> I get ld: warning: ignoring file ./.libs/libtuneup-s1.a, building for macOS-x86_64 but attempting to link with file built for unknown-unsupported file format ( 0x21 0x3C 0x61 0x72 0x63 0x68 0x3E 0x0A 0x2F 0x20 0x20 0x20 0x20 0x20 0x20 0x20 )
Can you send `gf2x`'s `config.log`? This happens when you are using a linker without LTO support. Isuru On Wed, Nov 4, 2020 at 1:53 PM phiparis19 <ph.mig...@gmail.com> wrote: > > Thank you for helping me. > > I followed the instructions at the end of ./configure output (brew > install ...) > > I get ld: warning: ignoring file ./.libs/libtuneup-s1.a, building for > macOS-x86_64 but attempting to link with file built for unknown-unsupported > file format ( 0x21 0x3C 0x61 0x72 0x63 0x68 0x3E 0x0A 0x2F 0x20 0x20 0x20 > 0x20 0x20 0x20 0x20 ) > > Error installing package gf2x-1.3.0 > > I have also tried to compile sage-9.2 on another partition of my mac : il > fails after 4h of compilation for the same reason for one of the last > packages. > Le mercredi 4 novembre 2020 à 18:18:41 UTC+1, John H Palmieri a écrit : > >> >> >> On Tuesday, November 3, 2020 at 11:30:54 PM UTC-8, Dima Pasechnik wrote: >>> >>> As far as building from source is concerned, I'd recommend using >>> Homebrew, instead of trying >>> to build most packages from scratch (as it is the case if you don't use >>> it). >>> Please pay attention that you need to run >>> >>> source .homebrew-build-env >>> >>> >>> and to the list of packages you'd install printed out by ./configure >>> (at the end of its run) >>> >> >> And after installing new system packages, it's a good idea to run 'make >> distclean' and then rerun './configure' (with whatever options you want to >> pass to it). >> >> >>> >>> On Wed, Nov 4, 2020 at 6:18 AM phiparis19 <ph.m...@gmail.com> wrote: >>> > >>> > Hello, >>> > >>> > After upgrading from SageMath-9.1 to SageMath-9.2, >>> > >>> > ./sage -n jupyter fails >>> > >>> > ModuleNotFoundError: No module named '_ssl' >>> > >>> > The Jupyter notebook requires ssl, even if you do not use https. >>> Install the openssl development packages in your system and then rebuild >>> Python (sage -f python3). >>> > >>> > Unfortunately, openssl installation has failed : >>> > >>> > [openssl-1.1.1g] Undefined symbols for architecture x86_64: >>> > >>> > .... >>> > >>> > [openssl-1.1.1g] ld: symbol(s) not found for architecture x86_64 >>> > >>> > [openssl-1.1.1g] clang: error: linker command failed with exit code 1 >>> (use -v to see invocation) >>> > >>> > Same issue when recompiling sage from sage-9.2.tar.gz >>> > >>> > ./configure --enable-openssl=yes >>> > >>> > make >>> > >>> > [patch-2.7.5] ld: symbol(s) not found for architecture x86_64 >>> > >>> > >>> > I have macports and hombres installed >>> > >>> > So I dit >>> > >>> > sudo mv /opt/local /opt/local_old >>> > >>> > sudo mv /usr/local/Homebrew /usr/local/Homebrew_old >>> >>> Unless you use a non-standard installaI don't think you achieve much >>> by the latter, as Homebrew installs several packages directly into >>> /usr/local (i.e. /usr/local/bin, etc), so this is more or less just >>> breaks Homebrew, but is very far from uninstalling it. >>> >>> >>> > >>> > before typing make for sage >>> > >>> > See file enclose for configure output >>> > >>> > Thank you for helping >>> > >>> > -- >>> > You received this message because you are subscribed to the Google >>> Groups "sage-support" group. >>> >> > To unsubscribe from this group and stop receiving emails from it, send >>> an email to sage-s...@googlegroups.com. >>> >> > To view this discussion on the web visit >>> https://groups.google.com/d/msgid/sage-support/d13b96e9-92ec-4128-b219-92384d3e3110n%40googlegroups.com. >>> >>> >> -- > You received this message because you are subscribed to the Google Groups > "sage-support" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to sage-support+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/sage-support/6c90038f-0d0c-4935-bb3e-20170e82dcdbn%40googlegroups.com > <https://groups.google.com/d/msgid/sage-support/6c90038f-0d0c-4935-bb3e-20170e82dcdbn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "sage-support" group. To unsubscribe from this group and stop receiving emails from it, send an email to sage-support+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/sage-support/CA%2B01voMzLW%3DiSmrSNuHptzRgHkysnRXxHy_1EKyDv-4J8pXmfw%40mail.gmail.com.
