I have previously sent in the output of: export SANE_DEBUG_PLUSTEK=19 ; scanimage -L
as advised by Gerhard Jaeger and want to add some observations. I am able to use the scanner on the same hardware, using a Slax Linux LiveCD and sane-backends-1.0.17 Back to OpenBSD, what I have also noticed, is that if I disconnect the scanner, then reconnect it, scanimage -L will show the scanner as being connected, but only for a limited length of time. It is not long enough to do anything useful though. If I disconnect it then reconnect it and try xscanimage, I will get the initial dialogue box and can select resolution and color depth, but when I attempt scan something, the scanner has become unavailable again and I get a pure black scan. I'm only able to get even this far, if I do all this as root, but that is obviously a permission issue and I can address that after I have got this working. Hope the above helps and I have again included the sane debug output below. -- Best regards, Craig http://slashboot.org/ Support OpenBSD http://www.openbsd.org/orders.html # export SANE_DEBUG_PLUSTEK=19 ; scanimage -L [sanei_debug] Setting debug level of plustek to 19. [plustek] Plustek backend V0.50-7, part of sane-backends 1.0.17 [plustek] Retrieving all supported and conntected devices [plustek] Checking for 0x07b3-0x0010 [plustek] Checking for 0x07b3-0x0011 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0015 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0013 [plustek] Checking for 0x07b3-0x0013 [plustek] Checking for 0x07b3-0x0011 [plustek] Checking for 0x07b3-0x0010 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0015 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0016 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0007 [plustek] Checking for 0x07b3-0x000f [plustek] Checking for 0x07b3-0x000f [plustek] Checking for 0x07b3-0x0005 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0012 [plustek] Checking for 0x0400-0x1000 [plustek] Checking for 0x0400-0x1001 [plustek] Checking for 0x0400-0x1001 [plustek] Checking for 0x0458-0x2007 [plustek] Checking for 0x0458-0x2008 [plustek] Checking for 0x0458-0x2009 [plustek] Checking for 0x0458-0x2013 [plustek] Checking for 0x0458-0x2015 [plustek] Checking for 0x0458-0x2016 [plustek] Checking for 0x03f0-0x0505 [plustek] Checking for 0x03f0-0x0605 [plustek] Checking for 0x04b8-0x010f [plustek] Checking for 0x04b8-0x011d [plustek] Checking for 0x1606-0x0050 [plustek] Checking for 0x1606-0x0060 [plustek] Checking for 0x1606-0x0160 [plustek] Checking for 0x049f-0x001a [plustek] Checking for 0x04a9-0x2206 [plustek] Checking for 0x04a9-0x2207 [plustek] Checking for 0x04a9-0x2208 [plustek] Checking for 0x04a9-0x220d [plustek] Checking for 0x04a9-0x220e [plustek] Checking for 0x04a9-0x2220 [plustek] Available and supported devices: [plustek] Device: >libusb:/dev/usb1:/dev/ugen0< - 0x04a9x0x220d [plustek] ># Plustek-SANE Backend configuration file< [plustek] ># For use with LM9831/2/3 based USB scanners< [plustek] >#< [plustek] >< [plustek] ># each device needs at least two lines:< [plustek] ># - [usb] vendor-ID and product-ID< [plustek] ># - device devicename< [plustek] ># i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)< [plustek] ># [usb] 0x07B3 0x0017< [plustek] ># device /dev/usbscanner< [plustek] ># or< [plustek] ># device libusb:bbb:ddd< [plustek] ># where bbb is the busnumber and ddd the device number< [plustek] ># make sure that your user has access to /proc/bus/usb/bbb/ddd< [plustek] >#< [plustek] ># additionally you can specify some options< [plustek] ># warmup, lOffOnEnd, lampOff< [plustek] >#< [plustek] ># For autodetection use< [plustek] ># [usb]< [plustek] ># device /dev/usbscanner< [plustek] >#< [plustek] ># or simply< [plustek] ># [usb]< [plustek] >#< [plustek] ># or if you want a specific device but you have no idea about the< [plustek] ># device node or you use libusb, simply set vendor- and product-ID< [plustek] ># [usb] 0x07B3 0x0017< [plustek] ># device auto< [plustek] >#< [plustek] ># NOTE: autodetection is safe, as it uses the info it got< [plustek] ># from the USB subsystem. If you're not using the< [plustek] ># autodetection, you MUST have attached that device< [plustek] ># at your USB-port, that you have specified...< [plustek] >#< [plustek] >< [plustek] >[usb]< [plustek] next device uses autodetection [plustek] ... next device [plustek] >#[usb] 0x04A9 0x220D< [plustek] >usb 0x04A9 0x220D< [plustek] ignoring >usb 0x04A9 0x220D< [plustek] >< [plustek] >#device /dev/uscanner< [plustek] >#device libusb:/dev/usb1:/dev/ugen0< [plustek] >device auto< [plustek] Decoding device name >auto< [plustek] >< [plustek] >#< [plustek] ># options for the previous USB entry< [plustek] >#< [plustek] ># switch lamp off after xxx secs, 0 disables the feature< [plustek] ># (can also be set via frontend)< [plustek] >option lampOff 300< [plustek] Decoding option >lampOff< [plustek] >< [plustek] ># warmup period in seconds, 0 means no warmup, -1 means auto-warmup< [plustek] ># (can also be set via frontend)< [plustek] >option warmup -1< [plustek] Decoding option >warmup< [plustek] >< [plustek] ># 0 means leave lamp-status untouched, not 0 means switch off< [plustek] ># on sane_close< [plustek] ># (can also be set via frontend)< [plustek] >option lOffOnEnd 1< [plustek] Decoding option >lOffOnEnd< [plustek] >< [plustek] >#< [plustek] ># options to tweak the image start-position< [plustek] ># (WARNING: there's no internal range check!!!)< [plustek] >#< [plustek] ># for the normal scan area< [plustek] >#< [plustek] >option posOffX 0< [plustek] Decoding option >posOffX< [plustek] >option posOffY 0< [plustek] Decoding option >posOffY< [plustek] >< [plustek] ># for transparencies< [plustek] >option tpaOffX 0< [plustek] Decoding option >tpaOffX< [plustek] >option tpaOffY 0< [plustek] Decoding option >tpaOffY< [plustek] >< [plustek] ># for negatives< [plustek] >option negOffX 0< [plustek] Decoding option >negOffX< [plustek] >option negOffY 0< [plustek] Decoding option >negOffY< [plustek] >< [plustek] >#< [plustek] ># for setting the calibration strip position< [plustek] ># (WARNING: there's no internal range check!!!)< [plustek] ># -1 means use built in< [plustek] ># (can also be set via frontend)< [plustek] >option posShadingY -1< [plustek] Decoding option >posShadingY< [plustek] >option tpaShadingY -1< [plustek] Decoding option >tpaShadingY< [plustek] >option negShadingY -1< [plustek] Decoding option >negShadingY< [plustek] >< [plustek] >#< [plustek] ># to invert the negatives, 0 disables the feature< [plustek] >#< [plustek] >option invertNegatives 0< [plustek] Decoding option >invertNegatives< [plustek] >< [plustek] >#< [plustek] ># to disable the internal sensor speedup function,< [plustek] ># 1 disables the feature< [plustek] >#< [plustek] >option disableSpeedup 0< [plustek] Decoding option >disableSpeedup< [plustek] >< [plustek] >#< [plustek] ># to save/restore coarse calibration data< [plustek] ># (can also be set via frontend)< [plustek] >option cacheCalData 0< [plustek] Decoding option >cacheCalData< [plustek] >< [plustek] >#< [plustek] ># use alternate calibration routines< [plustek] >#< [plustek] >option altCalibration 0< [plustek] Decoding option >altCalibration< [plustek] >< [plustek] >#< [plustek] ># for skipping whole calibration step< [plustek] >#< [plustek] >option skipCalibration 0< [plustek] Decoding option >skipCalibration< [plustek] >< [plustek] >#< [plustek] ># for skipping entire fine calibration step< [plustek] ># coarse calibration is done< [plustek] >#< [plustek] >option skipFine 0< [plustek] Decoding option >skipFine< [plustek] >< [plustek] >#< [plustek] ># discard the result of the fine white calibration< [plustek] >#< [plustek] >option skipFineWhite 0< [plustek] Decoding option >skipFineWhite< [plustek] >< [plustek] ># for replacing the gain values found during coarse< [plustek] ># calibration< [plustek] ># (can also be set via frontend)< [plustek] >option red_gain -1< [plustek] Decoding option >red_gain< [plustek] >option green_gain -1< [plustek] Decoding option >green_gain< [plustek] >option blue_gain -1< [plustek] Decoding option >blue_gain< [plustek] >< [plustek] ># for replacing the offset values found during coarse< [plustek] ># calibration< [plustek] ># (can also be set via frontend)< [plustek] >option red_offset -1< [plustek] Decoding option >red_offset< [plustek] >option green_offset -1< [plustek] Decoding option >green_offset< [plustek] >option blue_offset -1< [plustek] Decoding option >blue_offset< [plustek] >< [plustek] >#< [plustek] ># for replacing the default lampoff settings, this< [plustek] ># works only for CIS devices like CanoScan LiDE20< [plustek] ># (can also be set via frontend)< [plustek] >option red_lampoff -1< [plustek] Decoding option >red_lampoff< [plustek] >option green_lampoff -1< [plustek] Decoding option >green_lampoff< [plustek] >option blue_lampoff -1< [plustek] Decoding option >blue_lampoff< [plustek] >< [plustek] >#< [plustek] ># for adjusting the default gamma values< [plustek] ># (can also be set via frontend)< [plustek] >option redGamma 1.0< [plustek] Decoding option >redGamma< [plustek] >option greenGamma 1.0< [plustek] Decoding option >greenGamma< [plustek] >option blueGamma 1.0< [plustek] Decoding option >blueGamma< [plustek] >option grayGamma 1.0< [plustek] Decoding option >grayGamma< [plustek] >< [plustek] >#< [plustek] ># to enable TPA (EPSON or UMAX, if autodetection fails)< [plustek] ># 0 means default behaviour as specified in the internal tables< [plustek] ># 1 means enable (needed for UMAX 3450)< [plustek] >option enableTPA 0< [plustek] Decoding option >enableTPA< [plustek] >< [plustek] >#< [plustek] ># model override functionality, currently only available for< [plustek] ># Mustek devices, using NSCs' vendor ID: 0x0400 and< [plustek] ># also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)< [plustek] >#< [plustek] ># mov/PID | 0x1000 | 0x1001< [plustek] ># ---------------------------------------< [plustek] ># 0 (default)| BearPaw1200 | BearPaw 2400< [plustek] ># 1 | ignored | BearPaw 1200< [plustek] >#< [plustek] >option mov 0< [plustek] Decoding option >mov< [plustek] >< [plustek] >#< [plustek] ># and of course the device-name< [plustek] >#< [plustek] ># device /dev/usbscanner< [plustek] >#device /dev/usb1< [plustek] >< [plustek] >#< [plustek] ># to define a new device, start with a new section:< [plustek] ># [usb]< [plustek] >#< [plustek] attach (auto, 0xcfbe1470, 0x0) [plustek] Device configuration: [plustek] device name : >auto< [plustek] USB-ID : >< [plustek] model ovr. : 0 [plustek] warmup : -1s [plustek] lampOff : 300 [plustek] lampOffOnEnd : yes [plustek] cacheCalData : no [plustek] altCalibrate : no [plustek] skipCalibr. : no [plustek] skipFine : no [plustek] skipFineWhite: no [plustek] invertNegs. : no [plustek] dis.Speedup : no [plustek] pos_x : 0 [plustek] pos_y : 0 [plustek] pos_shading_y: -1 [plustek] neg_x : 0 [plustek] neg_y : 0 [plustek] neg_shading_y: -1 [plustek] tpa_x : 0 [plustek] tpa_y : 0 [plustek] tpa_shading_y: -1 [plustek] red gain : -1 [plustek] green gain : -1 [plustek] blue gain : -1 [plustek] red offset : -1 [plustek] green offset : -1 [plustek] blue offset : -1 [plustek] red lampoff : -1 [plustek] green lampoff: -1 [plustek] blue lampoff : -1 [plustek] red Gamma : 1.00 [plustek] green Gamma : 1.00 [plustek] blue Gamma : 1.00 [plustek] gray Gamma : 1.00 [plustek] --------------------- [plustek] usbDev_open(auto,) - 0x847160c0 [plustek] Vendor ID=0x04A9, Product ID=0x220D [plustek] usbio_DetectLM983x [plustek] usbio_DetectLM983x: found LM9832/3 [plustek] * setting device to idle state! [plustek] Detected vendor & product ID: 0x04A9-0x220D [plustek] Device description for >0x04A9-0x220D< found. [plustek] usb_initDev(41,0x04a9,-1) [plustek] Device WAF : 0x00000002 [plustek] Transferrate: 1000000 Bytes/s [plustek] Device Flags: 0x00000000 [plustek] Vendor adjusted to: >Canon< [plustek] LAMP-STATUS: 0x00000000 [plustek] RESETTING REGISTERS(-1) - 0x80 [plustek] SETTING THE MISC I/Os [plustek] MISC I/O after RESET: 0x66, 0x16, 0x91 [plustek] Calibration file-name set to: [plustek] >/root/.sane/Canon-N670U_N676U_LiDE20.cal< [plustek] usb_SetScanParameters() [plustek] * HDPI: 4.000 [plustek] * XDPI=150, HDPI=4.000 [plustek] * YDPI=150, MinDPIY=75 [plustek] * DataPixelStart=75, LineEnd=75 [plustek] * DataPixelStart=76, LineEnd=76 (ADJ) [plustek] >> End-Start=0, HDPI=4.00 [plustek] * Full Steps to Skip at Start = 0x0000 [plustek] * StepSize(Preset) = 121 (0x0079) [plustek] * Scan calculations... [plustek] * LineLength=6080, LineRateColor=3 [plustek] * Stepsize = 571, 0x46=0x02 0x47=0x3b [plustek] * DPD =16404 (0x4014) [plustek] * DPD =1836 (0x072c), step size=571, steps2rev=63 [plustek] * llen=6080, lineRateColor=3, qtcnt=8, hfcnt=8 [plustek] usb_GetMCLKDivider() [plustek] usb_GetMCLKDiv() [plustek] - lower mclkdiv limit=4.000000 [plustek] - upper mclkdiv limit=32.500000 [plustek] - hdpi = 4.000 [plustek] - pixelbits = 8 [plustek] - pixelsperline = 0 [plustek] - linelen = 6080 [plustek] - transferrate = 1000000 [plustek] - MCLK Divider = 0 [plustek] - Current MCLK Divider = 4 [plustek] * Integration Time Adjust = 0 (HDPI=4.000,MCLKD=4.000) [plustek] * Setting GreenPWMDutyCycleHigh [plustek] * Current MCLK Divider = 4.000000 [plustek] * MOTOR-Settings: PWM=0x08, PWM_DUTY=0x1f [plustek] * FFStepSize = 428, [0x48] = 0x01, [0x49] = 0xac [plustek] * PhyBytes = 6 [plustek] * PhyLines = 3485337796 [plustek] * TotalBytes = 3732157592 [plustek] * PL=295, coeffsize=216, scaler=3 [plustek] * PauseLimit = 295, [0x4e] = 0x91, [0x4f] = 0x01 [plustek] * Scansteps=0 (3485337801*1200/150) [plustek] usb_SetScanParameters() done. [plustek] usbDev_getCaps() [plustek] Scanner information: [plustek] Vendor : Canon [plustek] Model : N670U/N676U/LiDE20 [plustek] Flags : 0x00000000 [plustek] drvclose() [plustek] usbDev_stopScan() [plustek] usbDev_ScanEnd(), start=0, park=0 [plustek] usbDev_close() [plustek] attach: model = >N670U/N676U/LiDE20< [plustek] sane_get_devices (0xcfbe1da8, 0) device `plustek:libusb:/dev/usb1:/dev/ugen0' is a Canon N670U/N676U/LiDE20 USB flatbed scanner [plustek] sane_exit [plustek] Shutdown called (dev->fd=-1, libusb:/dev/usb1:/dev/ugen0) [plustek] Waiting for scanner-ready... [plustek] Switching lamp off... [plustek] LAMP-STATUS: 0x00000000 [plustek] LAMP-STATUS: 0x00000000 [plustek] Lamp-Timer stopped
