祝福,所有兄弟姐妹们
中国年快乐
At 2011-02-02 12:07:47，i...@agile-sdr-solutions.com wrote:
Agile Solutions is pleased to announce a new Wideband RF Transceiver board
U-RFX capable of tuning frequencies from 1MHz to 4.4GHz.
The wide frequency coverage addresses the need for single RF transceiver boar
Agile Solutions is pleased to announce a new Wideband RF Transceiver
board U-RFX capable of tuning frequencies from 1MHz to 4.4GHz.
The
wide frequency coverage addresses the need for single RF transceiver
board capable of meeting various application needs ranging from 1MHz to
4.4GHz with 50 MH
On 02/01/2011 01:40 PM, Achilleas Anastasopoulos wrote:
I am following the instruction for installing gnuradio companion on a
USRP E100.
I installed python-lxmx
The config/grc_grc.m4 patch does not seem to be relevant: I do not see
the line that I am supposed to changein any case bootstrap
I am following the instruction for installing gnuradio companion on a USRP
E100.
I installed python-lxmx
The config/grc_grc.m4 patch does not seem to be relevant: I do not see
the line that I am supposed to changein any case bootstrap and
configure work and report that grc will be build.
We have 4 used USRP1s and 1 USRP2s systems for sale. We don't have a need
for them anymore. The USPR1s were modified for external clock (with some
zero ohm changes it can be reverted back to its original 64MHz mode).
Each USRP1 can be purchased at $500.00 and USRP2 at $1000.00. I can take a
paypal
Hy Marcus, are you sure? I think the problem is related to the setting of
parameters of the USRP2 like decimation, interpolation, sample time, etc. ..
However I try to follow your advice and post in a public maining list you
suggested. Thank you very much.
If you aren't using Gnu Radio to set tho
Hy Marcus, are you sure? I think the problem is related to the setting of
parameters of the USRP2 like decimation, interpolation, sample time, etc. ..
However I try to follow your advice and post in a public maining list you
suggested. Thank you very much.
Marcus D. Leech wrote:
>
> On 02/01/20
Hi everyone,
I thought I had a problem with my FPGA image, but the led F
means that the FPGA is well programed. The led E would mean that the FPGA have
load the firmware. I compiled the raw internet version of the FPGA with ISE
10.1 and i tried it with Raw Ethernet firmware
On 02/01/2011 04:14 AM, nyquist82 wrote:
> Then, I use Windows Storage Server 2003, an Agilent N9010A spectrum analyzer
> that uses the 89601 VSA software. Attached to the message two Simulink
> models. The first run the signal receiving and recording in a file, the
> second forward to the analyzer
The website (and git server) is back up. I will try to figure out
what's causing these frequent crashes lately.
Tom
On Tue, Feb 1, 2011 at 4:34 AM, Martin Braun wrote:
> On Tue, Feb 01, 2011 at 10:09:53AM +0100, Fabian Klaes wrote:
>> Dear list,
>>
>> when trying to clone gnuradio from git i go
Hey, Patrick,
I found the idea in this post to the list-
http://www.mail-archive.com/discuss-gnuradio@gnu.org/msg28487.html
which led to this-
http://hackaday.com/2005/11/08/using-a-tv-tuner-as-a-high-speed-adc/
which led to this-
http://www.domenech.org/bt878a-adc/index-e.htm
The cards are ol
All,
Ah, thats embarrasing :-/, must remember to restart the USRP.
Thanks for the replies,
Philip
From: Nick Foster
To: Philip Apus
Cc: Discuss-gnuradio@gnu.org
Sent: Mon, 31 January, 2011 18:20:03
Subject: Re: [Discuss-gnuradio] N210 firmware
On Mon, 2011
Hello ,
i also did the same thing and got the same error but could not figure out
what is the problem as gnu core is there in gnu radio folder ans still
getting this error. how could i get rid of this.
Regards,
Niaz
Martin Braun-4 wrote:
>
> On Fri, Apr 09, 2010 at 04:04:30AM -0700, Berk wrot
schrieb George S. Williams am 2011-01-27 17:38:
> Is it possible to increase the maximum sampling rate for audio_alsa?
>
> I am experimenting with using a modified TV tuner card as an ADC. The
> card uses a Bt878a chipset. arecord can record from the card at 1972000
> rate and GRC shows the maximu
On Tue, Feb 01, 2011 at 10:09:53AM +0100, Fabian Klaes wrote:
> Dear list,
>
> when trying to clone gnuradio from git i got this:
>
> git clone http://gnuradio.org/git/gnuradio.git
> Initialized empty Git repository in /home/fs/gnuradio/.git/
> error: while accessing http://gnuradio.org/git/gnur
Then, I use Windows Storage Server 2003, an Agilent N9010A spectrum analyzer
that uses the 89601 VSA software. Attached to the message two Simulink
models. The first run the signal receiving and recording in a file, the
second forward to the analyzer through USRP2.
How should I set the parameter
Dear list,
when trying to clone gnuradio from git i got this:
git clone http://gnuradio.org/git/gnuradio.git
Initialized empty Git repository in /home/fs/gnuradio/.git/
error: while accessing http://gnuradio.org/git/gnuradio.git/info/refs
fatal: HTTP request failed
also, when i try to access a
17 matches
Mail list logo
