Here's the SANE_DEBUG_EPSON=255 scanimage -L [sanei_debug] Setting debug level of epson to 255. [epson] sane_init: sane-backends 1.0.18-cvs [epson] sane_init, ># epson.conf< [epson] sane_init, >#< [epson] sane_init, ># here are some examples for how to configure the EPSON backend< [epson] sane_init, >#< [epson] sane_init, ># SCSI scanner:< [epson] sane_init, >scsi EPSON< [epson] sane_init, ># for the GT-6500:< [epson] sane_init, >scsi "EPSON SC"< [epson] sane_init, >#< [epson] sane_init, ># Parallel port scanner:< [epson] sane_init, >#pio 0x278< [epson] sane_init, >#pio 0x378< [epson] sane_init, >#pio 0x3BC< [epson] sane_init, >#< [epson] sane_init, ># USB scanner:< [epson] sane_init, ># There are two different methods of configuring a USB scanner: libusb and the kernel module< [epson] sane_init, ># For any system with libusb support (which is pretty much any recent Linux distribution) the< [epson] sane_init, ># following line is sufficient. This however assumes that the connected scanner (or to be more< [epson] sane_init, ># accurate, it's device ID) is known to the backend.< [epson] sane_init, >usb< [epson] attach_one_usb() [epson] SANE Epson Backend v0.2.47 - 2006-08-21 [epson] attach(, 3) [epson] attach: opening [epson] attach_one_usb(libusb:005:002-04b8-011e-ff-ff) [epson] SANE Epson Backend v0.2.47 - 2006-08-21 [epson] attach(libusb:005:002-04b8-011e-ff-ff, 3) [epson] attach: opening libusb:005:002-04b8-011e-ff-ff [epson] sane_init, ># For libusb support for unknown scanners use the following command< [epson] sane_init, ># usb <product ID> <device ID>< [epson] sane_init, ># e.g.:< [epson] sane_init, >usb 0x4b8 0x11e< [epson] attach_one_usb(libusb:005:002-04b8-011e-ff-ff) [epson] SANE Epson Backend v0.2.47 - 2006-08-21 [epson] attach(libusb:005:002-04b8-011e-ff-ff, 3) [epson] attach: opening libusb:005:002-04b8-011e-ff-ff [epson] sane_init, ># And for the scanner module, use the following configuration:< [epson] sane_init, >#usb /dev/usbscanner0< [epson] sane_init, >#usb /dev/usb/scanner0< [epson] sane_get_devices()
No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). Rob. On 17/09/2007, Mattias Ellert <mattias.ellert at tsl.uu.se> wrote: > m?n 2007-09-17 klockan 13:12 +0100 skrev Rob Thomas: > > Hi, > > Here's the output as requested: > > [ ... ] > > > cheers, > > Rob. > > Add debugging output to the last call: > > SANE_DEBUG_EPSON=255 scanimage -L > > Mattias > > >
