I am have have a problem with sane. I am using Red Hat 9. I have Benq 3300. I copied the file u222v067.bin from my windows to /etc and made the following changes as below.
#------------------------------ General ----------------------------------- # Change to the fully qualified filename of your firmware file, if # firmware upload is needed by the scanner #firmware /etc/filename.bin firmware /etc/u222v067.bin # firmware /etc/u126v043.bin # If not automatically found you may manually specify a device name. # For USB scanners also specify bus=usb, e.g. /dev/usb/scanner0 bus=usb # For SCSI scanners specify the generic device, e.g. /dev/sg0 on Linux. # /dev/sg0 so know when I start the program, after 2 minutes it gives a message " Failed to open device 'snapscane:/dev/usb/dcanner0':Error during Device I/O" after that I gave command and got following results, Please Guide Me. [root@zoni zoni]# sane-find-scanner -v searching for SCSI scanners: checking /dev/scanner... failed to open (Invalid argument) checking /dev/sg0... failed to open (Invalid argument) checking /dev/sg1... failed to open (Invalid argument) checking /dev/sg2... failed to open (Invalid argument) checking /dev/sg3... failed to open (Invalid argument) checking /dev/sg4... failed to open (Invalid argument) checking /dev/sg5... failed to open (Invalid argument) checking /dev/sg6... failed to open (Invalid argument) checking /dev/sg7... failed to open (Invalid argument) checking /dev/sg8... failed to open (Invalid argument) checking /dev/sg9... failed to open (Invalid argument) checking /dev/sga... failed to open (Invalid argument) checking /dev/sgb... failed to open (Invalid argument) checking /dev/sgc... failed to open (Invalid argument) checking /dev/sgd... failed to open (Invalid argument) checking /dev/sge... failed to open (Invalid argument) checking /dev/sgf... failed to open (Invalid argument) checking /dev/sgg... failed to open (Invalid argument) checking /dev/sgh... failed to open (Invalid argument) checking /dev/sgi... failed to open (Invalid argument) checking /dev/sgj... failed to open (Invalid argument) checking /dev/sgk... failed to open (Invalid argument) checking /dev/sgl... failed to open (Invalid argument) checking /dev/sgm... failed to open (Invalid argument) checking /dev/sgn... failed to open (Invalid argument) checking /dev/sgo... failed to open (Invalid argument) checking /dev/sgp... failed to open (Invalid argument) checking /dev/sgq... failed to open (Invalid argument) checking /dev/sgr... failed to open (Invalid argument) checking /dev/sgs... failed to open (Invalid argument) checking /dev/sgt... failed to open (Invalid argument) checking /dev/sgu... failed to open (Invalid argument) checking /dev/sgv... failed to open (Invalid argument) checking /dev/sgw... failed to open (Invalid argument) checking /dev/sgx... failed to open (Invalid argument) checking /dev/sgy... failed to open (Invalid argument) checking /dev/sgz... failed to open (Invalid argument) # No SCSI scanners found. If you expected something different, make sure that # you have loaded a SCSI driver for your SCSI adapter. # Also you need support for SCSI Generic (sg) in your operating system. # If using Linux, try "modprobe sg". searching for USB scanners: checking /dev/usb/scanner... failed to open (Invalid argument) checking /dev/usb/scanner0... open ok, vendor and product ids were identified found USB scanner (vendor=0x04a5, product=0x20b0) at /dev/usb/scanner0 checking /dev/usb/scanner1... failed to open (Invalid argument) checking /dev/usb/scanner2... failed to open (Invalid argument) checking /dev/usb/scanner3... failed to open (Invalid argument) checking /dev/usb/scanner4... failed to open (Invalid argument) checking /dev/usb/scanner5... failed to open (Invalid argument) checking /dev/usb/scanner5... failed to open (Invalid argument) checking /dev/usb/scanner7... failed to open (Invalid argument) checking /dev/usb/scanner8... failed to open (Invalid argument) checking /dev/usb/scanner9... failed to open (Invalid argument) checking /dev/usb/scanner10... failed to open (Invalid argument) checking /dev/usb/scanner11... failed to open (Invalid argument) checking /dev/usb/scanner12... failed to open (Invalid argument) checking /dev/usb/scanner13... failed to open (Invalid argument) checking /dev/usb/scanner14... failed to open (Invalid argument) checking /dev/usb/scanner15... failed to open (Invalid argument) checking /dev/usbscanner... failed to open (Invalid argument) checking /dev/usbscanner0... failed to open (Invalid argument) checking /dev/usbscanner1... failed to open (Invalid argument) checking /dev/usbscanner2... failed to open (Invalid argument) checking /dev/usbscanner3... failed to open (Invalid argument) checking /dev/usbscanner4... failed to open (Invalid argument) checking /dev/usbscanner5... failed to open (Invalid argument) checking /dev/usbscanner6... failed to open (Invalid argument) checking /dev/usbscanner7... failed to open (Invalid argument) checking /dev/usbscanner8... failed to open (Invalid argument) checking /dev/usbscanner9... failed to open (Invalid argument) checking /dev/usbscanner10... failed to open (Invalid argument) checking /dev/usbscanner11... failed to open (Invalid argument) checking /dev/usbscanner12... failed to open (Invalid argument) checking /dev/usbscanner13... failed to open (Invalid argument) checking /dev/usbscanner14... failed to open (Invalid argument) checking /dev/usbscanner15... failed to open (Invalid argument) found USB scanner (vendor=0x04a5, product=0x20b0) at libusb:002:002 # A USB device was detected. This program can't be sure if it's really # a scanner. If it is your scanner, it may or may not be supported by # SANE. Try scanimage -L and read the backend's manpage. # Scanners connected to the parallel port or other proprietary ports can't be # detected by this program. done [root@zoni zoni]# scanimage -L No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). [root@zoni zoni]#
