the top level config.log will tell you why ./configure did not accept pre-installed readline.
probably you forgot to source .homebrew... before ./configure (afk, so don't recall the exact file name, but it is the only one that starts with '.' and has homebrew in) On Thu, 17 Sep 2020, 13:24 Dima Pasechnik, <dimp...@gmail.com> wrote: > try upgrading to the latest readline (8.0.4), e.g. install as much as > possible from Homebrew, > which has this version working. > > > On Thu, Sep 17, 2020 at 1:09 PM David Joyner <wdjoy...@gmail.com> wrote: > > > > > > > > On Thu, Sep 17, 2020 at 6:54 AM Dima Pasechnik <dimp...@gmail.com> > wrote: > >> > >> in the log you attached the failure is in python3, and it's dated Aug 22 > >> > > > > Wrong log! Sorry! > > The correct one is attached I hope:-) > > > >> > >> > >> On Thu, Sep 17, 2020 at 11:12 AM David Joyner <wdjoy...@gmail.com> > wrote: > >> > > >> > I downloaded sage 9.2.b12 then ran configure and make using newly > upgraded Xcode 12. > >> > Instead of failing at python it fails at readline. The log is > attached. > >> > > >> > On Wed, Sep 2, 2020 at 12:10 PM Matthias Koeppe < > matthiaskoe...@gmail.com> wrote: > >> >> > >> >> I also see build failures of at least some of these packages at > https://github.com/mkoeppe/sage/runs/1059961873 (using a new GH workflow > that runs Xcode 12 beta, added in https://trac.sagemath.org/ticket/30487) > >> >> > >> >> I have opened https://trac.sagemath.org/ticket/30494 "Meta-ticket: > Support Xcode 12, macOS 11 Big Sur" > >> >> > >> >> On Wednesday, September 2, 2020 at 8:19:37 AM UTC-7, John H Palmieri > wrote: > >> >>> > >> >>> With a system Python and "make -k", the following packages fail: > >> >>> > >> >>> gf2x > >> >>> ecm > >> >>> symmetrica > >> >>> rubiks > >> >>> ecl > >> >>> scipy > >> >>> > >> >>> On Tuesday, September 1, 2020 at 10:29:52 PM UTC-7 Matthias Koeppe > wrote: > >> >>>> > >> >>>> These lines: > >> >>>> > >> >>>> configure:17396: checking build system compiler gcc > >> >>>> > >> >>>> etc. > >> >>>> might indicate that the configure script is confused about cross > compiling to a different architecture. > >> >>>> > >> >>>> > >> >>>> On Tuesday, September 1, 2020 at 9:59:59 PM UTC-7, John H Palmieri > wrote: > >> >>>>> > >> >>>>> > >> >>>>> > >> >>>>> On Tuesday, September 1, 2020 at 9:52:37 PM UTC-7 Matthias Koeppe > wrote: > >> >>>>>> > >> >>>>>> On Tuesday, September 1, 2020 at 8:59:14 PM UTC-7, John H > Palmieri wrote: > >> >>>>>>> > >> >>>>>>> If I do install Python 3.7, then gf2x and ecm both fail to > build. The gf2x log file says "configure: error: Cannot find a build system > compiler > >> >>>>>>> ". The ecm log file says "checking if globals are prefixed by > underscore... configure: error: Test program links neither with nor without > underscore." > >> >>>>>>>>> > >> >>>>>>>>> > >> >>>>>> > >> >>>>>> gf2x was just upgraded in https://trac.sagemath.org/ticket/30412 > - merged in 9.2.beta11. Did you test with this beta or an earlier one? > >> >>>>> > >> >>>>> > >> >>>>> I tried with 9.2.beta10, and just now I tried with this new > version of gf2x. Same error either way. Here is the gf2x config.log. > >> >>>>>> > >> >>>>>> > >> >>>>>> > >> >> > >> >> -- > >> >> You received this message because you are subscribed to the Google > Groups "sage-support" group. > >> >> To unsubscribe from this group and stop receiving emails from it, > send an email to sage-support+unsubscr...@googlegroups.com. > >> >> To view this discussion on the web visit > https://groups.google.com/d/msgid/sage-support/977efba9-1756-4c28-b23d-d7698b9c02a7o%40googlegroups.com > . > >> > > >> > -- > >> > You received this message because you are subscribed to the Google > Groups "sage-support" group. > >> > To unsubscribe from this group and stop receiving emails from it, > send an email to sage-support+unsubscr...@googlegroups.com. > >> > To view this discussion on the web visit > https://groups.google.com/d/msgid/sage-support/CAEQuuAV6ybPcOgR36tttkMQ%3DVk2KQRAy1kYXjF234OgkCDUwPQ%40mail.gmail.com > . > >> > >> -- > >> You received this message because you are subscribed to the Google > Groups "sage-support" group. > >> To unsubscribe from this group and stop receiving emails from it, send > an email to sage-support+unsubscr...@googlegroups.com. > >> To view this discussion on the web visit > https://groups.google.com/d/msgid/sage-support/CAAWYfq0M8KkC1GQnEhzA%2BYf81dhNd1rT41rPsc2x0SU8A%2BA6XA%40mail.gmail.com > . > > > > -- > > You received this message because you are subscribed to the Google > Groups "sage-support" group. > > To unsubscribe from this group and stop receiving emails from it, send > an email to sage-support+unsubscr...@googlegroups.com. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/sage-support/CAEQuuAUcBC2P1yNL-chah6%3Ds-izrXHoeQMDmPYHb_xKWZV%3DSKg%40mail.gmail.com > . > -- You received this message because you are subscribed to the Google Groups "sage-support" group. To unsubscribe from this group and stop receiving emails from it, send an email to sage-support+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/sage-support/CAAWYfq1swK5r-fK-X8f1PzTnfLhy3Wp9373KxRVRZHPw06r_LQ%40mail.gmail.com.
