Hello, I'm trying to connect a Fujitsu fi-60f to a system running fedora 8. I got to the point (I think..) where all of the pieces are in the right place but I can't get it to work.
Any help would be appreciated. Here are the vitals: $ /sbin/lsusb Bus 001 Device 003: ID 04c5:10c7 Fujitsu, Ltd --------------------------------------------------------------- $ scanimage -V scanimage (sane-backends) 1.0.19; backend version 1.0.19 --------------------------------------------------------------- $ sane-find-scanner # sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter. found USB scanner (vendor=0x04c5, product=0x10c7) at libusb:001:003 # Your USB scanner was (probably) detected. It may or may not be supported by # SANE. Try scanimage -L and read the backend's manpage. ------------------------------------------------------------------- $ SANE_DEBUG_EPJITSU=15 scanimage -L 2>f60.log No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). $ cat f60.log [sanei_debug] Setting debug level of epjitsu to 15. [epjitsu] sane_init: start [epjitsu] sane_init: epjitsu backend 1.0.10, from sane-backends 1.0.19 [epjitsu] sane_init: reading config file epjitsu.conf [epjitsu] sane_init: firmware '/usr/local/share/sane/epjitsu/60f_0A06.nal' [epjitsu] sane_init: looking for 'usb 0x04c5 0x10c7' [epjitsu] attach_one: start 'libusb:001:003' [epjitsu] attach_one: init struct [epjitsu] attach_one: connect fd [epjitsu] connect_fd: start [epjitsu] connect_fd: opening USB device [epjitsu] connect_fd: could not open device: 11 [epjitsu] connect_fd: finish [epjitsu] sane_close: start [epjitsu] teardown_buffers: start [epjitsu] teardown_buffers: finish [epjitsu] sane_close: finish [epjitsu] sane_init: firmware '/usr/local/share/sane/epjitsu/300_0A00.nal' [epjitsu] sane_init: looking for 'usb 0x04c5 0x1156' [epjitsu] sane_init: found 0 scanner(s) [epjitsu] sane_init: finish [epjitsu] sane_get_devices: start [epjitsu] sane_get_devices: finish [epjitsu] sane_exit: start [epjitsu] sane_exit: finish ------------------------------------------------------------------- Now I gathered that status 11 is SANE_STATUS_ACCESS_DENIED so I tried the same command using sudo but got the same response and the log file was completely empty...:confused: $ SANE_DEBUG_EPJITSU=15 sudo scanimage -L 2>f60.log No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). $ cat f60.log $ Again, any help would be greatly appreciated. Ronen -- View this message in context: http://www.nabble.com/epjitsu-%28Fujitsu-fi-60f%29-on-fedora-8-tp20940308p20940308.html Sent from the SANE - Dev mailing list archive at Nabble.com.
