I have been trying to activate my soundblaster card after installing
RedHat 6.1 so I put some details into /etc/conf.modules (see
attachments) and I used pnpdump in order to get /etc/isapnp.conf, and
after some config changes I got sound from the speakers. But, whenever I
boot the system, I get:
Loading sound module {OK}
Loading midi module can't locate module midi {FAILED}
Interesting is that I have this midi module loaded also {OK} some time
ago. But, after some other reasons I had to re-install RedHat. Before
doing that, I have put on paper details from /etc/conf.modules and
/etc/isapnp.conf in order to make proper new configuration. It looks I
missed something there.
Any suggestion regarding this problem?
Misko
alias sound mad16
pre-install sound /sbin/insmod sound dmabuf=1
alias midi op13
options op13 io=0x388
options sb mad16=1
options mad16 io=0x530 irq=10 dma=0 dma16=1 mpu_io=0x300 mpu_irq=9 joystick=1
# $Id: pnpdump.c,v 1.18 1999/02/14 22:47:18 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Board 1 has serial identifier cf 58 89 00 00 08 90 a3 55
# Board 2 has serial identifier 74 ff ff ff ff 31 09 14 3e
# (DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
# Card 1: (serial identifier cf 58 89 00 00 08 90 a3 55)
# Vendor Id UMC9008, Serial Number 1485373440, checksum 0xCF.
# Version 1.0, Vendor version 1.0
# ANSI string -->UMC PLUG & PLAY Ethernet Chip UM9008<--
#
# Logical device id UMC9008
# Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE UMC9008/1485373440 (LD 0
# Compatible device id PNP80d6
# Logical device decodes 10 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x03e0
# IO base alignment 32 bytes
# Number of IO addresses required: 32
(IO 0 (SIZE 32) (BASE 0x0220))
# IRQ 3, 4, 5, 9, 10, 11, 12 or 15.
# High true, edge sensitive interrupt
(INT 0 (IRQ 5 (MODE +E)))
(NAME "UMC9008/1485373440[0]{UMC PLUG & PLAY Ethernet Chip UM9008}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Card 2: (serial identifier 74 ff ff ff ff 31 09 14 3e)
# Vendor Id OPT0931, No Serial Number (-1), checksum 0x74.
# Version 1.0, Vendor version 0.0
# ANSI string -->OPTi Audio 16<--
#
# Logical device id OPTffff
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE OPT0931/-1 (LD 0
# ANSI string -->AUX0<--
(NAME "OPT0931/-1[0]{AUX0 }")
# (ACT Y)
))
#
# Logical device id OPT9310
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE OPT0931/-1 (LD 1
# ANSI string -->OPTi Audio 16<--
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0608
# IO base alignment 4 bytes
# Number of IO addresses required: 4
(IO 0 (SIZE 4) (BASE 0x0534))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0380
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 12
(IO 1 (SIZE 12) (BASE 0x0380))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
(IO 2 (SIZE 16) (BASE 0x0240))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e0c
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
(IO 3 (SIZE 4) (BASE 0x0e0c))
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 10 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
(DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
(DMA 1 (CHANNEL 1))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0ff0
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0534))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0380
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 12
# (IO 1 (SIZE 12) (BASE 0x0380))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e0c
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 3 (SIZE 4) (BASE 0x0e0c))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 1 (CHANNEL 0))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0534
# Maximum IO base address 0x0ff0
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0534))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0380
# Maximum IO base address 0x03f0
# IO base alignment 16 bytes
# Number of IO addresses required: 12
# (IO 1 (SIZE 12) (BASE 0x0380))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 2 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e0c
# Maximum IO base address 0x0ffc
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 3 (SIZE 4) (BASE 0x0e0c))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed type F
# (DMA 0 (CHANNEL 0))
# End dependent functions
(NAME "OPT0931/-1[1]{OPTi Audio 16 }")
(ACT Y)
))
#
# Logical device id OPT0001
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE OPT0931/-1 (LD 2
# ANSI string -->Game Port<--
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x020f
# IO base alignment 1 bytes
# Number of IO addresses required: 1
(IO 0 (SIZE 1) (BASE 0x0200))
(NAME "OPT0931/-1[2]{Game Port }")
(ACT Y)
))
#
# Logical device id OPT0002
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE OPT0931/-1 (LD 3
# ANSI string -->MPU401<--
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0360
# IO base alignment 16 bytes
# Number of IO addresses required: 2
(IO 0 (SIZE 2) (BASE 0x0300))
# IRQ 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 9 (MODE +E)))
(NAME "OPT0931/-1[3]{MPU401 }")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
#------------------------------------------------------------------
#
# /etc/isapnp.gone
#
#------------------------------------------------------------------
#
# $Id: isapnp.gone,v 0.0 1998/10/09 20:46:01 fox Exp $
#
# This file contains a list of ISA resources that are unavailable
# for PnP allocation. This may be (for instance) because they are
# standard motherboard resources, or because there is a non-PnP
# ISA card using the resources, or a device driver hasn't been
# loaded yet, so there is no sign of the resources being in use
# in /proc/*
#
# This file should be editted to suit your local machine.
#
# Resources are:
# IO base[, size] (default size 8 if ommitted)
# IRQ n
# DMA n
# MEM base,size
#
#------------------------------------------------------------------
#
# Standard motherboard stuff
#
# COM1
#
IO 0x3f8,8
IRQ 4
#
# COM2
#
IO 0x2f8,8
IRQ 3
#
# Parallel
#
IO 0x378,2
IRQ 7
#
# PS2 mouse
#
IRQ 12
#
# Sound
#
#IO 0x220,16
#IO 0x330,2
#IO 0x388,4
#IRQ 5
#DMA 1
#DMA 5
