Hi! Sinse i switched to the 2.6 kernel my scanner not works. I have a HP ScanJet 2200C, that has work fine with the 2.4 kernel tree. I use Debian Sarge with kernel 2.6.11, and all usb modules for scanning are avaible. Libusb is installed, i work as the root user and i get following:
sane-find-scanner found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x0605 [HP ScanJet2200C]) at libusb:002:002 So i see my scanner in the lsusb and with sane-find-scanner. My installed versions are: ii libsane 1.0.15-7 API library for scanners ii sane 1.0.13-2 scanner graphical frontends ii sane-utils 1.0.15-7 API library for scanners -- utilities ii libusb-0.1-4 0.1.10a-6 userspace USB programming library But with scanimage i get always: scanimage -L No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). On the sane homepage (http://www.sane-project.org/cgi-bin/driver.pl?manu=&model=2200C&bus=any) is this scanner complete supported since plustek backend verions 0.48. plustek | 0.48 | Hewlett-Packard | status:complete | ScanJet 2200C | USB I turned all backends except the plustek off, and i taked a look in the plustek backend config of sane, but my changes on the device entry don't solve the problem. So i used the debug level 255 for sane and for the plustek backend, that gives me: export SANE_DEBUG_DLL=255 ; scanimage -L [sanei_debug] Setting debug level of dll to 255. [dll] sane_init: SANE dll backend version 1.0.11 from sane-backends 1.0.15 [dll] sane_init/read_config: reading dll.conf [dll] add_backend: adding backend `plustek' [dll] sane_init/read_dlld: processing /etc/sane.d/dll.d ... [dll] sane_init/read_dlld: considering /etc/sane.d/dll.d/libsane-extras [dll] sane_init/read_config: reading dll.d/libsane-extras [dll] sane_init/read_dlld: done. [dll] sane_get_devices [dll] load: searching backend `plustek' in `/usr/lib/sane' [dll] load: trying to load `/usr/lib/sane/libsane-plustek.so.1' [dll] load: dlopen()ing `/usr/lib/sane/libsane-plustek.so.1' [dll] init: initializing backend `plustek' [dll] init: backend `plustek' is version 1.0.0 [dll] sane_get_devices: found 0 devices No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). [dll] sane_exit: exiting [dll] sane_exit: calling backend `plustek's exit function [dll] sane_exit: finished This gives me no more informations, but the plustek backend: export SANE_DEBUG_PLUSTEK=255 ; scanimage -L [dll] init: initializing backend `plustek' [sanei_debug] Setting debug level of plustek to 255. [plustek] Plustek backend V0.49-2, part of sane-backends 1.0.15 [plustek] Retrieving all supported and conntected devices [plustek] Checking for 0x07b3-0x0010 ... [plustek] Checking for 0x03f0-0x0605 //This is my scanner !!!// ... [plustek] Checking for 0x04a9-0x220e [plustek] Available and supported devices: //it says, that the device is available ans supported!!!// [plustek] Device: >libusb:002:002< - 0x03f0x0x0605 [plustek] ># Plustek-SANE Backend configuration file< [plustek] ># For use with Plustek parallel-port scanners and< [plustek] ># LM9831/2/3 based USB scanners< ... //here comes the default config file, that i dont changes, only the following device lines!// [plustek] >#< [plustek] >< [plustek] >[usb] 0x03f0 0x0605< [plustek] next device is a USB device (0x03F0-0x0605) [plustek] ... next device [plustek] >device libusb:002:002< //i've tried here all variations, with auto, with /dev/scanner, etc, but the output was always the same!!!/ [plustek] Decoding device name >libusb:002:002< [plustek] >< [plustek] >#< ... //the rest of the config file// [plustek] >#< [plustek] attach (libusb:002:002, 0xbfffc860, (nil)) [plustek] Device configuration: [plustek] device name : >libusb:002:002< [plustek] USB-ID : >0x03F0-0x0605< [plustek] model ovr. : 0 [plustek] warmup : 15s [plustek] lampOff : 300 [plustek] lampOffOnEnd : yes [plustek] cacheCalData : no [plustek] altCalibrate : no [plustek] skipCalibr. : no [plustek] skipFine : no [plustek] skipFineWhite: no [plustek] invertNegs. : no [plustek] dis.Speedup : no [plustek] pos_x : 0 [plustek] pos_y : 0 [plustek] pos_shading_y: -1 [plustek] neg_x : 0 [plustek] neg_y : 0 [plustek] neg_shading_y: -1 [plustek] tpa_x : 0 [plustek] tpa_y : 0 [plustek] tpa_shading_y: -1 [plustek] red gain : -1 [plustek] green gain : -1 [plustek] blue gain : -1 [plustek] red offset : -1 [plustek] green offset : -1 [plustek] blue offset : -1 [plustek] red lampoff : -1 [plustek] green lampoff: -1 [plustek] blue lampoff : -1 [plustek] red Gamma : 1.00 [plustek] green Gamma : 1.00 [plustek] blue Gamma : 1.00 [plustek] gray Gamma : 1.00 [plustek] --------------------- [plustek] usbDev_open(libusb:002:002,0x03F0-0x0605) - 0x8052cd0 [plustek] Vendor ID=0x03F0, Product ID=0x0605 [plustek] usbio_DetectLM983x [plustek] UIO error [plustek] This is not a LM9831 or LM9832 chip based scanner. //i dont understand this point! It is a LM9831 or LM9832 chip based scanner!/ [plustek] open failed: -1 [dll] init: backend `plustek' is version 1.0.0 [plustek] sane_get_devices (0xbfffe988, 0) [dll] sane_get_devices: found 0 devices No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). [dll] sane_exit: exiting And the lsusb output: Bus 002 Device 002: ID 03f0:0605 Hewlett-Packard ScanJet 2200c cat /proc/bus/usb/devices T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=ff MxPS= 8 #Cfgs= 1 P: Vendor=03f0 ProdID=0605 Rev= 1.00 S: Manufacturer=Hewlett-Packard S: Product=HP ScanJet 2200C C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=16ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I need a little help with this, thanx! Greets: Adam Reviczky PS.: Sorry for the long mail, with the logs, but i've tried so much things and nothing helps. This is all information that i found for this problem. And again, it WORKS with the 2.4 kernel without any problems!
