You are all the Outaback wrenches but with Schneider before you reset
the defaults, you should just do a complete DC power down. Just in case
it is a stuck bit in config.
Dave Angelini Offgrid Solar
"we go where powerlines don't"
[2]https://offgridsolar1.com/ [3] [2]
e-mail offgridso...@sti.net
text 209 813 0060
On 2024-08-18 4:20 pm, Jay via RE-wrenches wrote:
One other thing that has worked for weird issues is a full factory
reset of everything.
Jay
On Aug 18, 2024, at 4:18 PM, Maverick Brown
<maver...@mavericksolar.com> wrote:
On OpticsRE go to devices, Mate3S, Global Charge. Disable everything
there and for good measure also set the Maximum Battery Charge to
generously large number.
Also, if you recently upgraded to Inverter software 1.6.63 or later,
you have to do some procedure to edit the maximum sell current
<preview.png>
upgrading_1_6_63_app_note [1]
PDF Document · 200 KB [1]
Thank you,
Maverick
Maverick Brown
Off-Grid Solar Commander since 2006
Maverick Solar Enterprises, Inc.
* Solar Commander Remote Power
* SunFlow Systems Cathodic Protection
maver...@mavericksolar.com
512-460-9825
On Aug 18, 2024, at 3:59 PM, Kirk Herander via RE-wrenches
<re-wrenches@lists.re-wrenches.org> wrote:
Looks like its only programmable directly on the Mate3s, not in optics
RE. Or maybe I haven;t found it yet.
On Sun, Aug 18, 2024 at 3:22 PM Jay <jay.pe...@gmail.com> wrote:
There is a setting called
FLEXnet dc advanced control.
Default is Y
I always set it to N
Pg 128 in my manual.
Jay
On Aug 18, 2024, at 11:11 AM, Kirk Herander via RE-wrenches
<re-wrenches@lists.re-wrenches.org> wrote:
Hello All,
.
I have a Radian 8048 system in service for over 10 years now. It sold
back quite normally until the last several months -3.- FM60 CC's are
set to grid tie mode and viewable and programmed from the Mate3s /
OpticsRE. This issue loosely correlates to replacing one of the CCs
several months ago.
Trouble is all -3- charge controllers are almost always in a float
mode. The radian does sell, but at a small KW compared to what it used
to before the frequent float mode started popping up. If I remember
correctly, ideally the CCs should always be in bulk charge when
sellback occurs.
I have the CC and inverter charger float set to about 1 vdc higher then
the inverter's sell volts, as I believe was recommended way back when.
Hard to understand what changed, but something did. I've checked the
relevant setpoints many times and can't find anything obviously amiss.
Does a sell mode tech note paper exist still for the Radian system? Did
it ever? Any ideas would be greatly appreciated.
--
Kirk Herander / kirkh@vermont.solar
Owner|Principal, VT Solar, LLC
_Celebrating our 33st Anniversary 1991-2024!!_
dba Vermont Solar Engineering
802.559.1225 _______________________________________________
List sponsored by Redwood Alliance
Pay optional member dues here: http://re-wrenches.org
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
There are two list archives for searching. When one doesn't work, try
the other:
https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
http://www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
http://www.members.re-wrenches.org
--
Kirk Herander / kirkh@vermont.solar
Owner|Principal, VT Solar, LLC
_Celebrating our 33st Anniversary 1991-2024!!_
dba Vermont Solar Engineering
802.559.1225 _______________________________________________
List sponsored by Redwood Alliance
Pay optional member dues here: http://re-wrenches.org
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
There are two list archives for searching. When one doesn't work, try
the other:
https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
http://www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
http://www.members.re-wrenches.org
_______________________________________________
List sponsored by Redwood Alliance
Pay optional member dues here: http://re-wrenches.org
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
There are two list archives for searching. When one doesn't work, try
the other:
https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
http://www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
http://www.members.re-wrenches.org
Links:
------
[1]
https://www.outbackpower.com/downloads/documents/appnotes/upgrading_1_6_63_app_note.pdf
[2] http://members.sti.net/offgridsolar/
[3] https://offgridsolar1.com/
_______________________________________________
List sponsored by Redwood Alliance
Pay optional member dues here: http://re-wrenches.org
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
There are two list archives for searching. When one doesn't work, try the other:
https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
http://www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
http://www.members.re-wrenches.org
