I've used Sta Lube boat trailer wheel bearing grease for assembly.
On Mar 9, 2019, at 5:34 PM, "Chuck McCown" wrote:
> When I was a kid, my grandfather had a container of axel grease. Like grease
> the hubs/axels of a horse drawn vehicle axel grease. It was sticky nasty
> black stuff. The o
I still have maybe an ounce of it left after around 30 years. The toothpick
I left in the container is very well lubed now.
--
bp
part15sbs{at}gmail{dot}com
On Sat, Mar 9, 2019 at 6:22 PM Bill Prince wrote:
>
> You got me curious so I went out to the garage to check it. It's Bel-Ray
> waterpro
You got me curious so I went out to the garage to check it. It's Bel-Ray
waterproof grease. Very thick stuff. It would most definitely hold bearings
in place for assembly.
https://www.amazon.com/Bel-Ray-FBA_99540-TB16W-Waterproof-Grease/dp/B0045L75M6?SubscriptionId=AKIAILSHYYTFIVPWUY6Q&tag=duckduc
That sounds like maybe marine grease.
Chuck, could you use wheel bearing grease, or maybe assembly grease?
From: AF On Behalf Of Bill Prince
Sent: Saturday, March 9, 2019 7:53 PM
To: AnimalFarm Microwave Users Group
Subject: Re: [AFMUG] OT Axel Grease
There is some stuff that I
Kind of like this stuff:
https://www.amazon.com/Sta-Lube-SL3121-Trailer-Bearing-Fluid_Ounces/dp/B000CPJMY8?psc=1&SubscriptionId=AKIAILSHYYTFIVPWUY6Q&tag=duckduckgo-d-20&linkCode=xm2&camp=2025&creative=165953&creativeASIN=B000CPJMY8
--
bp
part15sbs{at}gmail{dot}com
On Sat, Mar 9, 2019 at 5:53 PM
And isn't Axel a person's name? I thought the thing a tire rotates on is an
axle.
Don't pay attention to me. Get off my lawn!
--
bp
part15sbs{at}gmail{dot}com
On Sat, Mar 9, 2019 at 5:52 PM Bill Prince wrote:
>
> There is some stuff that I have from back in motorcycle days. I don't
> remember
There is some stuff that I have from back in motorcycle days. I don't
remember where I got it, but it said "salt water resistant" on the package.
I still use it (the little container lasts a long, long, LONG time). I use
it to lube the PTO shaft on the tractor and mower. Also use it on the hitch
pi
When I was a kid, my grandfather had a container of axel grease. Like grease
the hubs/axels of a horse drawn vehicle axel grease. It was sticky nasty black
stuff. The only use I knew about was he would grease the ball hitch on his car
prior to pulling his camp trailer.
Tomorrow I start the
I brought it into the office and ran some measured pieces through.
It has a meters/second setting and they were doing some mental math to come up
with the higher number.
And they did not blow as far as I thought that run was.
It was doing 350 fpm, but still that is really hauling a$$
From: c
Yeah, too steep for me. I use AutoCadLT subscription model
Most developers will give us cad files of the power design. We hopefully can
get in the same ditch and just use their drawing.
If you want to integrate drawings, then there is the whole landbase issue that
I have not yet solved.
Like
Vetro Fibermap looks pretty nice, the price is a bit steep though IMO. I've
been using Google Earth.
On Saturday, March 9, 2019, Chris Fabien wrote:
> We do essentially the same using MapInfo Professional. I'm not sure it's
> the best software but it gets the job done.
>
> Some permit agencies
We do essentially the same using MapInfo Professional. I'm not sure it's
the best software but it gets the job done.
Some permit agencies require using a locatable method to cross the road.
Meaning yes you need a drill and cant use a missile or compaction boring
setup. Worth asking though.
On Sa
736 Remington is not far from where we lived in Sunnyvale (we had a
residence in Sunnyvale from 1980-1996 before we moved into the mountains).
--
bp
part15sbs{at}gmail{dot}com
On Sat, Mar 9, 2019 at 7:38 AM Robert wrote:
> 736 Remington Drive 1962-1969... Lockheed was the big employer.
> Doc
736 Remington Drive 1962-1969... Lockheed was the big employer.
Doctors were the top of the income pyramid.. Cherry orchards
everywhere.. A different world in Sunnyvale back then...
On 3/9/19 7:10 AM, Bill Prince wrote:
Yes. It was pure luck. My first "real" job, and I was destined for a
Yes. In your PPPoE profile, you'd specify a v6 Prefix Pool for both
the "Remote IPv6 Prefix Pool" and the "DHCPv6 PD Pool" (it can be
from the same pool, it will assign them two prefixes from that
pool). The former is for the WAN port of the customer's device and
the latt
Agreed. Usually shapefiles come with a .PRJ file that defines the coordinate
system. I would think something created in a GIS system in the first place
would be more likely to have that file passed along than one created in a CAD
environment and then exported.
-
Mike Hammett
Intellige
It's a single lane, mountain road, and I don't travel according to the
commute direction.
--
bp
part15sbs{at}gmail{dot}com
On Fri, Mar 8, 2019 at 5:20 PM Ken Hohhof wrote:
> Why are all the Teslas going the opposite direction?
>
>
>
> *From:* AF *On Behalf Of *Chuck McCown
> *Sent:* Friday, M
Yes. It was pure luck. My first "real" job, and I was destined for a field
job in Gary, Indiana. Two weeks after that, Sperry bought our company and
laid off 5 out of 6 of the employees. I figure they kept me because I was
cheap (fresh out of college). Of the remaining 1 out of 6, half quit and
wal
You have to be very careful with your coordinate reference system. There are
(literally) thousands of them. One advantage of using the county GIS data and
aerials is that the aerials are (usually) corrected and in the same CRS as the
SHP files.
Mark
> On Mar 9, 2019, at 9:51 AM, Mike H
I use ArcGIS with a center line layer from the Census Bureau and a parcels
layer from the county.
-
Mike Hammett
Intelligent Computing Solutions
Midwest Internet Exchange
The Brothers WISP
- Original Message -
From: "TJ Trout"
To: "AnimalFarm Microwave Users Group"
One of the best threads evar
glad it's 'free' to lurk.
--
On Thu, Mar 7, 2019 at 7:17 PM Ken Hohhof wrote:
> Kudos to Forrest, he zeroed right in on the problem.
>
> I had blinders on, and focused on the control circuitry instead of the
> regulators.
>
>
>
> Plus you were in a great position to
I use autocad with a google earth image underneath. You can missile if the
soil is good.
Sent from my iPhone
> On Mar 9, 2019, at 12:30 AM, TJ Trout wrote:
>
> how are most of you guys getting your design on paper for pulling permits?
> I'm assuming if I design a plant layout on a napkin I n
22 matches
Mail list logo
