K160RX they want to get rid of? KG9H __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elec

[Elecraft] K160RX K2 second antenna

Anyone looking to upgrade your K2 - I have for sale on eBay a K160RX kit. The bids starts at $12.00 plus flat rate shipping. Dave Little, AF5U __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http:/

Re: [Elecraft] K160rx installation problem

Dan, First try a simple solution - turn the power control back to 12 watts and try a TUNE. If you still get HiCur messages, then check the low pass filter on the K160RX carefully - count the number of turns on the toroids - each pass of the wire through the center of the core counts as one turn

[Elecraft] K160rx installation problem

Hi - I've just installed the K160RX module in my K2, and I cannot align it: trying to do so on transmit gives "HiCur" readout no matter what I do. I've even tried boosting the Cal Cur menu option: still no dice. It looks like a very simple circuit, and it does fine on 80m. Any suggestion

RE: [Elecraft] K160RX

> > Group , I am suppose to align the 160 module using CAL PLL. > I have the band on 160 with the VFO at 1800.1. > Using CAL PLL at TP1 I get the INFO 232 message that CALL PLL > should be done > on 40 meters. > Need help. > > Glenn > K5ZE > Hi Glenn! K160RX manual rev D states: "The following s

Re: [Elecraft] K160RX

Glen Look for an errata sheet for the K160RX. Turns out that the CAL PLL is done on 40m only these days. Good luck and 73 Bob N6WG - Original Message - From: "Glenn Haffly" <[EMAIL PROTECTED]> To: Sent: Sunday, February 10, 2008 9:19 AM Subject: [Elecraft] K160RX > G

[Elecraft] K160RX

Group , I am suppose to align the 160 module using CAL PLL. I have the band on 160 with the VFO at 1800.1. Using CAL PLL at TP1 I get the INFO 232 message that CALL PLL should be done on 40 meters. Need help. Glenn K5ZE ___ Elecraft mailing list Po

[Elecraft] K160RX WANTED

ANYBODY GOT A K160RX FOR SALE BYRON / N4AX ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft

RE: [Elecraft] K160RX alignment question

Hank, Read the K160RX errata sheet - it tells you not to do the CAL PLL on 160 meters. The display you received is quite normal when attempting CAL PLL on any band except 40 meters, so no harm done. The frequency that is briefly displayed the the frequency of the VCO output (read from TP1). It

Re: [Elecraft] K160RX alignment question

Hi Hank, Look at the Errata for your module. I always incorporate the errata into the manual before I start building, just to make sure I don't miss anything. If you didn't get the errata you can download it from Elecraft's website. In any case, it states that you don't need to do the firs

[Elecraft] K160RX alignment question

My construction of the K2 is progressing, SSB and noise limiter are installed and I installed the 160 M module this afternoon. Just after sunset the 160 meter band was full of activity. I have a concern about the 160 meter alignment. Manual page 9. step 2. Set VFO for 1800.10 kHz Select CAL P

RE: [Elecraft] K160RX

Ken, Install the parts and header (and don't forget the standoff). It will not interfere with the rest of the alignment (if done correctly). 73, Don W3FPR > -Original Message- > Hi everyone, and seasons greetings. > Advice needed please. I have K2 number 5788 (new build) and have > hal

[Elecraft] K160RX

Today Ken Chandler g0orh wrote ... Advice needed please. I have K2 number 5788 (new build) and have half the RF board completed but no alignment or test in Part II, has been done yet ... I have K160RX module built and awaiting installation, can I install the module and ALL it's components, etc, o

[Elecraft] K160RX

Hi everyone, and seasons greetings. Advice needed please. I have K2 number 5788 (new build) and have half the RF board completed but no alignment or test in Part 11, has been done yet as I don't have Capacitors C31, 35, 122, or 228. Elecraft are dispatching those for me. I have K160RX module bui

[Elecraft] K160RX Hi Current

I just installed the 160 meter/rx antenna option and everything seems to be working fine...EXCEPT...when I try to tune on 160 I get first the Hi Current notice then .1 1.0-1nothing out. I've got a K2/100 connected to an Astron 30 amp power supply so I'm sure there's plenty of voltage. I can

Re: [Elecraft] K160RX (Long)

David, To repeat the old adage - check soldering, then re-check soldering, and when that is done, check the soldering. In particular, look for too much solder causing solder bridges. Plug the K160RX into the K2 and select any band other than 160 meters - then power off and check the resistan

[Elecraft] K160RX (Long)

Hello All I am posting this again. I have a problem with "HI CUR" On the K160RX It comes on for a second and then shows .5 watts regardless of the power setting. In troubleshooting here is what I have done I compared in and out of the of the module with the setup of Power 1.0 watts setting I got

Re:[elecraft] K160RX problem

Hi Don Thanks for that. 73 Bryan G3AKF ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help:

Re: Re[Elecraft]K160RX problem

Bryan, This is a residual step left over from the old days when CAL PLL was to be performed on all bands - it is no longer required, CAL PLL is only done with the K2 set to 40 meters - and as you experienced it will report an error if you attempt it on 160. Simply skip that step in the K160R

Re[Elecraft]K160RX problem

Hi All Tryng to do 160 Meter Alignment page 9. CALL PLL display shows 06917.1 and then Info 232. Any ideas will be appreciated. 73 Bryan G3AKF ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. S