Dear Debian users,
Hopefully you can easily help me with my confusion.
I would like to collect / keep core dumps in the system. For that I use
systemd-coredump package which is configured as following:
=== cut /etc/systemd/coredump.conf ===
[Coredump]
Storage=external
MaxUse=5G
=== cut ===
The
On 2019-12-18, Anthony DeRobertis wrote:
>
> Another option might be to use Network Manager, I think its connections
> can set a custom MTU, but I'm not 100% sure as I've never tried it.
I've used tethering successfully with Network Manager but never had
occasion to alter the mtu settings.
Why
On Wed, 18 Dec 2019 02:30:01 -0500
Anthony DeRobertis wrote:
> On 12/17/19 11:39 AM, Celejar wrote:
> >
> > Now I just have have to figure out the best place to configure this.
> > I'm using dhcp via /etc/network/interfaces, but the 'dhcp' method
> > doesn't seem to support manual MTU setting. I
On Wed, 18 Dec 2019 10:59:11 - (UTC)
Curt wrote:
> On 2019-12-18, Anthony DeRobertis wrote:
> >
> > Another option might be to use Network Manager, I think its connections
> > can set a custom MTU, but I'm not 100% sure as I've never tried it.
>
> I've used tethering successfully with Netw
Celejar writes:
> I'm not that familiar with the internals, but basically, the phone
> presents a wifi access point, the computer connects to it as it would
> to any AP, and the phone apparently routes packets to and from the
> cellular network.
Yes, I know that. However, the packets are being en
This may be what you have:
https://en.wikipedia.org/wiki/IPv6#IPv4-mapped_IPv6_addresses
--
John Hasler
jhas...@newsguy.com
Elmwood, WI USA
Celejar writes:
> It does work (and to automate it, I'll probably put it in e/n/i with a
> post-up line) - I'm just looking for the "right" way to do it (and to
> undo it on connection down, as I discussed in another message in this
> thread).
I wouldn't worry about doing it the *right* way. It's
Hi everybody,
Following the instructions reported on the Debian unofficial port
home-site [1] I successful installed Debian on raspberrypi 3B 2016 all
works fine for my needs but configuring the built-in wi-fi interface
apparently it works but reporting errors:
~# ip addr show dev wlan0
3: wlan0:
On Wed, 18 Dec 2019 16:28:40 +0100
Franco Martelli wrote:
> Hi everybody,
>
> Following the instructions reported on the Debian unofficial port
> home-site [1] I successful installed Debian on raspberrypi 3B 2016 all
> works fine for my needs but configuring the built-in wi-fi interface
> appare
Aside / Admission: I don't backup all that I should and as often as I should,
so I'm looking for ways to improve. One thought I have is to write my own
backup "system" and use it, and I've thought about that a little, and provide
some of my thoughts below.
A purpose of sending this to the mail
It depends what do you want to backup. If that is code, or text files, use
git. If they are photos videos or mostly binary, use some script and
magnetic tapes.
Levente
On Wed, Dec 18, 2019, 18:03 wrote:
> Aside / Admission: I don't backup all that I should and as often as I
> should,
> so I'm
On 18/12/2019 17:02, rhkra...@gmail.com wrote:
Aside / Admission: I don't backup all that I should and as often as I should,
so I'm looking for ways to improve. One thought I have is to write my own
backup "system" and use it, and I've thought about that a little, and provide
some of my thoughts
On Wed, Dec 18, 2019 at 12:02:56PM -0500, rhkra...@gmail.com wrote:
> Aside / Admission: I don't backup all that I should and as often as I should,
> so I'm looking for ways to improve [...]
> Part of the reason for doing my own is that I don't want to be trapped into
> using a system that might
On 18/12/19 at 17:32, Nektarios Katakis wrote:
>
> You should try to associate the wireless nic with your wifi by running
> only wpa_supplicant to see if that succeeds (the link state should
> change - the mode in the `iwconfig` command should be managed).
>
> For example this is how my config lo
On Wed, 18 Dec 2019 10:27:51 +0300
Reco wrote:
> Hi.
>
> On Tue, Dec 17, 2019 at 04:54:17PM -0500, Celejar wrote:
> > But the IPv6 address e:f:g:h:i:j:k:l is not actually configured
> > anywhere on the router (as shown by 'ip a' and other tools)!
>
> Either there's some IPv6 - IPv4 conver
On Wed, 18 Dec 2019 07:41:21 -0600
John Hasler wrote:
> This may be what you have:
> https://en.wikipedia.org/wiki/IPv6#IPv4-mapped_IPv6_addresses
Thank you. As per my other mail, it turns out that it's apparently this:
https://en.wikipedia.org/wiki/IPv6_transition_mechanisms#NAT64
https://en.w
On Wed, 18 Dec 2019 07:47:18 -0600
John Hasler wrote:
> Celejar writes:
> > It does work (and to automate it, I'll probably put it in e/n/i with a
> > post-up line) - I'm just looking for the "right" way to do it (and to
> > undo it on connection down, as I discussed in another message in this
>
On Wed, 18 Dec 2019 07:29:08 -0600
John Hasler wrote:
> Celejar writes:
> > I'm not that familiar with the internals, but basically, the phone
> > presents a wifi access point, the computer connects to it as it would
> > to any AP, and the phone apparently routes packets to and from the
> > cellu
Celejar writes:
> I assume the phone first just routes them from wifi to cellular. I'm
> not familiar with how it then transmits them over the cellular link.
It has to encapsulate them in some way for the cellular protocol.
> Yes, but that happens with virtually all this machine's network
> conne
If you don't to reinvent the wheel, and have more than one computer to
backup...
try Bacula www.bacula.org
does everything you want
On 19/12/19 3:02 am, rhkra...@gmail.com wrote:
Aside / Admission: I don't backup all that I should and as often as I should,
so I'm looking for ways to improve
On Wed, 18 Dec 2019 13:58:38 -0600
John Hasler wrote:
> Celejar writes:
> > I assume the phone first just routes them from wifi to cellular. I'm
> > not familiar with how it then transmits them over the cellular link.
>
> It has to encapsulate them in some way for the cellular protocol.
>
> > Y
Thanks to all who replied!
This script (or elements of it) looks useful to me, but I don't fully
understand it -- I plan to work my way through it -- I have a few questions
now, I'm sure I will have more after I get past the first 3 (or more
encouraging to me, first 6) lines.
Questions below:
On Wed, 18 Dec 2019 12:02:56 -0500
rhkra...@gmail.com wrote:
> Aside / Admission: I don't backup all that I should and as often as I
> should, so I'm looking for ways to improve. One thought I have is to
> write my own backup "system" and use it, and I've thought about that
> a little, and provid
rhkra...@gmail.com wrote:
...
>> if test -z "$home" -o \! -d "$home" ; then
>
> What does the -o \! do -- hmm, I guess \! is a bash "refeence" to the owner
> --
no, -o is logical or in that context.
the backslash is just protecting the ! operator
which is the not operator on what follows.
Celejar writes:
> ...the problem only occurs when tethering.
Which is the only time the cellular encapsulation is being done.
--
John Hasler
jhas...@newsguy.com
Elmwood, WI USA
On 2019-12-18 09:02, rhkra...@gmail.com wrote:
Aside / Admission: I don't backup all that I should and as often as I should,
so I'm looking for ways to improve. One thought I have is to write my own
backup "system" and use it, and I've thought about that a little, and provide
some of my thoughts
On Mi, 18 dec 19, 18:34:03, Franco Martelli wrote:
>
> Thanks for your answer I've just solved thank reading this link [1] it
> was the gateway line once commented all work fine. Now the wlan0
> configuration file is:
Apparently with ifupdown[2] you can't have the same default gateway for
severa
27 matches
Mail list logo
