gers stuck together with it for sure!!
Charlie Nelson
-Original Message-
From: Bill Coleman via CnC-List
To: cnc-list@cnc-list.com
Cc: Bill Coleman
Sent: Thu, Jun 25, 2020 10:10 am
Subject: Re: Stus-List hatch repair / Now primer solution!
#yiv5817389147 #yiv5817389147 -- _filtered {}
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Lee
Youngblood via CnC-List
Sent: Wednesday, June 24, 2020 10:32 PM
To: CnC-List
Cc: Lee Youngblood
Subject: Re: Stus-List hatch repair / Now primer solution!
Hum, I thought this was solved years ago! Get the Krylon black
Cc: Lee Youngblood
Subject: [EXTERNAL] Re: Stus-List hatch repair / Now primer solution!
Hum, I thought this was solved years ago! Get the Krylon black plastic paint -
$4 or 5 bucks for the spray can and do a couple passes around the window.
You really should go to a C&C RDV, especially
I glued in a new jefa bearing into a perfectly prepped grp hull, PYI the
local dealer, recommended sika291.
Got a lift on the boat, set the rudder underneath, put it back on the
stands.
Jack up that rudder and without even getting fully into the bearing, the
whole bearing assembly slid up and int
> CnC-List
> Sent: Wednesday, June 24, 2020 1:31 PM
> To: cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com>
> Cc: Doug Mountjoy
> Subject: Re: Stus-List hatch repair
>
> I haven't used primer. I did the aft cabin hatch 3 years ago, and no leaks. I
> had the
purple primer.
Bill Coleman
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Doug
Mountjoy via CnC-List
Sent: Wednesday, June 24, 2020 1:31 PM
To: cnc-list@cnc-list.com
Cc: Doug Mountjoy
Subject: Re: Stus-List hatch repair
I haven't used primer. I did the aft cabin ha
I haven't used primer. I did the aft cabin hatch 3 years ago, and no leaks.
I had the some primer for the saloon and v-berth hatches, didn't notice it
was the wrong stuff until it was too late.
On Wed, Jun 24, 2020 at 9:56 AM dwight veinot via CnC-List <
cnc-list@cnc-list.com> wrote:
> I hope you
I hope you used the primer for the Sikaflex. First time I did not and the
thing leaked inside of 2 years. Cleaned it up all over agsin and used
primer second time. Still good after 5 years no leaks. The primer made the
difference
On Wed, Jun 24, 2020 at 12:54 PM Doug Mountjoy via CnC-List <
cnc-li
I did the hatch in place. Just sat on the deck with my legs hanging into
the cabin.
On Wed, Jun 24, 2020 at 9:16 AM Joe Della Barba via CnC-List <
cnc-list@cnc-list.com> wrote:
> How did you get the hinge pins out??
>
>
> Joe
> On 6/24/2020 11:54 AM, Doug Mountjoy via CnC-List wrote:
>
> Hi Joe,
Joe,
Not sure what model hatch you have but on my Bomar hatch they are slotted
spring pins like these https://www.mcmaster.com/catalog/126/3537
You can just push them out with a punch that is slightly smaller in
diameter than the pin (use a hammer and gently tap on it. When putting it
back togeth
How did you get the hinge pins out??
Joe
On 6/24/2020 11:54 AM, Doug Mountjoy via CnC-List wrote:
Hi Joe,
I just replaced the plexiglass on 2 of my hatches. I dug out most of
the sealant around the lens, then took a windshield removal tool to
cut the bond between the frame and lens. I used a
Hi Joe,
I just replaced the plexiglass on 2 of my hatches. I dug out most of the
sealant around the lens, then took a windshield removal tool to cut the
bond between the frame and lens. I used a wire wheel to clean up the
remainder of sealant. Wiped the frame with lacquer thinner, put a small
bevel
I have been asking about sending my hatches in for refurbishment and it isn't
cheap. Am I overthinking it? I only need two things, one is putting a new
gasket in and the other is a new piece of Plexiglas. I can buy the gasket and
the glue and the local shop can duplicate the glass easy enough. T
Check they are not bomars ... Our 85 was, replaced Them with Lewmar ocean
series that fit the opening better. Pompanette have parts for Bomars.
Paul. :)
On Feb 24, 2015, at 6:58 PM, Robert H. via CnC-List
mailto:cnc-list@cnc-list.com>> wrote:
I think my 1989 30 MKII has got Lewmar Superhatche
I have to be frugal I'm Irish. HAHAHA, no but really, I think I can take
mine and un-pin them and take the lense out and have a lense made and
re-bed it into the frame my self. the lower frame in not the culprit of my
leak. So I think if I can just find the right gasket I will win this
battle. I wo
I think my 1989 30 MKII has got Lewmar Superhatches (though I’m not even sure
about that).
What is the easiest (not necessarily cheapest) way to repair crazed lenses? I’m
not really keen on removing the hatch lids and shipping them off for repair. Is
there a complete lid replacement available
Hammerhead is a great outfit. Much cheaper than hatchsystems. The Atkins and
Doyle folks, while very nice, are useless: they want to sell you a new hatch.
I replaced the acrylic lens, gasket, one exterior knob and the handle washers
on my only hatch last fall and it's leakproof so far. Emai
17 matches
Mail list logo
