On Fri, Jan 08, 2010 at 07:24:14PM +, nadia raj wrote:
>
> Hi,
> I wanted to ask you that if i want to send two independent data streams to
> two daughter boards mounted on one usrp, wats the command for it.
> If i want to explicitly send data1 to sub(0,0) and data 2 to subdev(0,1)
> SIMULTANE
Hi,
I wanted to ask you that if i want to send two independent data streams to
two daughter boards mounted on one usrp, wats the command for it.
If i want to explicitly send data1 to sub(0,0) and data 2 to subdev(0,1)
SIMULTANEOUSLY..then how do you do it?
I have read few examples but im not able
On 01/08/2010 06:33 AM, Yan Nie wrote:
Hello,
I'm looking for the schematic and layout map for USRP1, but I cannot
find the schematic at the download page of http://www.ettus.com/download .
Could you please tell me where can I get the the schematic and layout
map of USRP1.
Thank you so much!
Yan
The script expects a file named u2_rev3.ise not xise. Perhaps that is
confusing it. Try changing the name in the u2_rev3/Makefile
-Josh
Mahesh Poolakkaparambil wrote:
Hello,
As an update to prior query,I tried here to make bin file using CLI in Linus
I got the following errors,
Creating proje
Thank you Matt and Tim. How about the USRP FPGA/FX2 Interface, FPGA/CODECs
Interface, and CODECs/FX2 Interface? Where can I get these?
I saw them in the previous gnuradio website, but didn't download them. I cannot
find them in the new gnuradio web.
Thank you so much
Yan
___
Hello,
As an update to prior query,I tried here to make bin file using CLI in Linus
I got the following errors,
Creating project: build/u2_rev3.ise
ERROR:TclTasksC:project_087: Project file
"/scratch/src/gnuradio/usrp2/fpga/top/u2_rev3/build/u2_rev3.xise" already
exists. Use [project open
"/scratc
Dear all,
I was trying to run the usrp2 project on ISE v 11.1. My
project compilation fails with errors as follows,
Error: MapLib : 30 - LOC constraint V15 on PHY_CLK is invalid : no such site
on the device. to bypass this error set the environment variable
'XIL_MAP_LOCWARN '.
there
Hello,
I'm looking for the schematic and layout map for USRP1, but I cannot find the
schematic at the download page of http://www.ettus.com/download .
Could you please tell me where can I get the the schematic and layout map of
USRP1.
Thank you so much!
Yan
_
On Fri, Jan 08, 2010 at 11:00:22AM +0100, Hanno Jung wrote:
> Hi,
>
> if you're trying to tune to 1100 Hz this should be too low for an rfx 1800.
>
> With that daughterboard try somethinf around 1800 whithout commas.
> I don't know if this format is supported.
>
set_tx_center_freq expects a fre
Hi George,
I was looking for BBN & USRP2 information at the list when I saw your
message. I'm interested on get interoperability with 802.11 cards in
monitor mode, but I still haven't had success. Could I make you some
short questions?
- Which modification did you do to the transmission filter?
Browsing the code and testing, I've found the way to run propertly BBN
examples.
Modifying the method SENDPKT_TO_PHY from the "bbn_80211b_pkt.py" file,
not allowing shor preamble (short_preamble=0), when I transmit "Hello
World" as a payload, receiver can detect propertly the packets.
Usage:
On on
Hi,
if you're trying to tune to 1100 Hz this should be too low for an rfx 1800.
With that daughterboard try somethinf around 1800 whithout commas.
I don't know if this format is supported.
2010/1/8 srinivas naga vutukuri
> Daughter Board: RFX 1800
> what is the range i should have to provide
12 matches
Mail list logo
