>>>>> "cn" == Carsten Neumann <del...@snafu.de> writes:
cn> Hi, Johan,
cn> you've missed to tell what your problems actually are!
cn> I don't see any problem why you can't use your scanner.
cn> But you haven't told that you cannot use it.
cn> What are the errors you get, if there are any?
cn> Carsten
I think from looking at the listing below it is pretty obvious that
the scsi card is detecting muliple scanners, at ID 1 Lun 00-07.
Not being familiar with this scsi card I can't really help much
except the suggest moving the ID from 1 to maybe 4 or 5. The lower
scsi ID's are usually used for hard drives.
cn> On Mon, 06 May 2002, Johan Wehtje wrote:
>> have read the docs as well as the SCSI 2.4 how to but am still none the
>> wiser as to why I get the following output from sane-find-scanner
>> ===========================================
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device
/dev/scanner
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg1
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg2
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg3
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg4
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg5
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg6
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg7
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sg8
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgb
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgc
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgd
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sge
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgf
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgg
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgh
>> sane-find-scanner: found SCSI scanner " Scanner 1.40" at device /dev/sgi
>> ======================================================
>> I only have one scanner , microtek e3 connected to a adpaptec 1524 scsi
card
>> (shipped with scanner). The aha152x scsi driver is loaded as a module.
The
>> kernel is 2.4.18. The correct irq and io are passed as params to the
module.
>> The system is a PII 400 MHZ , Asus MBrd , 128 mb RAM, Pheonix BIOS. I
have an
>> older Zip 100 disk (parralell) that is loaded as a module and sits at
sda4. I
>> have my own script for loading the zip as I need to modprobe lp before I
do,
>> then modprobe ppa.
>> I get the same result even if I don't load the zip and lp modules but
only
>> prob the aha152x module manually.
>> I am probably missing something really simple here but I can't see what
it is
>> so would appreciate some help as i have been fiddling with thsi for the
past
>> few weeks trying to get it to work.
>> BTW this is a dual boot system (win 98 SE) and the scanner works just
fine in
>> Windows , but i would really like to skip booting into windows every
time i
>> want to use the scanner.
>> anf FYI the out of "cat /proc/scsi/scsi" is below:
>> ==================================
>> Attached devices:
>> Host: scsi0 Channel: 00 Id: 06 Lun: 00
>> Vendor: IOMEGA Model: ZIP 100 Rev: D.17
>> Type: Direct-Access ANSI SCSI revision: 02
>> Host: scsi1 Channel: 00 Id: 01 Lun: 00
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> Host: scsi1 Channel: 00 Id: 01 Lun: 01
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> Host: scsi1 Channel: 00 Id: 01 Lun: 02
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> Host: scsi1 Channel: 00 Id: 01 Lun: 03
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> Host: scsi1 Channel: 00 Id: 01 Lun: 04
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> Host: scsi1 Channel: 00 Id: 01 Lun: 05
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> Host: scsi1 Channel: 00 Id: 01 Lun: 06
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> Host: scsi1 Channel: 00 Id: 01 Lun: 07
>> Vendor: Model: Scanner Rev: 1.40
>> Type: Scanner ANSI SCSI revision: 04
>> =========================================
>> Cheers
>> Johan Wehtje
>>
>> _______________________________________________
>> Sane-devel mailing list
>> sane-de...@www.mostang.com
>> http://www.mostang.com/mailman/listinfo/sane-devel
cn> _______________________________________________
cn> Sane-devel mailing list
cn> sane-de...@www.mostang.com
cn> http://www.mostang.com/mailman/listinfo/sane-devel
--
Ray Curtis
mailto:r...@ccux.com http://www.ccux.com
