Hi Tom, the HP 4200C is supported by the backend hp4200. So you should use the hp4200.conf instead of the hp.conf. More information about the hp4200-backend is available at http://hp4200-backend.sourceforge.net
Sincerely Peter Tom Williams wrote: > Hi! I've just installed SANE-1.0.7 on my Slackware 8-based Linux system > with these mods: > > * 2.4.18 kernel > * glibc-2.2.5 > * gcc-3.0.4 > * binutils-2.12 > > I DO have USB support compiled into my kernel and the USB ports and > scanner driver ARE being loaded (/var/log/messages output): > > Mar 25 08:50:39 c71414-a kernel: usb.c: registered new driver usbdevfs > Mar 25 08:50:39 c71414-a kernel: usb.c: registered new driver hub > Mar 25 08:50:39 c71414-a kernel: uhci.c: USB Universal Host Controller > Interface driver v1.1 > Mar 25 08:50:39 c71414-a kernel: uhci.c: USB UHCI at I/O 0xe000, IRQ 11 > Mar 25 08:50:39 c71414-a kernel: usb.c: new USB bus registered, assigned > bus number 1 > Mar 25 08:50:39 c71414-a kernel: Product: USB UHCI-alt Root Hub > Mar 25 08:50:39 c71414-a kernel: hub.c: USB hub found > Mar 25 08:50:39 c71414-a kernel: usb.c: registered new driver usbscanner > > Mar 25 08:50:39 c71414-a kernel: scanner.c: 0.4.6:USB Scanner Driver > Mar 25 08:50:39 c71414-a kernel: hub.c: USB new device connect on > bus1/2, assigned device number 2 > > /proc/bus/usb/devices output: > > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 > B: Alloc= 11/900 us ( 1%), #Int= 1, #Iso= 0 > D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 0.00 > S: Product=USB UHCI-alt Root Hub > S: SerialNumber=e000 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms > T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 > D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 > P: Vendor=03f0 ProdID=0105 Rev= 1.00 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=100mA > I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbscanner > > E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms > E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms > E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl= 1ms > > sane-find-scanner can 'see' the scanner: > > sane-find-scanner: found USB scanner (vendor = 0x03f0, product = 0x0105) > at device /dev/usb/scanner0 > > but scanimage can't seem to find the scanner: > > No scanners were identified. If you were expecting something different, > check that the scanner is plugged in, turned on and detected by the > sane-find-scanner tool (if appropriate). Please read the documentation > which came with this software (README, FAQ, manpages). > > here is my /usr/etc/sane.d/hp.conf file: > > bash-2.05a# cat /usr/etc/sane.d/hp.conf > #scsi HP > usb 0x03f0 0x0105 > /dev/usb/scanner0 > option connect-device > bash-2.05a# > > Any ideas as to why my scanner can't be found by scanimage? I > HAVE applied the HP 4200c patch to the 1.0.7 source, even though the > HP4200c patch listed 1.0.5 in the filename, so I don't know if I even > needed to apply the patch. > > Thanks in advance for your time. > > Peace.... > > Tom > > _______________________________________________ > Sane-devel mailing list > sane-de...@www.mostang.com > http://www.mostang.com/mailman/listinfo/sane-devel > > -- Peter Kirchgessner http://www.kirchgessner.net mailto:pe...@kirchgessner.net
