Stus-List thanks for all your effort

Stu, I manage numerous sites and locations so I know the amount of effort this takes. I want to make sure you know the pleasure (and value) I get from this site . thanks for all your help George Cone C &C 40 - LaVida ___ This List is provided by th

Stus-List c&C 24 rudder detail

Ed, I am based in Burlington too, and I also have the details of water in the rudder (on a 40), I drilled the 2 holes, one at the top and one in the bottom in the fall(so that it could possibly drain better, it was still weeping last weekend when I sealed the holes back up for the summer, I'll pro

Stus-List Set up of shower in Cockpit

I wanted to run a thought by the list to see if my thoughts to install a small handheld shower in the back of the cockpit for rinse of and showering at the area of the wheel are feasible. My positive reasons for this is extra room and ease of draining and overall cleaning. I am considering connecti

Stus-List cockpit shower

The recirculating pump I mentioned is the pump that pulls the water from the engine and circulates it through the heat exchanger within the water heater. I am surprised the engine has a thermostat as high as 160 degrees. It is raw water cooled. 160 degrees sounds like my shower would be good for co

Re: Stus-List IPad Question...

Or you can get a vanilla android tablet for $80- $100 that has built in GPS and do the same thing and not worry if it gets wet. Thanks, George C&C 40 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Dennis C. via CnC-List Sent: Friday, October 02, 2015 11:18 AM To: CnClis

Re: Stus-List IPad Question...

Sure, what year type ipod George C&C 40 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of David via CnC-List Sent: Friday, October 02, 2015 1:12 PM To: CNC CNC Cc: David Subject: Re: Stus-List IPad Question... Anybody wanna trade a 64GB IPad for a Vanilla Android with

Re: Stus-List Got a New 135% Head Sail

I picked up a new headsail - 135% furling for my C&C40 last year. The quality, design was very high, all the features were included, for a little less than what you spent, I compare it to the Rolly mail from the fear before and it is just as good. It was the challenge Marblehead fabric George

Re: Stus-List Emergency Tiller Bracket Squeaking

On my 40 I had the same problem, the steering became very “tight” or “hard”, I tied to add grease thru the fitting into the lower tube bad it was too far gone I guess, the yard at considerable expense had four guys pulling the rudder down after the quadrant and all had to be taken off, the rudde

Re: Stus-List Emergency Tiller Bracket Squeaking

I needed to add that I removed the top bearing you describe, and it helped a little but only for short times and was not successful, it actually comes our quite easy, just nuts and bolts and slides out the top. George C&C 40 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of

Re: Stus-List C&C 37+ Repower -- Ugh

Ed, You may want to talk to these guys, they have have taken over the repair business from Mack Boring who is the largest yanmar in the east. These guys are in new jersey near long beach so you could drive the block down to speed repair. Richard – east coast boat transmission – 732-991-0694

Re: Stus-List solar vent wiggles, doesn't rotate

I put one in my head this spring and it was perfect, just the correct depth to come to the inside ceiling on my 40 George C&C40 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jerome Tauber via CnC-List Sent: Tuesday, July 14, 2015 4:56 PM To: cnc-list@cnc-list.com Cc: Je

Re: Stus-List Wet / Dry Vac recommendations?

Go to Home depot, they have a homer that fits on the top of a standard plastic bucket (you just but the power head part) , cheap, moderately powerful, use any bucket you normally have on the boat, good size - fits lots of places George C&C 40 From: CnC-List [mailto:cnc-list-boun...@cnc

Re: Stus-List bird spikes

You might want to try bird-x out of Chicago, they have a nylon version George C& C- 40 -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of John Pennie via CnC-List Sent: Sunday, November 30, 2014 10:56 AM To: Joe Della Barba; cnc-list@cnc-list.com Subjec

Re: Stus-List ; Oil and Water Temp gauge sending units;

The measurements you are giving for the sender are SAE- not metric, you will have to setup and converter anyway George C & C 40 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Richard N. Bush via CnC-List Sent: Monday, December 01, 2014 4:59 PM To: cnc-list@cnc-list.com Sub

Re: Stus-List Off C&C, but boating related question

I agree, the learning curve on auto cad type products is painful sometimes, I use a product - Turbo-Cad that is normally priced around $40- $80, depending on sales, it will do most anything, and save in most any format. The thought to use a student is quite good, George Cone C&C 40 Fr

Re: Stus-List A VERY tough decision

I purchased a C & C 40 that had spent 7 years on the dry. This was 4 years ago. Surprisingly few item were bad, and in fact I still use 2 of the batteries and they seem to be quite good—who knows? Yes I drained the fuel out and replaced, but everything works. I am on Lake Champlain, 2 hours fr

Re: Stus-List Looking for used RF Headsail of 34

I have an old #2 that was cut to work as a roller furling genny on your boat – C&C 40, it is in fair – to good shape, you probably have it at no cost to get you through this year and maybe more. It is for my 40. Thanks, George Cone From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behal

Re: Stus-List Yanmar 3GMD replacement on C&C 34

What is the cost if I can ask for just the motor Thanks George cone c&c 40 Unsinkable 2 Sent from my Verizon, Samsung Galaxy smartphone Original message From: Jack Fitzgerald via CnC-List Date: 9/17/17 11:55 AM (GMT-05:00) To: C&CList Cc: Jack Fitzgerald Subject: Re: Stus-

Re: Stus-List Prop pitch

I do have a spare 2 blade fixed that was on my C&C 40 that you can try, I suspect it will be a lot closer than what you are using now, and I am in the Shelburne shipyard to get it, my shaft is 1 1/8” the replacement prop is 16 x 11, my 3 hm27 will rev to 3000. George From: CnC-List [mailto

Re: Stus-List Old style ass NC is a luminum frame portlight gasket

Try uploading r video vfg The link Get Outlook for Android From: CnC-List on behalf of Dennis C. via CnC-List Sent: Friday, March 23, 2018 7:33:13 AM To: CnClist Cc: Dennis C. Subject: Re: Stus-List Old style aluminum frame portlight gaske

Re: Stus-List Pelican hook

The company that hS them is out of Hartford, i have it in my file from last year, when mine fell of, home tomorrow 81 c & c 40 George Sent from my Samsung Galaxy smartphone. Original message From: David Morrison via CnC-List Date: 8/13/18 2:19 PM (GMT-05:00) To: cnc-list@cn

Re: Stus-List Pelican hook

Here's the name and address for your parts Hayn Enterprises, LLC 51 Inwood Road Rocky Hill, CT 06067 USA Telephone 800.346.4296 860.257.0680 Fax George Cone 81 c & c 40 From: CnC-List On Behalf Of George Cone via CnC-List Sent: Monday, August 13, 2018 3:10 PM To: cnc-list@cnc-li

Re: Stus-List C&c40 -2 std rig main sail

I havee soft main, still fair, but good headsails if you need those from my 81 40-2 George Cone Sent from my Samsung Galaxy smartphone. Original message From: PETER OCAMPO via CnC-List Date: 9/25/18 12:58 PM (GMT-05:00) To: cnc-list@cnc-list.com Cc: PETER OCAMPO Subject: S

Re: Stus-List C&c40 -2 std rig main sail

I havee soft main, still fair, but good headsails if you need those from my 81 40-2 George Cone Sent from my Samsung Galaxy smartphone. Original message From: PETER OCAMPO via CnC-List Date: 9/25/18 12:58 PM (GMT-05:00) To: cnc-list@cnc-list.com Cc: PETER OCAMPO Subject: S

Re: Stus-List Folding & Feathering Prop Recommendations

I have a flex fold on my 40, they might have over propped me also . I can only go to 3000 rpm, but it is a two blade, no vibration. I'm happy with it. George cone C & C 40 Get Outlook for Android From: CnC-List on behalf of Bruce Whitmor

Re: Stus-List 2020 Rendezvous (s)

Tell us when and where, we’ll buy the air tickets now!! George Cone From: CnC-List On Behalf Of detroito91 via CnC-List Sent: Friday, November 1, 2019 5:05 PM To: cnc-list@cnc-list.com Cc: detroito91 Subject: Re: Stus-List 2020 Rendezvous (s) Great idea. Let's go there instead Jim Schwartz

Re: Stus-List D Sub Crimping...

A DB-9 has 9 pins as a detail. They Come in a variety of pin styles – solder, crimp, etc. if you want a couple of the crimp style – no soldering, I can send some down. Remember there is a male and female version, I can send a couple of each if you need George Cone 1981 C&C 40 Killington, VT

Re: Stus-List C&C 35 Mark III

I thought over the years the accepted recommendation was to put it into Reverse? George Cone 1981 C&C 40 From: CnC-List On Behalf Of Marek Dziedzic via CnC-List Sent: Wednesday, June 17, 2020 2:42 PM To: cnc-list@cnc-list.com Cc: Marek Dziedzic Subject: Re: Stus-List C&C 35 Mark III Most (as

Stus-List icebox drain

I have an 1981 C & C 40. I have never been able to find the output of the drain line on the icebox. Where does it come out from the floorboards where I can find it- under the sink area? It seems to travel that way from the icebox? Is there any valve on it? Thanks, George Cone Burlington, VT !9

Re: Stus-List [EXTERNAL] Free 35'

My son is interested and definitely capable, he sails our 40 fine, what are the details? We can get to marina there in Newark area. Easy enough, and then he would move it up to Boston where he lives. Thanks, George Cone From: CnC-List On Behalf Of Della Barba, Joe via CnC-List Sent: Wednesd

Re: Stus-List Free 35'

He never responded, i assume fraud Get Outlook for Android From: CnC-List on behalf of Joe Della Barba via CnC-List Sent: Thursday, May 2, 2019 3:36:19 PM To: cnc-list@cnc-list.com Cc: Joe Della Barba Subject: Re: Stus-List Free 35' Did

Re: Stus-List Anyone have a prop?

I have a fixed 16 x 9 two blade that came off my 81 – 40, it does have a 1 1/8th taper I believe, Will that help? Thanks, George 1981 C&C 40 Burlington, VT From: CnC-List On Behalf Of schiller via CnC-List Sent: Tuesday, May 28, 2019 7:46 AM To: cnc-list@cnc-list.com Cc: schiller Subject: Re:

Re: Stus-List Sailboat surveyor in Salem MA area

I can highly recommend Tom Ferguson, I don't know where he is now but here is his old address and email Thomas J. Ferguson 677 Lake Avenue Manchester, NH 03103 Try - 603-669-0734 TOM FERGUSON t...@prodigy.net George Cone C&C 40 Killington VT From: CnC-List On Beh

Stus-List Re: Boric Acid Powder

To update you on the dryer sheets, around here people use them to stop mice moving in to their boats and all, well I was just in working on a snowmobile groomer and it was full of dryer sheets, and as I lifted the console to check on some wiring there was a family of 6 mice nestled in the dryer

Stus-List Re: Eva faux decking

I put some very inexpensive eva on my cockpit for a test, planning to replace it with expensive material if it worked. I had two goals, one the admiral wanted something softer to sit on, and two my lab was always sliding around and uncomfortable when to boatwould lean. I was concerned the dog wo

Stus-List Re: Eva faux decking

20-1462 502-584-7255 -----Original Message- From: George Cone via CnC-List To: Stus-List Cc: Rod Stright ; George Cone Sent: Mon, Sep 20, 2021 9:10 am Subject: Stus-List Re: Eva faux decking I put some very inexpensive eva on my cockpit for a test, planning to replace it with expensive ma

Stus-List Re: Eva faux decking

wrote: George, can you define what is considered "inexpensive"? Also, any photos? Thanks! Richard s/v Bushmark4: 1985 C&C 37 CB: Ohio River, Mile 584; Richard N. Bush Law Offices 2950 Breckenridge Lane, Suite Nine Louisville, Kentucky 40220-1462 502-584-7255 -Origina

Stus-List cnc list

Stu, sorry to heap more on your desk, but I am not sure what is happening but I have been receiving the email list for 5 or 6 years, it is tremendous, all of a sudden it has not been coming in, since Christmas or before, what can I do to get re - linked up with it. I use Microsoft office 365 i

Stus-List Re: Cutting board orders

Yes, I ordered one on Monday, 4/18, if you need the order resent, just ask, paypal payment was completed Thanks, George Cone -Original Message- From: Stu via CnC-List Sent: Tuesday, April 19, 2022 9:05 AM To: C&C Email List Cc: Stu Subject: Stus-List Cutting board orders If you or

Stus-List Re: Marina/boatyard fires

As an amateur electrician (boy, that should scare you), I don't understand why the failure of the neutral will cause a fire? Yes all 110 taps will be dead- correct?, and it is possible the 220 feeds will vary in voltage, but why a fire opportunity? George Cone C&C 40 Burlington, VT From: Joe D

Stus-List Re: [EXTERNAL] Re: Marina/boatyard fires

I guess I'll go back to being an amateur electrician! George Cone C&C40 BTV, VT From: Della Barba, Joe via CnC-List Sent: Tuesday, November 29, 2022 9:29 AM To: Stus-List Cc: Della Barba, Joe Subject: Stus-List Re: [EXTERNAL] Re: Marina/boatyard fires The missing neutral back on shore causes

Stus-List Re: Hull painting

One detail, I have / had a 1981 c &c 40 white, I had a quart of special paint made to do some patching. Unfortunately the boat was hit by lightning before the 4th of July so I have no further need for the paint, $20.00 and it is yours! The boat was totaled due to hull penetrations Thanks, Geor

Stus-List Re: Hull painting

Sent: Tuesday, August 22, 2023 2:09 PM To: Stus-List Cc: Bill Coleman Subject: Stus-List Re: Hull painting What kind of paint? Bill Coleman Erie PA On Tue, Aug 22, 2023 at 1:34 PM George Cone via CnC-List mailto:cnc-list@cnc-list.com>> wrote: One detail, I have / had a 1981 c &c 40 whit

Stus-List Re: Hull painting

04 PM, George Cone via CnC-List mailto:cnc-list@cnc-list.com>> wrote: I’m wrong again, it is custom gelcoat, made by Fibre Glast Developments Corp – we used their color chart to get the color I’ll forward a photo of the can later. I have all sorts of sheet, spinnaker sheets , sails

Re: Stus-List New-guy C&C 40 Shopping questions

Jeff, I have one of the deep keel 40s and keep in mind it needs 8.40 feet of water not 7. Also. Don't minimize the wet decks. That can add up quick. As for sailing the 40 is fine but it really is a one cabin boat unless you know the others very well. I sail it up in lake champlain where the wa

Re: Stus-List New-guy C&C 40 Shopping questions

Jeff On Mon, Jul 20, 2020 at 11:43 PM George Cone via CnC-List mailto:cnc-list@cnc-list.com>> wrote: Jeff, I have one of the deep keel 40s and keep in mind it needs 8.40 feet of water not 7. Also. Don't minimize the wet decks. That can add up quick. As for sailing the 40 is fine but i

Stus-List Re: Winch bit

I do have the bit that fits into my 28 volt Milwaukee. I have 2 batteries and it raises the main or large people up the mast with ease . I get 4 or more raises out of a battery without recharges. George Cone C&C 40 Sent from my Verizon, Samsung Galaxy smartphone Get Outlook for Android

Stus-List Re: Seadeck / Raptor deck eva foam for cockpit

Bruno, I offer this as a thought, I purchased some of this material as a test, planning to remove it and buy the real expensive stuff, because I was concerned how it would hold up under the stress of my dog. An active retriever. I was amazed how good it has worked and in-fact bought some more

Stus-List C&C 40 PARTS

I have many good parts at a great price for sale from a 40 1 ½ oz spinnaker ¾ oz spinnaker Spinnaker pole and strut Whisker pole #1 light mylar headsail - very good condition #3 heavy Storm trysail Storm Headsail Many lines and sheets Variety of blocks Contact me for details George Cone 802-236