Hi Rolf,
now hopefully the right debug information. Now after starting scanimage -A
, it waits for the button information. I try different buttons (black,
color) Changed before from JPEG to PDF or TIFF but scanimage waits till
timeout. See the output.
regards Matthias
root at matze-Satellite-C660:/usr/local/src/sane-backends-git/sane-backends#
scanimage -V
scanimage (sane-backends) 1.0.24git; backend version 1.0.24
root at matze-Satellite-C660:/usr/local/src/sane-backends-git/sane-backends#
scanimage -A
[sanei_debug] Setting debug level of pixma to 7.
[pixma] pixma is compiled without pthread support.
[pixma] pixma version 0.17.0
[pixma] pixma_collect_devices() found Canon PIXMA MG6200 at libusb:002:005
[pixma] sanei_bjnp_find_devices:
[pixma] eth0 is IPv4 capable, sending broadcast, socket = 3
[pixma] wlan0 is IPv4 capable, sending broadcast, socket = 4
[pixma] eth0 is IPv6 capable, sending broadcast, socket = 5
[pixma] wlan0 is IPv6 capable, sending broadcast, socket = 6
[pixma] pixma_find_scanners() found 1 devices
[pixma] pixma_collect_devices() found Canon PIXMA MG6200 at libusb:002:005
[pixma] sanei_bjnp_find_devices:
[pixma] eth0 is IPv4 capable, sending broadcast, socket = 3
[pixma] wlan0 is IPv4 capable, sending broadcast, socket = 4
[pixma] eth0 is IPv6 capable, sending broadcast, socket = 5
[pixma] wlan0 is IPv6 capable, sending broadcast, socket = 6
[pixma] pixma_open(): Canon PIXMA MG6200
All options specific to device `pixma:04A91755_14B4F6':
Scan mode:
--resolution auto||75|150|300|600|1200|2400|4800dpi [75]
Sets the resolution of the scanned image.
--mode auto|Color|Gray|Lineart [Color]
Selects the scan mode (e.g., lineart, monochrome, or color).
--source Flatbed [Flatbed]
Selects the scan source (such as a document-feeder). Set source
before
mode and resolution. Resets mode and resolution to auto values.
--button-controlled[=(yes|no)] [no]
When enabled, scan process will not start immediately. To proceed,
press "SCAN" button (for MP150) or "COLOR" button (for other
models).
To cancel, press "GRAY" button.
Gamma:
--custom-gamma[=(auto|yes|no)] [yes]
Determines whether a builtin or a custom gamma-table should be used.
--gamma-table auto|0..255,...
Gamma-correction table. In color mode this option equally affects
the
red, green, and blue channels simultaneously (i.e., it is an
intensity
gamma table).
--gamma auto|0.299988..5 [2.2]
Changes intensity of midtones
Geometry:
-l auto|0..216.069mm [0]
Top-left x position of scan area.
-t auto|0..297.011mm [0]
Top-left y position of scan area.
-x auto|0..216.069mm [216.069]
Width of scan-area.
-y auto|0..297.011mm [297.011]
Height of scan-area.
Buttons:
--button-update
Update button state
[pixma] Sending time: '13/02/05 18:12'
[pixma] No response yet. Timed out in 8 sec.
[pixma] No response yet. Timed out in 7 sec.
[pixma] No response yet. Timed out in 6 sec.
[pixma] No response yet. Timed out in 5 sec.
[pixma] No response yet. Timed out in 4 sec.
[pixma] No response yet. Timed out in 3 sec.
[pixma] No response yet. Timed out in 2 sec.
[pixma] No response yet. Timed out in 1 sec.
[pixma] WARNING: Error in response phase. cmd:eb80
[pixma] If the scanner hangs, reset it and/or unplug the USB cable.
--button-1 <int> [0] [read-only]
Button 1
--button-2 <int> [0] [read-only]
Button 2
--original <int> [0] [read-only]
Type of original to scan
--target <int> [0] [read-only]
Target operation type
Extras:
--threshold auto|0..100% (in steps of 1) [inactive]
Select minimum-brightness to get a white point
--threshold-curve auto|0..127 (in steps of 1) [inactive]
Dynamic threshold curve, from light to dark, normally 50-65
[pixma] pixma_close(): Canon PIXMA MG6200
root at matze-Satellite-C660:/usr/local/src/sane-backends-git/sane-backends#
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.alioth.debian.org/pipermail/sane-devel/attachments/20130205/b5394710/attachment-0001.html>
