Hello, my linoscan 1400 scanner (SCSI) is not recognized by scanimage under sane 1.0.8 (linux/i686 kernel 2.4.19, scsi generic module & Tekram DC390T adapter). However, it should be compatible with the umax backend.
Had no problems installing sane from source. sane-find-scanner says: > sane-find-scanner: found SCSI scanner "HDM LS4H1S V1.0" at device > /dev/scanner > sane-find-scanner: found SCSI scanner "HDM LS4H1S V1.0" at device > /dev/sg1 and `cat /proc/scsi/scsi' gives: > Host: scsi0 Channel: 00 Id: 05 Lun: 00 > Vendor: HDM Model: LS4H1S Rev: V1.0 > Type: Scanner ANSI SCSI revision: 02 while scanimage -L returns: > No scanners were identified. If you were expecting something > different, check that the scanner is plugged in, turned on and > detected by the sane-find-scanner tool (if appropriate). Please read > the documentation which came with this software (README, FAQ, > manpages). Permissions on /dev/sg1 were set correctly, and it has been linked to /dev/scanner. It seems that attach_scanner is trying to identify the linoscan, but cannot match this with its internal description. However, backend/umax-scanner.c has exactly the same description for VENDOR and MODEL, i.e. "HDM" and "LS4H1S", as has /usr/local/etc/sane.d/umax.conf. I put debug output from scanimage at the end of this mail. Any help is greatly appreciated. Best, Benedikt If I switch on debug information (i.e. SANE_DEBUG_UMAX=12), I get: % scanimage -L [sanei_debug] Setting debug level of umax to 12. [umax] sane_init [umax] This is sane-umax version 1.0 build 34 [umax] compiled with USB support for Astra 2200 [umax] (C) 1997-2002 by Oliver Rauch [umax] EMAIL: oliver.ra...@rauch-domain.de [umax] reading configure file umax.conf [umax] sanei_config_attach_matching_devices(scsi UMAX * Scanner) [umax] sanei_config_attach_matching_devices(scsi LinoHell JADE) [umax] sanei_config_attach_matching_devices(scsi LinoHell Office) [umax] sanei_config_attach_matching_devices(scsi LinoHell Office2) [umax] sanei_config_attach_matching_devices(scsi LinoHell SAPHIR2) [umax] sanei_config_attach_matching_devices(scsi HDM LS4H1S) [umax] attach_scanner: /dev/sg1, connection_type 1 [umax] attach_scanner: opening scsi device /dev/sg1 [umax] attach_scanner: sanei_scsi_open_extended returned scsi buffer size = 16384 [umax] attach_scanner: allocating SCSI buffer[0] [umax] init [umax] request_scsi_maxqueue = 2 [umax] request_preview_lines = 10 [umax] request_scan_lines = 40 [umax] handle_bad_sense_error = 0 [umax] execute_request_sense = 0 [umax] scsi_buffer_size_min = 32768 [umax] scsi_buffer_size_max = 131072 [umax] force_preview_bit_rgb = 0 [umax] slow = -1 [umax] smear = -1 [umax] calibration_area = -1 [umax] calibration_width_offset = -99999 [umax] calibration_bytespp = -1 [umax] invert_shading_data = -1 [umax] lamp_control_available = 0 [umax] backend runs on little endian machine [umax] variable scsi buffer size (usage of sanei_scsi_open_extended) [umax] initialize_values [umax] identify_scanner [umax] do_inquiry [umax] Found HDM scanner LS4H1S version V1.0 on device /dev/sg1 [umax] ERROR: attach_scanner: scanner-identification failed [umax] sanei_config_attach_matching_devices(scsi Nikon AX-110) [umax] sanei_config_attach_matching_devices(scsi Nikon AX-210) [umax] sanei_config_attach_matching_devices(scsi KYE ColorPage-HR5) [umax] sanei_config_attach_matching_devices(scsi EPSON Perfection600) [umax] sanei_config_attach_matching_devices(scsi ESCORT "Galleria 600S") [umax] sanei_usb_attach_matching_devices(usb 0x1606 0x0230) [umax] option connection-type = 1 [umax] attach_scanner: /dev/scanner, connection_type 1 [umax] attach_scanner: opening scsi device /dev/scanner [umax] attach_scanner: sanei_scsi_open_extended returned scsi buffer size = 16384 [umax] attach_scanner: allocating SCSI buffer[0] [umax] init [umax] request_scsi_maxqueue = 2 [umax] request_preview_lines = 10 [umax] request_scan_lines = 40 [umax] handle_bad_sense_error = 0 [umax] execute_request_sense = 0 [umax] scsi_buffer_size_min = 32768 [umax] scsi_buffer_size_max = 131072 [umax] force_preview_bit_rgb = 0 [umax] slow = -1 [umax] smear = -1 [umax] calibration_area = -1 [umax] calibration_width_offset = -99999 [umax] calibration_bytespp = -1 [umax] invert_shading_data = -1 [umax] lamp_control_available = 0 [umax] backend runs on little endian machine [umax] variable scsi buffer size (usage of sanei_scsi_open_extended) [umax] initialize_values [umax] identify_scanner [umax] do_inquiry [umax] Found HDM scanner LS4H1S version V1.0 on device /dev/scanner [umax] ERROR: attach_scanner: scanner-identification failed [umax] attach_scanner: /dev/sg1, connection_type 1 [umax] attach_scanner: opening scsi device /dev/sg1 [umax] attach_scanner: sanei_scsi_open_extended returned scsi buffer size = 16384 [umax] attach_scanner: allocating SCSI buffer[0] [umax] init [umax] request_scsi_maxqueue = 2 [umax] request_preview_lines = 10 [umax] request_scan_lines = 40 [umax] handle_bad_sense_error = 0 [umax] execute_request_sense = 0 [umax] scsi_buffer_size_min = 32768 [umax] scsi_buffer_size_max = 131072 [umax] force_preview_bit_rgb = 0 [umax] slow = -1 [umax] smear = -1 [umax] calibration_area = -1 [umax] calibration_width_offset = -99999 [umax] calibration_bytespp = -1 [umax] invert_shading_data = -1 [umax] lamp_control_available = 0 [umax] backend runs on little endian machine [umax] variable scsi buffer size (usage of sanei_scsi_open_extended) [umax] initialize_values [umax] identify_scanner [umax] do_inquiry [umax] Found HDM scanner LS4H1S version V1.0 on device /dev/sg1 [umax] ERROR: attach_scanner: scanner-identification failed [umax] attach_scanner: /dev/sg0, connection_type 1 [umax] attach_scanner: opening scsi device /dev/sg0 [umax] ERROR: attach_scanner: opening scsi device /dev/sg0 failed [umax] option connection-type = 2 [umax] attach_scanner: /dev/usbscanner, connection_type 2 [umax] attach_scanner: opening usb device /dev/usbscanner [umax] sanei_umaxusb_open: open of `/dev/usbscanner' failed: No such device [umax] ERROR: attach_scanner: opening usb device /dev/usbscanner failed [umax] finished reading configure file [umax] sane_get_devices(local_only = 0) No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). [umax] sane_exit
