Package: installation-reports
Severity: normal
Tags: d-i
X-Debbugs-Cc: atzli...@sina.com
Boot method: USB
Image version:
https://mirrors.bfsu.edu.cn/debian-cd/11.2.0/arm64/iso-dvd/debian-11.2.0-arm64-DVD-1.iso
Date: 2020-01-22
Machine: Phytium CPU FT-2000/4
Partitions:
udev devtmpfs 80952840 80952840% /dev
tmpfs tmpfs 1629332 1080 16282521% /run
/dev/nvme0n1p8 ext4 57358176 15467140 38944988 29% /
tmpfs tmpfs 81466520 81466520% /dev/shm
tmpfs tmpfs 51204 51161% /run/lock
/dev/nvme0n1p7 ext4 123268672 8663604 1082972288% /data
/dev/nvme0n1p1 vfat523248164045068444% /boot/efi
tmpfs tmpfs 16293280 16293280% /run/user/0
tmpfs tmpfs 16293280 16293280% /run/user/1000
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card:[E]
Configure network: [E]
Detect media: [O]
Load installer modules: [O]
Clock/timezone setup: [O]
User/password setup:[O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system:[O]
Install tasks: [O]
Install boot loader:[O]
Overall install:[O]
Comments/Problems:
The hardware info can also find in:
https://linux-hardware.org/?probe=d0ecbeff52
The box has one NIC,it can't been find in the install.
The NIC type is Atheros 8035 ethernet.
This NIC is integrated in board, use phy.
This NIC can drived by the other distribution base on Debian, like UOS
or Kylin.
kernel is:
4.19.0-arm64-desktop #4310 SMP Tue Dec 28 22:31:27 CST 2021 aarch64 GNU/Linux
The dmesg output is:
[ 0.955906] libphy: Fixed MDIO Bus: probed
[ 0.959396] ---acpi:stmmac irq is 9 9 -1
[ 0.959405] --stmmac_probe_config_acpi: plat interface is a
[ 0.959407] ---plat bus_id is 0
[ 0.959408] stammac acpi phy setup -
[ 0.959411] stmmac_probe_config_acpi:tx-fifo-depth 1, rx-fifo-depth
1
[ 0.959413] Unicast table entries set to unexpected value 65
[ 0.959414] ---GMAC pbl is 10
[ 0.959419] stmmaceth clock freq is 25000
[ 0.959422] get stmmac clk:(ptrval)
[ 0.959423] register stmmac_clk PHYT0004:00
[ 0.959430] set stmmac_clk:PHYT0004:00
[ 0.959434] PTP use main clock
[ 0.959436] stmmaceth PHYT0004:00: no reset control found
[ 0.959475] stmmaceth PHYT0004:00: User ID: 0x10, Synopsys ID: 0x36
[ 0.959478] stmmaceth PHYT0004:00: DWMAC1000
[ 0.959480] stmmaceth PHYT0004:00: DMA HW capability register supported
[ 0.959482] stmmaceth PHYT0004:00: RX Checksum Offload Engine supported
[ 0.959483] stmmaceth PHYT0004:00: COE Type 2
[ 0.959485] stmmaceth PHYT0004:00: TX Checksum insertion supported
[ 0.959487] stmmaceth PHYT0004:00: Normal descriptors
[ 0.959488] stmmaceth PHYT0004:00: Ring mode enabled
[ 0.959490] stmmaceth PHYT0004:00: Enable RX Mitigation via HW Watchdog
Timer
[ 0.968837] libphy: stmmac: probed
[ 0.968841] Atheros 8035 ethernet stmmac-0:04: attached PHY driver [Atheros
8035 ethernet] (mii_bus:phy_addr=stmmac-0:04, irq=POLL)
[ 0.968987] ---acpi:stmmac irq is 10 10 -1
[ 0.968997] --stmmac_probe_config_acpi: plat interface is a
[ 0.968999] ---plat bus_id is 1
[ 0.969000] stammac acpi phy setup -
[ 0.969002] stmmac_probe_config_acpi:tx-fifo-depth 1, rx-fifo-depth
1
[ 0.969003] Unicast table entries set to unexpected value 65
[ 0.969005] ---GMAC pbl is 10
[ 0.969008] stmmaceth clock freq is 25000
[ 0.969010] get stmmac clk:(ptrval)
[ 0.969011] register stmmac_clk PHYT0004:01
[ 0.969013] set stmmac_clk:PHYT0004:01
[ 0.969015] PTP use main clock
[ 0.969017] stmmaceth PHYT0004:01: no reset control found
[ 0.969053] stmmaceth PHYT0004:01: User ID: 0x10, Synopsys ID: 0x36
[ 0.969055] stmmaceth PHYT0004:01: DWMAC1000
[ 0.969056] stmmaceth PHYT0004:01: DMA HW capability register supported
[ 0.969058] stmmaceth PHYT0004:01: RX Checksum Offload Engine supported
[ 0.969059] stmmaceth PHYT0004:01: COE Type 2
[ 0.969060] stmmaceth PHYT0004:01: TX Checksum insertion supported
[ 0.969062] stmmaceth PHYT0004:01: Normal descriptors
[ 0.969063] stmmaceth PHYT0004:01: Ring mode enabled
[ 0.969064] stmmaceth PHYT0004:01: Enable RX Mitigation via HW Watchdog
Timer
[ 0.975643] libphy: stmmac: probed
[ 0.975646] stmmaceth PHYT0004:01: No PHY found
[ 0.975666] stmmaceth PHYT0004:01: stmmac_dvr_probe: MDIO bus (id: 1)
registration failed
[ 2.606904] stmmaceth PHYT0004:00 enaphyt4i0: renamed from eth0
[ 8.402441] stmmaceth PHYT0004:00 enaphyt4i0: No Safety Features support
found
[ 8.402446] stmmaceth PHYT0004:00 enaphyt4i0: PTP not supported by HW
[ 8.402450] stmmaceth PHYT0004:00: dev_name:PHYT0004:00, port:0
[
