Hello, I'm running sane 1.0.6 I have two scanners hooked up for testing. HP 5p I think it might be a hardware issue. The light comes on for a second then goes out. the carriage starts moving as to scan but only moves 1/2 inch then trys to retreat as if done and goes to clicking as to drive belt slips. Second is the MIcrotek Scanmaker II with xscanimage it can do a color preview but when it comes to scanning color it starts and completes the red pass but then errors out. with sane_start: Error during device I/O Following is a excerpt from the error.log I compiled.
The system is as follows. Vector Linux (based on slack) glibc= libc-2.2.3 gcc version 2.95.3 20010315 (release) Linux ppro 2.4.5 #5 Sun Jun 24 13:44:21 UTC 2001 i686 GenuineIntel all gui stuff stuff is exports X 4.1.0 Thanks Terry [microtek] sane_get_parameters... [microtek] sane_get_parameters: regular 3-pass color [microtek] sane_get_parameters: res_code = 33 (21) [microtek] sane_get_parameters: dots_per_mm: 3.937008 [microtek] sane_get_parameters: units_per_mm: 11.811024 [microtek] WIDTHPIX: before exp: 448 [microtek] sane_get_parameters: lines: 659 ppl: 448 bpl: 448 [microtek] set_pass_parameters: three-pass, on 2 [microtek] .wait_ready 8... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] finagle_precal... [microtek] .scanning_frame... [microtek] .scanning_frame: in- 21,35 1369,2012 [microtek] .scanning_frame: out- 21,35 1369,2012 [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] .accessory... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] .download_gamma... [microtek] .download_gamma: 256 entries of 1 bytes, max 255 [microtek] .download_gamma: by default [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] .mode_select 8... [microtek] .mode_select: pap_len: 4199 [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] .wait_ready 8... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] .start_scan... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] .get_scan_status 8... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] get_scan_status(6): 139, 1825, 65543 -> #0 [microtek] > 8b 21 7 7 0 1 [microtek] get_scan_status: busy, retry in 5... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] get_scan_status(6): 139, 1825, 65543 -> #1 [microtek] > 8b 21 7 7 0 1 [microtek] get_scan_status: busy, retry in 10... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] get_scan_status(6): 139, 1825, 65543 -> #2 [microtek] > 8b 21 7 7 0 1 [microtek] get_scan_status: busy, retry in 15... [microtek] SENSE! fd = 8 [microtek] sense = 00 00 00 00. [microtek] get_scan_status(6): 139, 1825, 65543 -> #3 [microtek] > 8b 21 7 7 0 1 [microtek] get_scan_status: busy, retry in 20... [microtek] sane_start: get_scan_status fails [microtek] end_scan... [microtek] .stop_scan...
