Hi everybody
I',m not sure if this is the right place to put a quetion like this, but
here it is.
I ned some information about the structure of a floppy and how both to
read and to foramt it at a low level. Of couser under linux, but also
under DOS (I've got some doc on how DOS works with floppie
About the boot manager I can't say nothing more, just read all the doc
available on
this subject. By the way you can find tons of documentation in every debian's
ftp
site, just lok for '.../LDP' directory. There's the Linux Documentation
Project. Under
this project was release a quick start manu
Hello:
I need to pass some aic7xxx parameters at boot promt of the rescue
disc and I'm not sure about the syntax. Is the following line correct:
linux aic7xxx_reset_delay=15 aic7xxx_tagged_queuing=on
aic7xxx_proc_stats=off
?
I'll thank any additional information on this subject.
Thanx in advanc
Hello:
I'm a poor spanish newbie in this waters but I don't see any reply to
your message in the list, so here is my help:
I can't say so much about your system 'cos I'm a PC user, but this could
help:
1.- See the Linux Hardware Compatibility HOWTO to check if all your
hardware is supported. You
Hello list:
I've got a ZIP-100 parallel port dirve and a LS-120 internal unit.
I've installed Slink (kernel 2.0.36) but I couldn't set up the ppa.o
module for the zip during the installation (I'll thank any help on this
matter. The lp.o module was installed with the default parameters).
The probl
There's a SCSI-HOWTO in the HOWTO's. Look for it in http://www.linux.org
Sorry for the delay.
___
Even God discusses the details with the devil (anonymous).
Antonio A. Rivas [EMAIL PROTECTED]
STARTEG Project [EMAIL PROTECTED]
marc escribió:
>
> where can i get more information regarding
I've installed Slink and when I tried to set up the ppa parameters I'd
got an error an the zip was not installed. Now I must to install it from
the command line. Any help will be regreted. My system's got just one
parallel port at 0x378 irq7
Mike Merten escribió:
>
> On Mon, Feb 08, 1999 at 07:59
ilar problem with an
AHA-2940UW and a SEAGATE ST34520W hard drive.
Thank you anyway
Antonio A. Rivas [EMAIL PROTECTED]
--
Even God discuss on the details with the devil
STARTEG Project [EMAIL PROTECTED]
--
-Mensaje original-
De: Richard Hall <[EMAIL PROTECTED]>
Para: Antonio
Hi
I've got an 2940UW to and I've got a similar problem with it. I've tried
almost everything since the past December and the problem still goes on. My
system hangs at the detection phase of the HD attached to the card (it's the
only device attached to the card). I get a timed out error.
If you g
>> a) It's closer to the natural language than C and, of course, C++, and
all
>> of us think in our own natural language (english, spanish, french,
german,
>> etc...) and this is the first language we use when we develope a program.
>
>This can also be a disadvantage, because programming _is_ much
>
>I think that it is worth considering skipping the Pascal stage and
>going straight to C, or equivalent languages. Taking this approach a bit
>further, I think it is even worth considering going straight to C++,
>perhaps
>by talking first about the procedural aspects of C++ and only then, as a
>s
Saludos, tocayo
Agradezco mucho el tiempo que te has tomado para darme una solución al
problema, pero me parece que oyes campanas y no sabes dónde, seguramente por
mi tendencia a hacer literatura en lugar de dar información.
Aclarar que dispositivos SCSI sólo tengo el disco duro, la zip e
-Mensaje original-
De: Antonio A. Rivas Ojanguren <[EMAIL PROTECTED]>
Para: John C. Ellingboe <[EMAIL PROTECTED]>
Fecha: miércoles, 06 de enero de 1999 05:24 p.m.
Asunto: RE: Amazing installation. SCSI problems
>Hi John
>
>You are right, I don't ha
-Mensaje original-
De: Antonio A. Rivas Ojanguren <[EMAIL PROTECTED]>
Para: Marcelo E. Magallon <[EMAIL PROTECTED]>
Fecha: miércoles, 06 de enero de 1999 05:23 p.m.
Asunto: RE: TO-TH : Conflictos SCSI.
>>No. Me refiero a todos. Incluso el disco duro. (Estás tratando
Thanx John
But as I've said in my previous e-mail I'm new here and I don't know the
ways to deal with debian as well as you think.
Can you tell me how can I set up the driver?
Greetings from Spain.
Antonio A. Rivas Ojanguren
[EMAIL PROTECTED]
>Hey Antonio,
>
&
Heavy
Xmas to all of you
I'm new
in linux but not in dealing with the installation process of an OS (DOS, OS2,
WINDOWS 9x,..), but Debian defeats me.
First
some technical data about my system:
-
Processor: i486 dx4-100
- Motherboard: VLB-PCI,
American Megat
16 matches
Mail list logo