[Discuss-gnuradio] Cannot Access new USRP2 from Ubuntu 9.10

Dear all, I have successfully installed the binary for GnuRadio 3.2.2-1 and gnuradio-compaion on Ubuntu 9.10. I have a new USRP2 Rev 4.0 with TVRX. The SD card is in, and lights D and F are on. I followed guidelines on USRP2UserFAQ (and reviewed previous posts), but am not able to connect to USR

Re: [Discuss-gnuradio] Cannot Access new USRP2 from Ubuntu 9.10

rd? If it's not eth0 > you have to specify the device (I think), for example: > > sudo find_usrps -e eth1 > > I wouldn't be surprised if your laptop's default ethernet port is not > gig-e, and is eth0. > > > On Mon, Feb 8, 2010 at 5:36 PM, Omid F wrote: &g

Re: [Discuss-gnuradio] Cannot Access new USRP2 from Ubuntu 9.10

are is up to date with your gnuradio install. > > -Josh > > > On 02/08/2010 02:57 PM, Omid F wrote: > >> Thanks for the prompt response Tom. >> >> I was running as root previously too. I tried again, no difference, I get: >> "No USRP2 found." &g

[Discuss-gnuradio] Firmware / FPGA bitstream for USRP2 Rev 4

Hi, I get a new Rev4 USRP2 two weeks ago, and have not yet been able to connect to it. I tried both the binary and the source code on different machines running different versions of Ubuntu (9.4, 9.10). I simply get "No USRP2 found." when I call find_usrps. I have reached a point that I am almos

Re: [Discuss-gnuradio] Firmware / FPGA bitstream for USRP2 Rev 4

Thanks for your response. Please find detailed explanations below. On Thu, Feb 11, 2010 at 8:50 PM, Matt Ettus wrote: > > On 02/11/2010 05:47 PM, Omid F wrote: >> >> Hi, >> >> I get a new Rev4 USRP2 two weeks ago, and have not yet been able to >> connect to i

Re: [Discuss-gnuradio] Firmware / FPGA bitstream for USRP2 Rev 4

USRP2, the ethernet interface on laptop is alive and at least it properly sends ethernet packets out upon each call to "fins_usrps." Very strange situation! Any help is highly appreciated. Omid On Fri, Feb 12, 2010 at 12:56 PM, Omid F wrote: > Thanks for your response. Please

Re: [Discuss-gnuradio] Firmware / FPGA bitstream for USRP2 Rev 4

Feb 13, 2010 at 3:17 PM, Matt Ettus wrote: > On 02/13/2010 12:49 PM, Omid F wrote: > >> I copied the latest txrx.bin and u3_rev3.bin on a new 256MB SD-card. >> Then I verified and made sure it is properly copied. Still no success. >> LEDs don't turn on. I also tried

Re: [Discuss-gnuradio] Firmware / FPGA bitstream for USRP2 Rev 4

I had tried that. Didn't help! Thanks though. Best Regards, Omid On Sun, Feb 14, 2010 at 11:05 AM, Firas Abbas wrote: > Hi, > > Did you put a static IP address in your Ethernet? > Tip, put any dummy static IP address, and you will find your USRP2!!! > > Best Regard, > > Firas > > __

Re: [Discuss-gnuradio] Firmware / FPGA bitstream for USRP2 Rev 4

all possible pause combinations as well (autoneg = on/off, rx=on/off, tx=on/off), but I get the same results. I apologize again for sending so many (long) emails. Thanks, Omid On Sun, Feb 14, 2010 at 5:03 PM, Eric Blossom wrote: > On Sat, Feb 13, 2010 at 11:38:27PM -0600, Omid F wr

[Discuss-gnuradio] Busy-waiting in ethernet_mac_miim_write()

Hi,After a lot of testing/debugging (previously in thread "Firmware / FPGA bitstream for USRP2 Rev 4") by using a re-compiled version of txrx.bin from the gnuradio firmware source code, I was able to find out where the firmware gets stuck: Regardless of whether the usrp2 is connected to a machine

[Discuss-gnuradio] Antenna for WBX?

Hi, I am not sure which of LP0410 or Vert400 to order with WBX? My application is creating a two-way communication between two USRP2s equipped with WBX over the unused TV frequencies. Thanks, Omid ___ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.