What is the output of scanimage -A allan
On Tue, Dec 4, 2012 at 6:27 PM, Rien Broekstra <rien at rename-it.nl> wrote: > Hello everyone, > > I was directed to this list from the sane irc channel. My apologies if this > message is off topic: > > I'm not getting scanbd 1.2.1 to work with a canon dr-2010c scanner, > connected to an alix 6f2 board running debian squeeze. Here's what I have > done so far: > > I built scanbd (on a different machine) according to the INSTALL file with > $ USE_SANE=yes make -e clean all > > I copied the resulting binary to the target system in /usr/sbin and the > configuration file to /etc/scanbd; > > ...copied scanbd_dbus.conf to /etc/dbus-1/system.d/ and restarted dbus > > ...installed the libconfuse0, libusb-0.1-4, libusb-1.0-0, libsane and > libudev0 packages (not the -dev packages, since there is no space on the > target system for the compiler that is installed as a dependency); > > ...copied canon_dr.conf, saned.conf and dll.conf from the sane configuration > directory to /etc/scanbd. Added a netmask to /etc/scanbd/saned.conf and > commented out the net backend in /etc/scanbd/dll.conf, and checked that the > canon_dr backend was not commented out. > > Modified scanbd.conf to set SANE_CONFIG_DIR to /etc/scanbd (instead of > /usr/local/etc/scanbd) > > The scanner is recognized by the kernel and by sane: > > --------------8<------------------ > dmesg: > [ 630.948077] usb 1-3: new high speed USB device using ehci_hcd and address > 5 > [ 631.089822] usb 1-3: New USB device found, idVendor=1083, idProduct=161b > [ 631.096584] usb 1-3: New USB device strings: Mfr=1, Product=2, > SerialNumber=0 > [ 631.103808] usb 1-3: Product: CANON DR-2010C > [ 631.109015] usb 1-3: Manufacturer: CANON > > root at vpnbox-f2-emmastr:/etc/scanbd# scanimage -L > device `canon_dr:libusb:001:005' is a CANON DR-2010C scanner > --------------8<------------------ > > However, scanbd won't find the scanner: > > --------------8<------------------ > root at vpnbox-f2-emmastr:/etc/dbus-1/system.d# /usr/sbin/scanbd -df -c > /etc/scanbd/scanbd.conf > /usr/sbin/scanbd: debug on: level: 7 > /usr/sbin/scanbd: dropping privs to uid saned > /usr/sbin/scanbd: dropping privs to gid lp > /usr/sbin/scanbd: drop privileges to gid: 7 > /usr/sbin/scanbd: Running as effective gid 7 > /usr/sbin/scanbd: drop privileges to uid: 111 > /usr/sbin/scanbd: Running as effective uid 111 > /usr/sbin/scanbd: dbus_init > /usr/sbin/scanbd: dbus match > type='signal',interface='org.freedesktop.Hal.Manager' > /usr/sbin/scanbd: sane version 1.0 > /usr/sbin/scanbd: Scanning for local-only devices > /usr/sbin/scanbd: start_sane_threads > /usr/sbin/scanbd: start dbus thread > /usr/sbin/scanbd: udev init > /usr/sbin/scanbd: get udev monitor > /usr/sbin/scanbd: start udev thread > /usr/sbin/scanbd: timeout: 500 ms > /usr/sbin/scanbd: Iteration on dbus call > /usr/sbin/scanbd: udev thread started > /usr/sbin/scanbd: Iteration on dbus call > /usr/sbin/scanbd: Iteration on dbus call > /usr/sbin/scanbd: Iteration on dbus call > ^C/usr/sbin/scanbd: sig_term/int_handler called with signal 2 > /usr/sbin/scanbd: stop_sane_threads > /usr/sbin/scanbd: stop dbus thread > /usr/sbin/scanbd: join dbus thread > /usr/sbin/scanbd: stop udev thread > /usr/sbin/scanbd: join udev thread > /usr/sbin/scanbd: cleanup device handler > /usr/sbin/scanbd: close udev monitor > /usr/sbin/scanbd: close udev > /usr/sbin/scanbd: exiting scanbd > --------------8<------------------ > > Any ideas what I might do next to make it find the scanner? > > Thanks in advance! > -- > Rien > > -- > sane-devel mailing list: sane-devel at lists.alioth.debian.org > http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/sane-devel > Unsubscribe: Send mail with subject "unsubscribe your_password" > to sane-devel-request at lists.alioth.debian.org -- "The truth is an offense, but not a sin"
